Galvin Specialised Ezy-Drink Lead Safe Instruction sheet

Version 1,15th March 2021, Page 1of 4
Ezy-Drink®Lead Safe™ Remote Electronic
Drinking Bubbler Tap - Battery
PRODUCT CODES:
- 170.81.11.00
SPECIFICATIONS
−Drinking taps are designed to operate at full mains pressure.
−The rubber mouthguard is resistant to fungal and bacterial attack and has a high resistance to sunlight.
−Adjustable built-in flow restrictor.
IMPORTANT: All Ezy-Drink®remote bubbler taps are tested in accordance with AS/NZS 3718 and leave
our premises in good working order.
As ‘lead free’ is not currently defined by low in Australia and New Zealand, we have based our definition of Lead Safe™ on the requirements of s1417 of the USA’s Safe Drinking Water Act
(SDWA) and the relevant US standards NSF61 / NSF372. The SDWA defines ‘lead free’ as “not more than a weighted average of 0.25% lead when used with respect to the wetted surface of
pipes, pipe fittings, plumbing fittings and fixtures”.
TECHNICAL DATA
Inlet
½”BSP - Female
Outlet
Rubber mouthguard
Headwork
Piezo Activation
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
60
Nominal Flow Rate (LPM)
1.44
Solenoid
Input Voltage
6 V DC
Power Consumption
-
Cable length
3.2m
Connection
Inlet
1/2” BSP - Female
Outlet
1/2” BSP - Male
Pressure Range
(kPa)
Min
50
Max
500
Temperature
(°C)
Min
5
Max
60
Finish
Chrome
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without
notice.

Version 1,15th March 2021, Page 2of 4
TOOLS REQUIRED
−Power drill
−Spanner or adjustable crescent
−Screw driver
PRE-INSTALLATION - MOUNTING DETAILS
−If the mounting holes do not already exist, mark out and drill
the holes in the bench/trough, as shown in rough-in
dimensions.
Note: Supplied flexi hose length is 225mm long.
Maximum distance between the solenoid and outlet is 210mm.
Note: Before installation, all lines must be flushed.
We recommend that a line strainer be installed prior to drinking
taps to eliminate any foreign material.
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical
supply conditions must also comply to the applicable national and/or state standards. Failing to comply with these
provisions shall void the product warranty and may affect the performance of the product.
1. Disassemble piezo button and outlet
−Remove back nut and cup washer from the
outlet assembly
−Remove back nut from piezo button
2. Fit mouthguard outlet
−Fit the mouthguard outlet into the trough.
−Ensure the sealing rubber washers are placed
underneath the mouthguard outlet body.
−Secure underneath with the supplied cup washer and
back nut.
−Take care not to over-tighten
210 MAX

Version 1,15th March 2021, Page 3of 4
3. Fit Piezo Button
−Install piezo button and connect it to the
electronic control unit.
4. Connect, Solenoid and Battery
−Connect Piezo button, the solenoid and the battery to
the eletronic control unit.
−The unit was supplied with 2 x 3.2metre extension
leads for connecting to battery and solenoid.
5. Fit Solenoid and Outlet
−Fix the solenoid in position ensuring that
the solenoid coil is not facing
downwards.
−Fit flexi hose to solenoid and water supply.
−Fit flexi hose to outlet
6. Testing
−Once the drinking tap has been installed and tested
for leaks, the water height may be adjusted to suit the
available pressure.
−To adjust water flow (if required)
1. Remove the blanking screw
2. Adjust the water flow by turning the regulating
screw
3. Replace blanking screw
Note: The full range from minimum flow to
maximum flow is only ¼ turn
Solenoid
Coil
Water
Supply
Blanking
Screw
Regulating
Screw

Version 1,15th March 2021, Page 4of 4
SET WATER FLOW DURATION
Contact Galvin Specialised for information regarding changing flow duration.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Water is not flowing from
tap
Water is turned off
Turn on water
Blocked flow regulating screw
Remove flow regulating screw and clean
Rate of flow inadequate
The flow regulator screw may
not be adjusted correctly
Remove blanking screw and adjust flow
regulating screw as described above
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty Ltd.
With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied. Galvin
Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but not
limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download from
www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free from
operational defects in workmanship and materials for the warranty period as shown on the schedule in the
manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective
products manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s
warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.