Furuno FS-1562 User manual

GMDSS Equipment
S
y
stem settin
g
s list
FS-1562
FS-75/2550
FS-5000/8000
DSC-5
DSC-6
DSC-8V
DSC-60
AA-50
DP-5
DP-6
FM-7000
FM-7500
FM-8000
FM-8500
FM-8700
DMC-5
FELCOM 10
FELCOM 11
FELCOM 12
FELCOM 80
FELCOM81
FELCOM82
REMOTE STATION
NX-500
IB-581
IB-582
TCE-59060-D
(J58-19110-0)
(0208, NAYO)

Instructions for Canceling Distress Alert
Procedure Sample message
VHF DSC
1. Switch off transmitter (transmitter and
DSC terminal) immediately.
2. Switch equipment on and set to Ch 16.
3. Make broadcast to "All Stations" giving
your vessel's name, callsign and DSC
number, and cancel the false distress
alert.
All Stations, All Stations, All Stations
This is NAME, CALLSIGN,
DSC NUMBER, POSITION.
Cancel my distress alert of
DATE, TIME, UTC.
=Master, NAME, CALLSIGN.
DSC NUMBER, DATE, TIME UTC.
MF DSC
1. Switch off equipment (transmitter and
DSC terminal) immediately.
2. Switch equipment on and tune for
Radiotelephony transmission on
2182 kHz.
3. Make broadcast to "All Stations" giving
the vessel's name, callsign and DSC
number, and cancel the false distress
alert.
All Stations, All Stations, All Stations
This is NAME, CALLSIGN,
DSC NUMBER, POSITION.
Cancel my distress alert of
DATE, TIME, UTC
=Master, NAME, CALLSIGN.
DSC NUMBER, DATE, TIME UTC.
HF DSC
Same as for MF but the alert must be cancelled on all the frequency bands on which it
was transmitted. Hence, the transmitter should be tuned consecutively to the
radiotelephony distress frequencies in the 4, 6, 8, 12 and 16 MHz bands, as necessary.
Inmarsat C
Notify the appropriate RCC to cancel the
alert by sending a distress priority message
via the same CES through which the false
distress alert was sent.
NAME, CALLSIGN, IDENTITY NUMBER,
POSITION,
Cancel my Iinmarsat-C
distress alert of DATE, TIME, UTC
=Master +
EPIRB
If for any reason, an EPIRB is activated accidentally, the ship should contact the nearest
coast station or an appropriate coast earth station or RCC and cancel the distress alert.
* Notwithstanding the above, a ship may use any means available to inform the
appropriate authorities that a false distress alert has been transmitted and should be
cancelled.
* No action will normally be taken against any ship or mariner for reporting and
canceling a false distress alert. However, in view of the serious consequences of false
alert, and the strict ban on their transmission, Governments may prosecute in cases of
repeated violations.

i
GMDSS equipment key points
Equipment Menu (Item) Pass word/key point Note
[SELECT] “PRG” System settings
[SETUP] [4]:XMITR
Re-enter the MMSI
Ignore ID ON
[SETUP] “I”, enter to
“652111” Selection of VHF or
MF/HF
[SETUP] [5]:SCAN Set the RX SCAN
frequency as “99999.9”. To canceling SCAN frequency
DSC-5
[SETUP] [1]:Position [SELECT] [1];
Set the UTC as “9999”. To canceling manual position data.
[SELECT] [9] :System System settings
[SELECT] [!]:dimmer [SELECT] [9] “P”, enter
to
“652111”. For test
[SELECT] [0]:SCAN Set the RX SCAN
frequency as “99999.9”. To canceling SCAN frequency
[SELECT] [1]:Position [SELECT] [1];
Set the UTC as “9999”. To canceling manual position data.
DSC-6
[SELECT] [9] “MMSI”
(Re-enter the MMSI) EEROM clear (NMI SW ON) Ver-1.05 and after
[SELECT] [9]:System System settings
[SELECT] [!]:dimmer For test
[SELECT] [8]:Receiver
[SELECT] [9] “P”,
enter to “652111”. Selection of VHF or
CH70
DSC-8V
[SELECT] [1]:Position [SELECT] [1];
Set the UTC as “9999”. To canceling manual position data.
[SETUP] “System” [SETUP] “Protection”,
enter to “652111”. System settings
Re-enter the MMSI EEROM clear
(NMI SW ON), enter to
“652111”
DSC-60
Confirmation of present Version
number [3]:TEST, press [1] key five times while pressing
[#FILE] key.
[SELECT] [9] :System System settings
[SELECT] [!]:dimmer [SELECT] [9] “P”,
enter to “652111”. For test
[SELECT] [1]:Position [SELECT] [1];
Set the UTC as “9999”. To canceling manual position data.
[SELECT] [9] “MMSI”
(Re-enter the MMSI)
FM-8500
[SELECT] [9] “private”
EEROM clear
(NMI SW ON) DSC Ver-03 and later.
[SELECT] [9] :System System settings
[SELECT] [!]:dimmer [SELECT] [9] “P”,
enter to “652111”. For test
[SELECT] [1]:Position [SELECT] [1];
Set the UTC as “9999”. To canceling manual position data.
[SELECT] [9] “MMSI”
(Re-enter the MMSI)
FM-8700
[SELECT] [9] “private”
EEROM clear
(NMI SW ON)

