Galvin Specialised CliniLever Lead Safe TM-SHWX Instruction sheet

Version 1,14th April 2020, 1 of 4
CliniLever®Lead Safe™Stainless Steel Shower Mixer
PRODUCT CODES:
TM-SHWX
SPECIFICATIONS
Lead Safe™stainless steel construction
Easy temperature blending and operation to ensure comfort and safety for the user
Low maintenance
Clean hygienic design
IMPORTANT: All CliniLever®Shower Mixers are tested in accordance with AS/NZS 3718 and leave our
premises in good working order.
As ‘lead free’ is not currently defined by low in Australia and New Zealand, we have based our definition of Lead Safe™ on the requirements of s1417 of the USA’s Safe Drinking Water Act (SDWA)
and the relevant US standards NSF61 / NSF372. The SDWA defines ‘lead free’ as “not more than a weighted average of 0.25% lead when used with respect to the wetted surface of pipes, pipe fittings,
plumbing fittings and fixtures”.
TECHNICAL DATA
Inlet
½” BSP - Female
Outlet
½“ BSP - Female
Headwork
Ceramic Disc
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
80
Nominal Flow Rate (LPM)
N/A
Construction
Stainless Steel
Finish
Stainless Steel
NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without notice.

Version 3, 7 May 2020, Page 2of 4
Version 1,14th April 2020, 2 of 4
DIMENSIONS
INSTALLATION
INSTALLATION COMPLIANCE: Galvin Engineering products must be installed in accordance with these
installation instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements.
Water and/or electrical supply conditions must also comply to the applicable national and/or state standards.
Failing to comply with these provisions shall void the product warranty and may affect the performance of the
product.
1. Remove Handle
Remove the indicator button as shown.
Using a hex key, remove the grub screw.
2. Remove Handle & Flange
Remove the handle.
Carefully remove flange from the mixer
assembly.
Care should be taken to avoid scratching the
mixer body.
Rough-in Dimensions
Indicator Button

Version 3, 7 May 2020, Page 3of 4
Version 1, 7 May 2020, 3 of 4
zVersion 1, 7 May 2020, 3 of 4
Version 1, 7 May 2020, 3 of 4
3. Secure Mixer Body
To allow proper fitment of the wall flange,
allow a gap between 2mm & 7mm (as
shown) between the finished wall and the
rear of the main body.
Secure the mixer body using the mounting
points.
4. Fit Water Connections
Ensure water supply lines are flushed before
connecting.
Fit the water connections as shown.
Ensure thread tape/sealant is used.
Note: This wall shower is not fitted with a flow
restrictor. Never operate without a flow restrictor, as
outlet will deliver full mains pressure with
unrestricted flow.
5. Fit Handle & Flange
Re-fit handle & flange ensuring care is taken
to avoid scratching the mixer body.
6. Secure Handle & Fit Indicator Button
Using the supplied hex key, fit the grub screw
as shown and secure the handle.
Fit the indicator button as shown.
7. Test
Once the shower mixer has been fitted, turn on mains water and check for leaks and correct
operation.
Mounting point
Mixed water outlet
Cold water inlet
Hot water inlet

Version 3, 7 May 2020, Page 4of 4
Version 1, 7 May 2020, 4 of 4
zVersion 1, 7 May 2020, 4 of 4
Version 1, 7 May 2020, 4 of 4
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Wall shower is dripping water
Headworks are worn or
damaged
Remove and inspect the headworks,
remove debris and/or replace o-rings or
parts if damaged
Leak from behind body
Insufficient sealant
Apply more thread tape or sealant to
create a better seal
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in the
manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective
products manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s
warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.