Galvin Specialised Ezy-Drink TD45C Instruction sheet

Version 1, 31 October 2016, Page 1of 4
Ezy-Drink®Remote Bubbler Tapware
PRODUCT CODES:
- TD45C
- TD90C
SPECIFICATIONS
−Drinking taps are designed to operate at full mains pressure.
−Rubber and metal mouthguards are designed to help protect teeth when drinking.
−Rubber mouthguard is resistant to fungal and bacterial attack and has a high resistance to sunlight.
−Vandal resistant handle.
−Adjustable built-in flow restrictor.
IMPORTANT: All Ezy-Drink
®
Remote Bubbler taps are tested in accordance with AS/NZS 3718 and leave our
premises in good working order.
TECHNICAL DATA
Inlet 15BSP - Female
Outlet Rubber / metal mouth guard
Headwork Cam Action
Working Pressure Range (kPa) Min 50
Max 500
Maximum Working Temperature (°C) Min 5
Max 70
Nominal Flow Rate (LPM) 4.5
Finish Chrome
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without notice.
PRE-INSTALLATION
MOUNTING DETAILS – HOLE CENTRES
−TD90C - If the mounting holes do not already exist, mark
out and drill the holes in the wall/sheet, as shown in
rough-in dimensions.
Note: Before installation, all lines must be flushed. We
recommend that a line strainer be installed prior to drinking taps
to eliminate any foreign material.
TOOLS REQUIRED
−Power drill
−Spanner or adjustable crescent
−Screw driver
50.5
TO SUIT
SCREWS
USED

Version 1, 31 October 2016, Page 2of 4
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions and
in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical supply
conditions must also comply to the applicable national and/or state standards. Failing to comply with these
provisions shall void the product warranty and may affect the performance of the product.
1. Fit tap assembly
−The drinking taps are fitted with flow restrictors.
−When applying thread tape or sealant to the
inlet, ensure the opening is not obscured.
Failure to do so may restrict or block the flow
restrictor, affecting the flow of water.
2. Secure the body
−Secure the body with supplied screws.
−Ensure outlet is 15° angled.
3. Testing
−Once the drinking tap has been installed and tested for leaks, the water height must be adjusted to suit the
available pressure.
−To adjust water flow
1. Remove the blanking screw 
2. Adjust the water height by turning the regulator screw 
3. Replace blanking screw
Note: The full range from minimum flow to maximum flow is only ¼ turn

Version 1, 31 October 2016, Page 3of 4
TROUBLESHOOTING
PROBLEM CAUSE RECTIFICATION
Inconsistent flow Blocked top assembly Remove top assembly and clean
Water is not flowing from tap Water is turned off Turn on water
Blocked flow restrictor Remove restrictor and clean
Continuous flow Top assembly loose or internally
obstructed or damaged Remove top assembly, clean with water and re-grease spindle if required
Rate of flow inadequate The flow regulator screw may
not be adjusted correctly Remove blanking screw and adjust flow regulating screw as described
Button hard to press The mains pressure may be too
great Reduce to below 500kPa (70PSI). Regrease spindle if required

Version 1, 26 October 2016, Page 4of 4
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty Ltd.
With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied. Galvin
Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but not limited
to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download from
www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free from
operational defects in workmanship and materials for the warranty period as shown on the schedule in the
manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective
products manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s warranty
are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property
which is damaged if this product does not work properly, other costs resulting from labour charges, delays,
vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical,
electrical or any other circumstances over which Galvin Engineering has no control. This warranty shall be
invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the
product.