Galvin Specialised Ezy-Push SS316 Instruction sheet

Version 3,15th July 2020, Page 1of 4
Ezy-Push®SS316 Lead Safe Timeflow Push Button
Bib Tap –6 Sec
PRODUCT CODES:
- 368667X
SPECIFICATIONS
Time flow taps are designed to operate at full mains pressure.
The valve has a unique self-closing operation.
The taps are made of lead free stainless steel.
Clean hygienic design.
Water saving.
Low maintenance and easy to operate.
Supplied with hot (red), warm (yellow) and cold (blue) buttons depending on the requirement.
Smooth round designs to facilitate easy cleaning and help reduce dirt and bacteria growth.
Note: Time is based on 500kPa, @ 22 degrees Celsius. Time will vary plus or minus 30% based on water
temperatures, pressures, flow rates and water quality.
IMPORTANT: All Ezy-Push®Time Flow Bib Taps are tested in accordance with AS/NZS 3718 and leave our
premises in good working order. Time may vary due to changes in temperature, pressure, flow rate and water
quantity.
TECHNICAL DATA
Inlet
½” BSP - Male
Outlet
Aerator
Headwork
Time Flow Cartridge
Working Pressure Range (kPa)
Min
200
Max
500
Maximum Working Temperature (°C)
Min
5
Max
65
Nominal Flow Rate (LPM)
4.4
Construction
Stainless Steel
Finish
Stainless Steel
NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without
notice.
TOOLS REQUIRED
Power drill
Spanner or adjustable crescent
Screw driver

Version 3,15th July 2020, Page 2of 4
PRE-INSTALLATION
MOUNTING DETAILS
Note: Before installation, all lines must be flushed. We recommend that a line strainer be installed prior to
Ezy-Push Time Flow Bib taps to eliminate any foreign material.
INSTALLATION
IMPORTANT: Galvin Engineering products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical
supply conditions must also comply to the applicable national and/or state standards. Failing to comply with
these provisions shall void the product warranty and may affect the performance of the product.
1. Fit tap assembly
Time flow taps are fitted with flow
restrictors.
When applying thread tape or sealant to
the inlet, ensure the opening is not
obscured. Failure to do so may restrict
or block the flow restrictor, affecting the
flow of water.
2. Replacing flow restrictor (if required) and fitting
water temperature indicator
Major restrictions to the supply pressure may
effect the water stream and the flow restrictor
may need replacing with a flow restrictor of
greater capacity to increse the flow. However,
using a different flow restrictor will void the 6
star rating.
Never operate without a flow restrictor, as Ezy-
Push®Time Flow Deluxe Bib taps will deliver
full mains pressure with unrestricted flow.
Fit the appropriate water temperature
indicator (Cold, Hot or Warm).
Flow Regulator

Version 3,15th July 2020, Page 3of 4
3. Testing
Once fitted, connect the water lines & turn on water.
Check for leaks and correct operation.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Water is not flowing or
inconsistent flow.
Blocked flow restrictor / dirt in the
cartridge / water supply not on.
Remove flow regulator from outlet and
remove debris. Install an inline strainer to
stop further blockages. Ensure water
supply is turned on.
Continous flow of
water.
Top assembly cartridge loose or
internally obstructed or damaged.
Remove cartridge, clean with water and re-
grease spindle if required.
Rate of flow
inadequate.
The flow restrictor may not be
satisfactory due to inadequate supply
pressure.
Remove flow restrictor and replace with a
flow restrictor of different capacity to suit
(available from Galvin Engineering).
Button hard to activate.
Mains pressure may be too high.
Reduce mains pressure to below 500kPa.
Water shuts off upon
releasing the button.
Small spring at the bottom of the
cartridge piston dislodged.
Relocate spring & regrease spindle if
required.

Version 3,15th July 2020, Page 4of 4
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including
but not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy
for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.