Galvin Specialised Ezy-Drink TD45L Instruction sheet

Version 2, 8 June 2017, Page 1of 4
Ezy-Drink®Lever Bubbler Tapware
PRODUCT CODES:
- TD45L
- TD90L
SPECIFICATIONS
−Drinking taps are designed to operate at full mains pressure.
−Rubber and metal mouthguards are designed to help protect teeth when drinking.
−Rubber mouthguard is resistant to fungal and bacterial attack and has a high resistance to sunlight.
−Vandal resistant handle.
−Adjustable built-in flow restrictor.
IMPORTANT: All Ezy-Drink®Lever Bubbler taps are tested in accordance with AS/NZS 3718 and leave
our premises in good working order.
TECHNICAL DATA
Inlet ½” BSP - Female
Outlet Rubber / metal mouthguard
Headwork Lever action
Working Pressure Range (kPa) Min 50
Max 500
Working Temperature Range (°C) Min 5
Max 60
Nominal Flow Rate (LPM) 2
Finish Chrome
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without
notice.
TOOLS REQUIRED
−Power drill
−Spanner or adjustable crescent
−Screw driver

Version 2, 8 June 2017, Page 2of 4
PRE-INSTALLATION - MOUNTING DETAILS
−TD90L - If the mounting holes do
not already exist, mark out and drill
the holes in the wall/sheet, as
shown in rough-in dimensions.
Note: Before installation, all lines must
be flushed. We recommend that a line
strainer be installed prior to drinking
taps to eliminate any foreign material.
TD45L
TD90L
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation
instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water
and/or electrical supply conditions must also comply to the applicable national and/or state standards.
Failing to comply with these provisions shall void the product warranty and may affect the performance of
the product.
1. Fit tap assembly
−When applying thread tape or sealant to
the inlet, ensure the opening is not
obscured. Failure to do so may restrict or
block the flow restrictor, affecting the flow
of water.
2. Secure the body
−Secure the body with supplied screws.
−Ensure outlet is 15° angled.
70°
120
1/2" BSP
ASSEMBLY
(SIDE VIEW AS
INSTALLED)
50.5
TO SUIT
SCREWS
USED
135 NOM
1/2" BSP
ASSEMBLY
(AS SEEN BY USER)
15°
64

Version 2, 8 June 2017, Page 3of 4
3. Testing
−Once the drinking tap has been installed and tested for leaks, the water height must be adjusted to suit
the available pressure.
−To adjust water flow
1. Remove the blanking screw 
2. Adjust the water height by turning the regulator screw 
3. Replace blanking screw
Note: The full range from minimum flow to maximum flow is only ¼ turn
TROUBLESHOOTING
PROBLEM CAUSE RECTIFICATION
Inconsistent flow Blocked top assembly Remove top assembly and clean
Water is not flowing from tap Water is turned off Turn on water
Blocked flow restrictor Remove restrictor and clean
Continuous flow Top assembly loose or internally
obstructed or damaged Remove top assembly, clean with water and re-grease spindle if required
Rate of flow inadequate The flow regulator screw may
not be adjusted correctly Remove blanking screw and adjust flow regulating screw as described
Button hard to press The mains pressure may be too
great Reduce to below 500kPa (70PSI). Regrease spindle if required
BLANKING SCREW

Version 2, 31 October 2016, Page 4of 4
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including
but not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy
for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.