Galvin Specialised Ezy-Drink Lead Safe CP-BS Instruction sheet

Version 1, 27th October 2020 Page 1of 4
Ezy-Drink®CP-BS Lead Safe™ Remote Push
Button Top Assembly
PRODUCT CODES:
- 170.93.43.00
SPECIFICATIONS
−Self-closing push button valve
−Chrome plate finish for easy cleaning and added durability
−Made from Lead Safe™brass
IMPORTANT: The push button has only two modes. Fully open or closed. Therefore, flow restriction
must be fitted preceding the valve bodies to adjust the flow rate to the desired level.
IMPORTANT: All Ezy-Drink®remote top assemblies are tested in accordance with AS/NZS 3718 and leave
our premises in good working order.
As ‘lead free’ is not currently defined by low in Australia and New Zealand, we have based our definition of Lead Safe™ on the requirements of s1417 of the USA’s Safe Drinking Water Act
(SDWA) and the relevant US standards NSF61 / NSF372. The SDWA defines ‘lead free’ as “not more than a weighted average of 0.25% lead when used with respect to the wetted surface of
pipes, pipe fittings, plumbing fittings and fixtures”.
TECHNICAL DATA
Inlet
G 5/8” BSP - Male
Outlet
N/A
Headwork
Push Button
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
60
Nominal Flow Rate (LPM)
N/A
Finish
Chrome
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without
notice.
TOOLS REQUIRED
−Spanner or adjustable crescent
−Screwdriver
−Hex key (supplied)

v
Version 1, 27th October 2020 Page 2of 4
PRE-INSTALLATION
NOTE: Before installation, all lines must be
flushed. We recommend that a line strainer be
installed prior to Push Button Tapware to eliminate
any foreign material.
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical
supply conditions must also comply to the applicable national and/or state standards. Failing to comply with these
provisions shall void the product warranty and may affect the performance of the product.
1. Disassemble & Remove Existing
−Ensure the inlet body is secure as it will lose its
support once the push button assembly has
been removed.
−Remove existing push button assembly from the
inlet body (not supplied) as shown.
2. Fit Replacement Top Assembly
−Check & clean the inlet prior to fitting the replacement
assembly.
−Fit new push button assembly as shown.
Not Supplied
Not Supplied

v
Version 1, 27th October 2020 Page 3of 4
3. Secure Inlet Body
−Tighten the screws on the inlet body as shown. Do not overtighten.
−Once fitted, check installation for leaks and correct operation.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Inconsistent flow
Blocked top assembly
Remove top assembly and clean
Water is not flowing from tap
Water is turned off
Turn on water
Continuous flow
Top assembly loose or
internally obstructed or
damaged
Remove top assembly, clean with water
and re-grease spindle if required
Button hard to press
The mains pressure may be
too great
Reduce to below 500kPa (70PSI). Re-
grease spindle if required
Not Supplied

v
Version 1, 27th October 2020 Page 4of 4
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including
but not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy
for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.