Galvin Specialised Ezy-Wash TF83HJS Instruction sheet

Version 1, 11 July 2017, Page 1 of 5
Ezy-Wash® Pre-Rinse Tapware
PRODUCT CODE:
- TF83HJS
- TF83HJP
TF83HJS TF83HJP
SPECIFICATIONS
 Galvin Specialised recommends the installation of strainers and pressure reducing valves prior to installing
the pre-rinse unit to ensure clean consistent water supply. Debris or poor water quality could cause the
trigger to seize or fail to seal.
 This pre-rinse unit has a 6 star WELS rating, the Pot Filler attachments are 0 star to allow fast pot filling.
 The hose on these units is not suitable for potable water and should only be used for washing down/
cleaning purposes.
TECHNICAL DATA
Inlet ½” BSP – Male
Outlet TF83HJS Trigger Spray
TF83HJP Trigger Spray & Pot Filler
Headworks TF83HJS Jumper Valve
TF83HJP Jumper Valve
Working Pressure Range (kPa)
Min 100
Max 500
Working Temperature Range (°C) Min 5
Max 65
Nominal Flow Rate (LPM) TF83HJS 3.5
TF83HJP 15
Finish Chrome
NOTE: Galvin Specialised continually strives to improve their products. Specifications may change without
notice. Higher temperature or pressures could result in premature failure and void the manufacturer’s warranty.
TOOLS REQUIRED
 Adjustable spanner
 Hex key
 Power drill

Version 1, 11 July 2017, Page 2 of 5
PRE-INSTALLATION
Body:
 If the mounting holes do not already exist, mark
out and drill the holes in the bench, as shown.
 This model is a dual inlet unit requiring a hole
diameters of 23mm - 26mm, 205mm apart. Ensure
70mm minimum between wall and hole center as
shown “A”.
 Maximum bench thickness is 55mm.
Wall Bracket:
 Mark out the three (3) holes for mounting the wall
bracket assembly at a height of between 420mm
min - 510mm max directly up from the bench. Cut
out or drill as shown in the image. (Supplied
fasteners may not be suitable for the mounting
surface. If this is the case, suitable fasteners will
need to be sourced by the installer)
Note: We recommend the wall bracket is installed
at the maximum of 510mm. The wall bracket can be
mounted lower at a height of up to 90mm below the
circlip. However, the further it is mounted away
from the circlip, the more the stability of the unit is
compromised.
MOUNTING DETAILS
TF83HJS – Assembly
TF83HJP - Assembly

Version 1, 11 July 2017, Page 3 of 5
INSTALLATION
INSTALLATION COMPLIANCE: Galvin Specialised products must be installed in accordance with these
installation instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements.
Water and/or electrical supply conditions must also comply to the applicable national and/or state standards.
Failing to comply with these provisions shall void the product warranty and may affect the performance of the
product.
1. Measure and cut support rod
 Measure the distance between the wall
mounting surface and the centre line of the
drilled hole in the bench/trough (dimension “A”).
 Take dimensions “A” and subtract 16mm. This
is the required length of the support rod
(Required support rod length = A-16mm).
 Cut the support rod accordingly; ensure the
threaded end is NOT cut off.
Note: Distance “A” must be no less than 70mm.
The support rod length can be 70mm min. to
285mm max. (If it is more than 285mm, an
extension support rod must be purchased)
2. Fit wall bracket
 Secure to the wall bracket to the wall.
 Supplied fasteners may not be suitable for the
mounting surface. If so, suitable fasteners will need
to be sourced.
Note: The wall flange must be mounted with three
screws for stability and strength. This is critical,
failure to do this may void the warranty.
TF83HJS TF83HJP
3. Fit support rod
 If pot filler kit (TF83HJP) has been
purchased, it must be attached to the pre-
rinse unit prior to fitting the support rod
to the riser. Refer to the installation
instruction supplied with the Pot filler.
 Screw support rod into the riser hook and
ensure it is not fully tightened.
4. Fit pre-rinse riser assembly
1. Fit compression nut to support rod, followed by
the compression cone and locate the support
rod into wall bracket.
2. Fit the pre-rinse riser assembly through the
drilled hole on the bench.

Version 1, 11 July 2017, Page 4 of 5
TF83HJS TF83HJP
5. Secure pre-rinse assembly
 Secure Pre-Rinse assembly with the
supplied flanged back nut; ensure the
sealing rubber washer is placed
underneath the Pre-Rinse body flange.
6. Secure support rod
1. Fasten support rod securely against CP riser.
2. Tighten compression nut on wall bracket to
secure the support rod. The rod is now rigid.
TF83HJS TF83HJP
7. Fit hose
 Fit hose to the Pre-Rinse riser with a
spanner.
 Ensure supplied fiber washer is fitted inside
of hose nut.
8. Test unit
 Once all fittings have been tightened securely
and the unit has been connected to the mains
water, the unit must be tested for any leaks.
OPERATING INSTRUCTIONS
 The isolation or main taps must be turned OFF whilst the unit is not in use so that the unit is not under mains
pressure when unsupervised. Flood damage may occur if a failure occurs whilst the unit is under mains
pressure. (warranty is void in this instance).
 Galvin Specialised recommends the handpiece be removed periodically for servicing by a qualified plumber.

Version 1, 11 July 2017, Page 5 of 5
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in the
manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective
products manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s
warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product