Gaggia Milano VIVA PRESTIGE RI84 Series User manual

RI8437, RI8435, RI8433
4222.200.0739.1 RI84xx POEMIA GAGGIA FRONTcover_HR.pdf 1 05-10-17 14:47

14
13
15
16
17
19
21 2220
18
12
1110
5
8 9
6
7
2
1
4
3
1

English 6
Dansk 17
Deutsch 28
Español 41
Français 53
Italiano 65
Nederlands 77
Norsk 89
Português 100
Svenska 112
Ελληνικα 123
Русский 135

English
Introduction
This coffee machine is suitable for preparing 1 or 2 cups of espresso coffee and is equipped with a
swivel steam and hot water wand. The controls on the front of the machine are labeled with easy-to-
read symbols. The machine has been designed for domestic use and is not suitable for professional,
continuous use.
Clean cold water
Use clean cold water every day. If you have not used the coffee machine for one day, you have to
flush it with clean cold water before you use it again. To flush the machine, fill the water tank with
clean cold water, place a bowl or 2 cups under the coffee spout and brew hot water until the water
tank is empty.
Energy saving
The RI8437, RI8435, RI8433 machines are equipped with an auto power-off function for energy saving.
The auto power-off function automatically activates 30 minutes after setting the main switch to 'I'. To
switch the machine back on, set the main switch back to 'I'.
Important safety information
This machine is equipped with safety features. Nevertheless, read and follow the safety instructions
carefully and only use the machine as described in these instructions, to avoid accidental injury or
damage due to improper use of the machine. Keep this safety booklet for future reference.
Warning
-Check if the voltage indicated on the machine corresponds to the
local mains voltage before you connect the appliance.
-Connect the machine to an earthed wall socket.
-Do not let the power cord hang over the edge of a table or
worktop and do not let it touch hot surfaces.
-To avoid the danger of electric shock, never immerse the machine,
mains plug or power cord in water.
-If the mains cord is damaged, you must have it replaced by
Gaggia, a service center authorized by Gaggia or similarly
qualified person in order to avoid a hazard.
-Do not pour liquids on the power cord connector.
-To avoid the danger of burns, keep body parts away from hot
water jets produced by the machine.
-Do not touch hot surfaces. Use handles and knobs.
6English

-Switch off the machine with the main switch located on the back
and remove the mains plug from the wall socket:
-If a malfunction occurs.
-If you are not going to use the appliance for a long time.
-Before you clean the machine.
-Pull at the plug, not at the power cord.
-Do not touch the mains plug with wet hands.
-Do not use the machine if the mains plug, the power cord or the
machine itself is damaged.
-Do not make any modifications to the machine or its power cord.
-Only have repairs carried out by a service center authorized by
Gaggia to avoid ahazard.
-The machine should not be used by children younger than 8
years old.
-This machine can be used by children aged from 8 years and
above and by persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
machine in a safe way and if they understand the hazards
involved.
-Cleaning and user maintenance shall not be made by children
unless they are older than 8 and supervised.
-Keep the machine, its accessories and its cord out of the reach of
children aged less than 8 years.
-Children should be supervised to ensure that they do not play
with the machine.
-Be carefull when you dispense hot water. Dispensing may be
preceded by small jets of hot water. Wait until the end of the
dispensing cycle before you remove the hot water dispensing
spout.
-To avoid the danger of burns, be aware that dispensing may be
preceded by small jets of hot water. Never touch the classic milk
frother with bare hands, as it may become very hot.
7
English