ii
Equipment Menu (Item) Pass word/key point Note
System settings;
(CH preset, Mode selection, etc) Jumper connection and press S17 on PANEL
board.
ATIS setting JP-1: SUB-CPU board.
CH70 setting JP-2: SUB-CPU board.
FM-7000
Setting to connect DSC JP-2: PANEL board
JP-2: SUB-CPU board.
FM-7500 Refer to DSC-5 and FM-7000
FM-8000 System settings menu.
Turn the power on while
pressing and holding the
[CH16] key, enter to
“652111”.
System settings menu.
Turn the power on while
pressing and holding the
[RCL] key, select the
system CH 9999, then
press the [RCL] “1562”
and [ENT] key.
Channel presetting CH 1 to 200 To erase CH;
[RCL] [0] [ENT]
Power adjustment [ENT]+[8]:HI power [ENT]+[9]:LOW power
[ENT]+[7]:TUNE power
System CH 9998 “0”.
Self test (Transceiver unit) Turn the power on while
pressing and holding the
[TX] key.
Set the RF gain VR
maximum.
FS-1562
Self test (LCD/key/Ver) Turn the power on while
pressing and holding the
[ENT] key.
System settings menu.
Turn the power on while
pressing and holding the
[RCL] key, select the
system CH 9999, then
press the [CH] “75” and
[ENT] key.
Channel presetting Each band; 0,1,2,4,6 ---25
To erase CH;
[Freq.] [0] [ENT]
Power adjustment [ENT]+[8]:HI power
[ENT]+[9]:LOW power
[ENT]+[7]:TUNE power
System CH 9998 “0”.
Self test (Transceiver unit) Turn the power on while
pressing and holding the
[CURSOL] key.
Set the RF gain VR
maximum.
FS-75/2550
Self test (LCD/key/Ver) Turn the power on while pressing and holding the
[ENT] key.

iii
Equipment Menu (Item) Pass word/key point Note
AT-1560 Self test
Turn on No.2 of the dip
SW S2 in the ATU, then
press the TUNE SW in the
ATU.
To conform System
settings [RCL] 9999
[ENT].
System settings menu. [STO] “system setting item No.” [ENT] “ setting
No.” [ENT].
To conform user CH
setting [RCL] 9998
[ENT].
Channel presetting
To preset;
[STO] “CH No.” [ENT]
[ENT].
To eras;
[STO] “CH No.” [ENT]
[0] [ENT].
Power adjustment
FULL power;
[STO] [FULL] adjust to
power by [FULL] or
[UP] key.
LOW power
[STO] [LOW] adjust to
power by [FULL] or
[UP] key.
FS-
5000/8000
BFO setting [STO] [BFO] To keep ”1700Hz”.
[F5] 6: AAB Re-enter AAB;
Type “ANSWER CODE”
(Type Cap. letter)
[F5] 7, 8, 9, 0: IDs Re-enter IDs;
Type “ID CODE”
(Type Cap. letter)
[F6]:Terminal
DP-5
[F8]:System
Changing system settings
Type “DP5”
(Type Cap. letter)
[F5] 5: AAB Re-enter AAB;
Type “ANSWER CODE”
(Type Cap. letter)
[F5] 6, 7, 8, 9: IDs Re-enter IDs;
Type “ID CODE”
(Type Cap. letter)
[F6]: System
Changing system settings
Type “DP6”
(Type Cap. letter)
Quit to application softwear. [Fn ]+ [F2] + [Alt] Ver 16 or later
Terminal program update. B:\>install
Main program up date.
B:\>
Type “nbdpinst”,
press [F1],
type “nbdp.exe”.
DP-6
Printer and Language settings. [Fn ]+ [F1], type “DP6”.
(Type Cap. letter)

