Galvin Specialised Ezy-Drink TD45XP Instruction sheet

Version 1, 15 April 2019, Page 1of 4
Ezy-Drink®Lead Free SS316
45° Push Button
Drinking Bubbler Tap
PRODUCT CODES:
- TD45XP
SPECIFICATIONS
−The innovative design and 316 Stainless Steel construction ensures there is no risk of lead leaching
into the water from the tapware.
−Drinking taps are designed to operate at full mains pressure.
−Rubber and metal mouthguards are designed to help protect teeth when drinking.
−Rubber mouthguard is resistant to fungal and bacterial attack and has a high resistance to sunlight.
−Vandal resistant handle.
−Adjustable built-in flow restrictor.
IMPORTANT: All Ezy-Drink®push button drinking taps are tested in accordance with AS/NZS 3718 and leave our
premises in good working order.
TECHNICAL DATA
Inlet
½” BSP - Female
Outlet
Rubber mouthguard
Headwork
Push button
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
60
Nominal Flow Rate (LPM)
2
Construction
Stainless Steel
Finish
Satin
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without notice.
TOOLS REQUIRED
−Power drill
−Spanner or adjustable crescent
−Screw driver

Version 1, 15 April 2019, Page 2of 4
PRE-INSTALLATION - MOUNTING DETAILS
Note: Before installation, all lines must be flushed. We recommend that a line strainer be installed prior to drinking
taps to eliminate any foreign material.
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical
supply conditions must also comply to the applicable national and/or state standards. Failing to comply with
these provisions shall void the product warranty and may affect the performance of the product.
1. Fit tap assembly
−Fit tap assembly to ½” BSP male connection
using thread tape or sealant to seal the inlet.
Ensure position is as shown; mouthguard to
be facing upward.
−Note: When applying thread tape or sealant
at the inlet, ensure the inlet is not obscured.
This is to prevent excess thread tape or
sealant blocking the flow regulator, affecting
the flow of water.
2. Testing
−Once the drinking tap has been installed and
tested for leaks, the water height must be
adjusted to suit the available pressure.
−To adjust water flow:
1. Remove the blanking screw 
2. Adjust the water height by turning the
regulator screw 
3. Replace blanking screw.
−Note: The full range from minimum flow to
maximum flow is only ¼ turn.

Version 1, 15 April 2019, Page 3of 4
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Inconsistent flow
Blocked top assembly
Remove top assembly and clean
Water is not flowing from tap
Water is turned off
Turn on water
Blocked flow restrictor
Remove restrictor and clean
Continuous flow
Top assembly loose or internally
obstructed or damaged
Remove top assembly, clean with water
and re-grease spindle if required
Rate of flow inadequate
The flow regulator screw may
not be adjusted correctly
Remove blanking screw and adjust flow
regulating screw as described
Button hard to press
The mains pressure may be too
great
Reduce to below 500kPa (70PSI)
Regrease spindle if required

Version 2, 15 April 2019, Page 4of 4
Blanking Screw
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including
but not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy
for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.