-Only use this espresso maker for its intended use to avoid
potential injury.
Caution
-Always return the machine to a service center authorized by
Gaggia for examination or repair. Do not attempt to repair the
machine yourself, otherwise your warranty becomes invalid
-The machine is intended for normal household use only. It is not
intended for use in environments such as staff kitchens of shops,
offices, farms or other work environments. Nor is it intended to be
used by clients in hotels, motels, bed and breakfast and other
residential environments.
-Always put the machine on a flat and stable surface. Keep it in
upright position, also during transport.
-Do not place the machine on a hotplate or directly next to a hot
oven, heater or similar source of heat.
-When you clean the machine, let it cool down before you insert or
remove any parts. The heating surface may retain residual heat
after use.
-Never fill the water tank with warm, hot or sparkling water, as this
may cause damage to the water tank and the machine.
-Never use souring pads, abrasive cleaning agents or aggressive
liquids such as petrol or acetone to clean the machine. Simply use
a soft cloth dampened with water.
-Descale your machine every 3 months. Not doing this will make
your machine stop working properly. In this case repair is not
covered by your warranty.
-Do not keep the machine at temperatures below 0°C/32°F. Water
left in the heating system may freeze and cause damage.
-Do not leave water in the water tank when you are not going to
use the machine for a long period of time. The water can become
contaminated. Use fresh water every time you use the machine.
8English

-Never use any accessories or parts from other manufacturers or
that Gaggia does not specifically recommend. If you use such
accessories or parts, your warranty becomes invalid.
-Regular cleaning and maintenance prolongs the lifetime of your
machine and ensures optimum quality and taste of your coffee.
-The machine is exposed continuously to moisture, coffee and
scale. Therefore it is very important to regularly clean and
maintain the machine as described in the user manual and shown
on the website. If you do not perform these cleaning and
maintenance procedures, your machine eventually may stop
working. In this case repair is not covered by warranty.
-Never drink the solution dispensed during the descaling process.
-The machine shall not be placed in a cabinet when in use.
-After frothing milk, quickly clean the classic milk frother by
dispensing a small quantity of hot water into a container. Then
remove the external part of the classic milk frother and wash it
with lukewarm water.
-Never pour any other liquid than clean cold water into the water
tank.
-Do not clean the pressurized filter holder in the dishwasher. This
will damage the pressurized filter holder.
Electromagnetic fields (EMF)
This machine complies with all applicable standards and regulations regarding exposure to
electromagnetic fields.
Machine overview
1 Power-on light
2 Steam ready light
3 Machine ready light
4 Selection knob
5 Ground coffee filter
6 Pressurized filter holder
7 Brew unit
8 Drip tray cover (specific types only)
9 Drip tray
10 User interface
11 Cup holder rest
12 Water tank
9
English

13 Lid of the water tank
14 Ground coffee measuring scoop
15 Pod filter adapter (specific types only)
16 Coffee pod filter (specific types only)
17 Seat for accessories
18 Seat for coffee measuring scoop
19 Hot water/steam knob
20 Classic milk frother (specific types only)
21 Power cord
22 Main switch (RI8437, RI8435, RI8433) with energy saving switch)
First installation
1Remove all packaging material from the machine.
2Place the machine on a table or worktop away from the tap, the sink and heat sources.
Note: Leave at least 15 cm of free space above, behind and on both sides of the machine (Fig. 2).
Preparing for use
1Remove the lid of the water tank and remove the water tank from the machine (Fig. 3).
2Rinse the water tank. Fill the water tank with fresh water up to the MAX indication (Fig. 4).
3Place the water tank back into the machine and push it downwards until the reference marks are
visible (Fig. 5).
4Place the lid of the water tank back onto the machine.
Circuit priming
When you use the machine for the first time, after dispensing steam or when the water tank is empty,
perform the following steps:
1Place a container under the milk frother and turn the hot water/steam knob anticlockwise (Fig. 6).
2Insert the mains plug into a wall socket.Set the main switch to 'I' to switch on the machine (Fig. 7).
-The power-on light lights up.
3Turn the selection knob to the coffee position (Fig. 8).
-Hot water comes out of the milk frother.
4When the water tank is empty, turn the selection knob back to the standby position (Fig. 9).
5Turn the hot water/steam knob clockwise. Remove the container (Fig. 10).
Manual rinsing cycle
1Rinse the water tank. Fill the water tank with fresh water up to the MAX indication (Fig. 4).
2Place the water tank back into the machine and push it downwards until the reference marks are
visible (Fig. 5).
3Place a container under the classic milk frother and turn the hot water/steam knob anticlockwise
(Fig. 6).
4Turn the selection knob to the coffee position (Fig. 8).
-Let the machine dispense water until the water tank is empty.
5Turn the selection knob back to standby position (Fig. 9).
6Fill the water tank with fresh water up to the MAX indication.
7Insert the pressurized filter holder into the brew unit from below (Fig. 11).
8Turn the filter holder from left to right as far as possible and release the filter holder grip. The
handle will automatically jump back to the left again (Fig. 12).
10 English