iv
Equipment Menu (Item) Pass word/key point Note
FELCOM 10 None
FELCOM 11 Terminal program update. B:\>
Type “ibinst”. IB-581
Quit to application softwear. [Fn ]+ [Alt] + [F2]
Terminal program update. B:\>
Type “ibinst”.
CPU-2 program updata. B:\>
Type “upf12”,
Turn on the power.
FELCOM 12
Confirm to terminal program
version. [Fn ] + [Alt] + [F1]
[F4] [3] [7]:AAB Re-enter AAB;
[Alt]+[Ctrl],
type “ANSWER”
[F4] [6] [6]: commissioning menu Job No.:
FURUNOSERVICE
Pass word: FELCOM80 IMN and OID/DID
[F4] [6][7]: manual control menu
“S2-#8 ON” on the CPU 2
board.
Job No.:
FURUNOMANUAL
Pass word: 2582
Maintenance code
“Status monitor & log print” *91#
Maintenance code
“Status monitor *96#
Maintenance code
“Self test” *90#
Maintenance code
“ADJ to Rx level (Fax by voice
CH)”
*70xx#
(xx:50 to 82 default 70)
Maintenance code
“ADJ to Tx level (Fax by voice
CH)”
*79xx#
(xx:22 to 42 default 30)
FELCOM 80
Maintenance code
Return to default settings;
(All setup item from No.1 TEL) *60#
No.1 telephone

v
Equipment Menu (Item) Pass word/key point Note
[F4] [3] [8]:AAB Re-enter AAB; [Alt]+[Ctrl],
type “ANSWER”
[F4] [6] [6]: commissioning menu Job No.:
FURUNOSERVICE
Pass word: FELCOM81 OID/DID
[F4] [6][7]: manual control menu
“S1-#8 ON” on the CPU 2
board.
Job No.:
FURUNOMANUAL
Pass word: 3504
Maintenance code
“Status monitor & log print” *91#
Maintenance code
“Status monitor *96#
Maintenance code
“Self test” *90#
Maintenance code
“ADJ to Rx level (Fax by voice
CH)”
*70xx#
(xx:50 to 82 default 70)
No.1 telephone
Maintenance code
“Echo cancel” *99ab# Each telephone
Maintenance code
“ADJ to Tx level (Fax by voice
CH)”
*79xx#
(xx:22 to 42 default 30)
Maintenance code
Return to default settings;
(All setup item from No.1 TEL)
*60# No.1 telephone
FELCOM 81
Terminal program update. B:\>
Type “ibinst”.
PFX-50 All memory clear [1][3][*], power on
FC622SL1
WG: TEL Setting “Pb” [STO] [#][*][STO]
FC755D1:
TEL Setting “Pb” DIP SW-#1 “ON”

Content
1
A. MF/HF SSB Radiotelephone
Section A1. FS-1562-15/25
1.Connection...................................................................................................... 1
2.System settings............................................................................................... 2
2.1 Procedure........................................................................................ 2
2.2 System channel list (Ver-09)............................................................ 3
2.3 System channel list (Ver-03)............................................................ 5
2.4 System settings descriptions ........................................................... 6
2.5 LCD/Keyboard test & ROMVersion No.Confirmation...................... 7
3.Channel Programming.................................................................................... 8
4.Power Data Setting ....................................................................................... 10
5.Self test......................................................................................................... 12
5.1 Transceiver unit.............................................................................. 12
5.2 Antenna coupler unit...................................................................... 13
Section A2. FS-75/2550
1.Connection...................................................................................................... 1
2.System settings............................................................................................... 2
2.1 Procedure........................................................................................ 2
2.2 System channel list (Ver-09)............................................................ 3
2.3 System settings descriptions ........................................................... 5
2.4 LCD/Keyboard test & ROMVersion No.Confirmation...................... 6
3.Channel Programming.................................................................................... 7
4.Power Data Setting ......................................................................................... 9
5.Self Test ........................................................................................................ 11
5.1 Transceiver unit.............................................................................. 11
5.2 Antenna coupler unit...................................................................... 12
Content

Content
2
Section A3. FS-5000/8000
1.Connection ..................................................................................................... 1
2.System settings .............................................................................................. 2
2.1System Channel List......................................................................... 2
2.2Confirmation of settings.................................................................... 6
2.3System channel description ............................................................. 7
2.4Default setting for each country...................................................... 12
3.Jumper settings ............................................................................................ 13
3.1For NAV data format selecting, CIF or NMEA................................. 13
3.2When using C.Loop between FS-5000/8000 and DB-500.............. 13
4.User (Preset) Channel Programming............................................................ 15
5.Power Adjustment......................................................................................... 16
6.Self test......................................................................................................... 21
6.1Transceiver unit .............................................................................. 21
6.2 Antenna Coupler unit..................................................................... 22
B. DSCTerminal
Section B1. DSC-5
1.Connection ..................................................................................................... 1
2.Changing System Settings and MMSI number............................................... 3
2.1Changing system settings................................................................ 3
2.2Settings List...................................................................................... 5
3.Jumper wire settings....................................................................................... 8
4.Self test........................................................................................................... 9
5.Clearing Contents of S-RAM and EEROM ................................................... 10
6.DSC Frequency table.................................................................................... 12
7.Menu tree ..................................................................................................... 13
8.Power and Frequency measurement of MF/HF Radiotelephone.................. 17
9.Power and Frequency measurement ofVHF Radiotelephone ...................... 18