9Place a container under the filter holder (Fig. 13).
10 Turn the selection knob to the coffee position (Fig. 8).
-Let the machine dispense water until the water tank is empty.
11 When the water tank is empty, turn the selection knob back to the standby position (Fig. 9).
12 Fill the water tank with fresh water up to the MAX indication and wait until the 'machine ready' light
lights up.
13 Turn the filter holder from right to left to remove it from the brew unit and rinse it with fresh water
(Fig. 14).
The machine is ready for use.
Using the machine
Note: Clean the coffee pod filter and coffee pod adapter every time you have used it.
Brewing coffee with ground coffee
Warning: To prevent the risk of burns, do not turn the pressurized filter holder to remove
it during brewing.
1Preheat the pressurized filter holder before the first coffee brewing.
2Insert the filter holder into the brew unit from below (Fig. 11).
3Turn the filter holder from left to right until it locks into place and release the filter holder grip (Fig.
12). The handle will jump back to the left slightly.
4Turn the selection knob to the coffee position until some water flows out of the coffee dispensing
openings (Fig. 8).
5Brew one cup of water. Turn the selection knob to the standby position to stop brewing (Fig. 9).
6Turn the filter holder from right to left to remove it from the machine and pour out the remaining
water (Fig. 15).
Note: Remove any coffee residues from the rim of the filter holder.
7Use the measuring scoop to put the ground coffee into the pressurized filter holder.
-To brew one cup of coffee, add 1-1.5 measuring scoops of ground coffee.
-To brew two cups of coffee, add 2 measuring scoops of ground coffee (Fig. 16).
Note: The pressurized filter holder automatically tamps the ground coffee. There is no need to
tamp the ground coffee yourself.
8Insert the ground coffee filter into the pressurized filter holder (Fig. 17).
Note: When you use the machine for the first time, the ground coffee filter is already inserted.
9Insert the filter holder into the brew unit.
10 Turn the filter holder from left to right until it locks into place and release the filter holder grip (Fig.
12). The handle will jump back to the left slightly.
11 Place one or two cups under the pressurized filter holder (Fig. 18).
Note: Make sure the cups are placed correctly under the coffee dispensing openings.
12 Turn the selection knob to the coffee position.
-The machine starts brewing coffee.
13 Turn the selection knob to the standby position when the cup(s) contain(s) the desired amount of
coffee.
14 Remove the pressurized filter holder and empty it. Clean the pressurized filter under a running tap.
11
English

Brewing coffee with coffee pods
Note: Only use the coffee pod filter and coffee pod filter adapter with coffee pods
1Use a teaspoon to remove the ground coffee filter from the pressurized filter holder (Fig. 19).
2Insert the pod filter adapter with the convex side facing down into the pressurized filter holder (Fig.
20).
3Place the coffee pod filter on top of the pod filter adapter in the filter holder (Fig. 21).
4Insert the pressurized filter holder into the brew unit from below (Fig. 11).
5Turn the filter holder from left to right until it locks into place and release the filter holder grip (Fig.
12). The handle will turn to the left slightly.
Note: For the first coffee brewing session, you need to preheat the pressurized filter holder.
6Brew one cup of water. Turn the selection knob to the standby position to stop brewing (Fig. 9).
7Turn the filter holder from right to left to remove it from the machine and pour out the remaining
water (Fig. 15).
8Insert a coffee pod into the filter holder (Fig. 22).
Note: Make sure the paper of the pod does not stick out beyond the edge of the filter holder.
9Insert the filter holder into the brew unit from the below.
10 Turn the filter holder from left to right until it locks into place and release the filter holder grip. The
handle will turn to the left slightly.
11 Place a cup under the filter holder.
12 Turn the selection knob to the coffee position (Fig. 8).
-The machine starts brewing coffee.
13 Turn the selection knob to the standby position when the cup contains the desired amount of
coffee.
14 Remove the filter holder and throw away the used coffee pod.
Dispensing hot water
Warning: To avoid the danger of burns, be aware that dispensing may be preceded by
small jets of hot water and only move the steam wand by means of the protective
handle.
1Place a container or a glass under the classic milk frother.Turn the hot/water steam knob
anticlockwise (Fig. 6).
2Turn the selection knob to the coffee position. (Fig. 8)
-The machine starts dispensing hot water.
3Turn the selection knob to the standby position when the machine has dispensed the desired
amount of water (Fig. 9).
4Turn the hot/water steam knob clockwise. Remove the container or the glass (Fig. 10).
Frothing milk
Warning: To avoid the danger of burns, be aware that dispensing may be preceded by
small jets of hot water and only move the steam wand by means of the protective
handle.
1Place a cup under the milk frother.
2Turn the selection knob to the steam position
12 English

-The 'machine ready' light goes out.
3Wait until the 'steam ready' light lights up. Then the machine is ready to dispense steam.
4Turn the selection knob to the steam position to let out any water in the milk frother (Fig. 23).
5Turn the selection knob back to standby position. Remove and empty the cup
6Fill 1/3 of a jug with cold milk (Fig. 24).
7Place the jug under the milk frother.
8Turn the hot water/steam knob anticlockwise. Gently stir the jug to create foam and turn the hot
water/steam knob clockwise.
9Remove the jug.
10 Place a cup under the milk frother, let the rest water and milk flow out of the milk frother. Remove
the cup.
Cleaning
Regular cleaning and descaling prolongs the lifetime of your machine and ensures optimum quality
and taste of your coffee.
Warning: Do not immerse the machine in water or any other liquid.
Warning: Never use scouring pads, abrasive cleaning agents or aggressive liquids to
clean the machine.
Warning: Always unplug the machine and let it cool down before you clean it.
Warning: Only use a soft, damp cloth to clean the machine.
Cleaning the drip tray
1Pull the drip tray out of the machine (Fig. 25).
2Empty and rinse the drip tray under the tap.
3Slide the drip tray back into the machine.
Cleaning the classic milk frother (specific types only)
Note: After brewing milk-based beverages clean the classic milk frother.
1Remove the tube of the classic milk frother (Fig. 26).
2Rinse it with fresh water (Fig. 27).
3Remove the plastic handle of the classic milk frother from the steam wand and rinse it with fresh
water (Fig. 28).
4Clean the steam wand with a wet cloth.
5Slide the plastic handle back onto the steam wand.
6Slide the tube back onto the steam wand.
Cleaning the pressurized filter holder
1Remove the ground coffee filter or coffee pod filter from the filter holder and rinse it thoroughly
with hot water.
13
English

2If present, remove the pod filter adapter from the filter holder and rinse it thoroughly with hot
water.
3Rinse the inside and outside of the pressurized filter holder with hot water (Fig. 14).
Caution: Do not clean the pressurized filter holder in the dishwasher. This will damage the
pressurized filter holder.
Descaling
Please use Gaggia descaler only. Under no circumstances should you use a descaler based on sulfuric
acid, hydrochloric acid, sulfamic or acetic acid (vinegar) as this may damage the water circuit in your
machine and not dissolve the limescale properly. Not using the Gaggia descaler will void your
warranty. Failure to descale the appliance will also void your warranty.
Descaling procedure
1Insert the pressurized filter holder in the brew unit.
2Remove and empty the water tank.
3Pour half of the descaling solution into the water tank. Fill the water tank with fresh water up to the
MAX indication. Place the water tank back into the machine.
4Set the main switch to 'I' to switch on the machine. Turn the selection knob to the standby position.
5Place a container under the classic milk frother.
6Wait until the coffee ready light lights up and brew two cups (of approx. 150ml each) of water.
7Set the main switch to 'O' to switch off the machine.
8Let the descaling solution work for 15-20 minutes with the machine switched off.
9Set the main switch to 'I' to switch the machine back on.
10 Fill two cups (of approx. 150ml each) with hot water from the classic milk frother.
11 Set the main switch to 'O' to switch off the machine and wait 3 minutes.
12 Repeat steps 9-11 until the water tank is empty.
13 Rinse the water tank and fill it with fresh water up to the MAX indication.
14 Place a container under the filter holder.
15 Set the main switch to 'I' to switch on the machine and turn the selection knob to the standby
position.
16 Let the machine dispense water until the water tank is empty. Set the selection knob to the
standby position.
17 Fill the water tank with fresh water up to the MAX indication.
18 Place a large container under the classic milk frother. Turn the hot water/steam knob anticlockwise.
19 Turn the selection knob to the coffee position and let the machine dispense water until the water
tank is empty.
20 Turn the selection knob to the standby position.
21 Turn the hot water/steam knob clockwise.
22 Rinse the machine by repeating steps 13-20 one more time.
23 Remove the filter holder from the brew unit by turning it from right to left and rinse it with fresh
water.
24 Fill the water tank with fresh water up to the MAX indication.
The machine is now ready for use.
14 English

Troubleshooting
This chapter summarizes the most common problems you could encounter with the machine. For
support, contact your local dealer or an authorized service center. Contact details are included in the
warranty booklet supplied separately or visit www.gaggia.com/n-m-co/espresso/world-wide or
www.gaggia.it/n-m-co/espresso/contact.
Problem Possible cause Solution
The machine does not
switch on.
The machine is not
connected to a wall socket.
Connect the machine to a wall socket.
The main switch is in off
position.
Make sure the main switch is in on
position.
The pump is very noisy. There is no water in the
water tank.
Fill the water tank with water.
The water tank is not
positioned correctly.
Place the water tank back into the
machine and push it downwards until
the reference marks are visible.
The coffee is too cold. The filter holder is not
inserted for preheating.
Preheat the filter holder.
The 'machine ready' light was
off when you turned the
selection knob to the coffee
position.
Wait until the 'machine ready' light lights
up.
The cups are cold. Preheat the cups with hot water.
The milk does not froth. You used a type of milk that
is unsuitable for frothing
(powdered milk or low-fat
milk).
Only use cold whole milk for frothing.
It is not possible to
prepare a cappuccino.
The classic milk frother is not
clean.
Clean the classic milk frother.
There is no steam left in the
boiler.
Prime the circuit.
No coffee or only drops of
coffee come out of the
machine.
The hot water/steam knob is
in the 'open' setting (turned
anticlockwise).
Turn the hot water/steam knob to the
'closed' setting (turned clockwise).
Scale has built up inside the
machine.
Descale the machine
The ground coffee filter or
coffee pod filter in the filter
holder is clogged.
Clean the ground coffee filter or coffee
pod filter.
You used an unsuitable
coffee pod.
Use a coffee pod suitable for this
machine.
The ground coffee you use is
ground too finely.
Use ground coffee with a coarser grind.
15
English

Problem Possible cause Solution
The ground coffee was
pressed into the ground
coffee filter
Make sure you do not press the ground
coffee into the ground coffee filter.
There is too much ground
coffee in the ground coffee
filter.
Reduce the quantity of ground coffee in
the ground coffee filter.
Coffee flows out along the
edges of the filter holder.
You have not attached the
filter holder to the brew unit
properly.
Attach the filter holder correctly.
The upper edge of the filter
holder is not clean.
Clean the upper edge of the filter holder.
The coffee pod is not
inserted correctly.
Insert the coffee pod correctly. Make
sure its edges do not stick out beyond
the edge of the filter holder.
There is too much ground
coffee in the ground coffee
filter.
Reduce the amount of ground coffee in
the ground coffee filter with the
measuring scoop.
The machine switches off
while brewing coffee or
dispensing hot water
(RI8437, RI8435, RI8433).
The energy saving modus is
on
Set the main switch to 'I' to switch the
machine back on.
Warranty and support
For support, contact your local dealer or an authorized service center. Contact details are included in
the warranty booklet supplied separately or visit www.gaggia.com/n-m-co/espresso/world-wide
orwww.gaggia.it/n-m-co/espresso/contact.
Recycling
-This symbol means that this product shall not be disposed of with normal household waste
(2012/19/EU) (Fig. 29).
-Follow your country's rules for the separate collection of electrical and electronic products. Correct
disposal helps prevent negative consequences for the environment and human health.
16 English

Dansk
Introduktion
Denne kaffemaskinen er velegnet til tilberedning af 1 eller 2 kopper espresso, og den er udstyret med
en drejelig dyse til damp og varmt vand. Kontrolelementerne foran på maskinen er markeret med
letlæselige symboler. Maskinen er blevet designet til brug i hjemmet og er ikke egnet til professionel,
kontinuerlig brug.
Rent koldt vand
Brug rent, koldt vand hver dag. Hvis du ikke har brugt kaffemaskinen i en dag, skal du skylle den
igennem med rent, koldt vand, før du bruger den igen. Du skyller maskinen igennem ved at fylde
vandtanken med rent, koldt vand, sætte en skål eller 2 kopper under kaffeudløbet og brygge varmt
vand, indtil vandtanken er tom.
Energibesparelse
Maskinerne RI8437, RI8435 og RI8433 er udstyret med en funktionen til automatisk slukning for at
spare energi. Funktionen til automatisk slukning aktiveres, 30 minutter efter at hovedkontakten
indstilles til "I". Du kan tænde maskinen igen ved at sætte hovedkontakten tilbage til "I".
Vigtige sikkerhedsoplysninger
Denne maskine er udstyret med sikkerhedsfunktioner. Læs og følg dog sikkerhedsinstruktionerne
omhyggeligt, og brug kun maskinen som beskrevet i denne brugervejledning for at undgå utilsigtede
skader på personer eller ting som følge af ukorrekt brug af maskinen. Gem dette sikkerhedshæfte til
senere brug.
Advarsel
-Kontrollér, om den angivne netspænding på maskinen svarer til
den lokale netspænding, før du slutter strøm til apparatet.
-Maskinen skal sluttes til en stikkontakt med jordforbindelse.
-Lad aldrig ledningen hænge ud over kanten af et bord eller
komme i kontakt med varme overflader.
-For at undgå faren for elektrisk stød må du aldrig nedsænke
netledningen i vand.
-Hvis netledningen beskadiges, må den kun udskiftes af Gaggia, et
autoriseret Gaggia-serviceværksted eller en tilsvarende
kvalificeret fagmand for at undgå enhver risiko.
-Stikket på netledningen må ikke komme i kontakt med væske.
-For at undgå fare for forbrændinger skal kropsdele holdes væk fra
de stråler med varmt vand, som maskinen producerer.
-Rør ikke ved de varme overflader. Brug maskinens håndtag og
knapper.
17
Dansk

-Sluk for maskinen på hovedkontakten på bagsiden, og tag
netstikket ud af stikkontakten:
-Hvis der opstår en funktionsfejl.
-Hvis du ikke skal bruge apparatet i lang tid.
-Før maskinen rengøres.
-Træk i stikket, ikke i ledningen.
-Rør ikke ved det netstikket med våde hænder.
-Brug aldrig maskinen, hvis netstik, netledning eller selve maskinen
er beskadiget..
-Du må ikke foretage ændringer i maskinen eller maskinens
netledning.
-For at undgå fare må reparationer må kun udføres af en
forhandler, der ergodkendt af Gaggia.
-Maskinen må ikke bruges af børn under 8 år.
-Denne maskine kan bruges af børn fra 8 år og opefter og personer
med reducerede fysiske, sensoriske eller mentale evner eller
manglende erfaring og viden, hvis de er blevet instrueret i sikker
brug af maskinen og forstår de medfølgende risici.
-Rengøring og vedligeholdelse må ikke foretages af børn,
medmindre de er over 8 år gamle og under opsyn.
-Hold maskinen, dens tilbehør og ledning utilgængelig for børn
under 8 år.
-Apparatet skal holdes uden for børns rækkevidde for at sikre, at
de ikke kan komme til at lege med maskinen.
-Vær forsigtig, når du dispenserer varmt vand. Dispensering kan
være efterfulgt af små stråler varmt vand. Vent, indstil
dispenseringscyklussen er færdig, før du fjerner
varmtvandsudløbet.
-For at undgå fare for forbrændinger skal du være opmærksom på,
at der før dispenseringen kan komme små stråler varmt vand. Rør
aldrig ved den klassiske mælkeskummer med de bare hænder, da
den kan blive meget varm.
18 Dansk

-Brug kun denne espressomaskine til det formål, den er beregnet
til, for at undgå potentielle skader.
Forsigtig
-Indlever altid maskinen til et servicecenter godkendt af Gaggia for
undersøgelse eller reparation. Forsøg ikke at reparere maskinen
selv, da din garanti ellers bliver ugyldig.
-Maskinen er kun beregnet til normal anvendelse i hjemmet. Det er
ikke beregnet til brug i miljøer som f.eks. personalekøkkener i
butikker, på kontorer, på gårde eller andre arbejdspladser. Det er
heller ikke beregnet til brug af kunder på hoteller, moteller, bed
and breakfast eller andre beboelsesmiljøer.
-Stil altid maskinen på et fladt og stabilt underlag. Den skal altid
være placeret opretstående, også under transport..
-Stil ikke maskinen på en varmeplade eller direkte ved siden af en
varm ovn, et varmeapparat eller lignende varmekilder.
-Når du rengører maskinen, skal du lade den køle ned, før du
indsætter eller fjerner dele. Varmefladen kan indeholde restvarme
efter brug.
-Fyld aldrig vandtanken med varmt vand eller danskvand, da det
kan beskadige vandtanken og maskinen.
-Brug aldrig skuresvampe eller skrappe rengøringsmidler såsom
rensebenzin eller acetone til rengøring af apparatet. Bare brug en
blød klud, der er fugtet med vand.
-Afkalk maskinen hver 3. måned. Hvis der ikke udføres afkalkning,
vil maskinen holde op med at fungere korrekt. I sådanne tilfælde
er reparation ikke omfattet af garantien.
-Maskinen må ikke opbevares ved temperaturer under 0°C. Hvis
der er vand i opvarmningssystemet kan det fryse og forårsage
skader.
-Efterlad ikke vand i vandtanken, når maskinen ikke skal bruges i
længere tid. Vandet kan blive snavset. Brug rent vand, hver gang
du bruger maskinen.
19
Dansk

-Brug aldrig tilbehør eller dele fra andre producenter eller
tilbehør/dele, som ikkespecifikt er anbefalet af Gaggia Garantien
bortfalder, hvis du bruger sådant tilbehør eller sådanne dele.
-Regelmæssig rengøring og vedligeholdelse forlænger maskinens
levetid og sikrer optimal kvalitet og kaffesmag.
-Maskinen udsættes løbende for fugt, kaffe og kalk. Det er derfor
meget vigtig at rengøre og vedligeholde maskinen regelmæssigt
som beskrevet i brugervejledningen og vist på webstedet. Hvis du
ikke udfører disse rengørings- og vedligeholdelsesprocedurer, kan
maskinen med tiden ophøre med at fungere. I sådanne tilfælde er
reparation ikke omfattet af garantien.
-Drik aldrig den opløsning, der afgives ved afkalkningsprocessen.
-Maskinen må ikke placeres i et skab, når det er i brug.
-Når du har skummet mælk, skal du hurtigt rengøre den klassiske
mælkeskummer ved at dispensere en lille mængde varmt vand i
en beholder. Fjern derefter den udvendige del af den klassiske
mælkeskummer, og vask den med lunkent vand.
-Hæld aldrig andre væsker end rent, koldt vand i vandtanken.
-Den tryksatte filterholder må ikke kommes i opvaskemaskinen.
Dette vil beskadige den tryksatte filterholder.
Elektromagnetiske felter (EMF)
Maskinen overholder alle branchens gældende standarder og regler angående eksponering for
elektromagnetiske felter.
Oversigt over maskinen
1 Strømindikator
2 Lysindikator når damp er klar
3 Lysindikator når maskinen er klar
4 Valgknap
5 Filter til malet kaffe
6 Tryksat filterholder
7 Bryggeenhed
8 Låg til drypbakke (kun nogle modeller)
9 Drypbakke
10 Brugergrænseflade
11 Kopholderstøtte
12 Vandtank
13 Låg over vandtank
14 Måleske til malet kaffe
20 Dansk