Galvin Specialised Ezy-Drink CP-BS TD15EB Instruction sheet

Version 1, 16th June, Page 1of 4
Ezy-Drink® CP-BS Remote Electronic Drinking
Bubbler Tap - Battery
PRODUCT CODES:
- TD15EB
SPECIFICATIONS
−Drinking taps are designed to operate at full mains pressure.
−The rubber mouthguard is resistant to fungal and bacterial attack and has a high resistance to sunlight.
−Adjustable built-in flow restrictor.
IMPORTANT: All Ezy-Drink®bubbler taps are tested in accordance with AS/NZS 3718 and leave our
premises in good working order.
TECHNICAL DATA
Inlet
½” BSP - Female
Outlet
Rubber mouthguard
Headwork
Solenoid
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
60
Nominal Flow Rate (LPM)
1.44
Solenoid
Input Voltage
6 V DC
Power Consumption
-
Connection
Inlet
1/2” BSP - Female
Outlet
1/2” BSP - Male
Pressure Range
(kPa)
Min
50
Max
500
Temperature
(°C)
Min
5
Max
60
Finish
Chrome
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without
notice.

Version 1, 16th June, Page 2of 4
TOOLS REQUIRED
−Power drill
−Spanner or adjustable crescent
−Screw driver
PRE-INSTALLATION - MOUNTING DETAILS
−If the mounting holes do not already exist, mark out and drill
the holes in the bench/trough, as shown in rough-in
dimensions.
Note: Supplied flexi hose length is 225mm long.
Note: Before installation, all lines must be flushed.
We recommend that a line strainer be installed prior to drinking
taps to eliminate any foreign material.
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical
supply conditions must also comply to the applicable national and/or state standards. Failing to comply with these
provisions shall void the product warranty and may affect the performance of the product.
1. Disassemble piezo button and outlet
−Remove backnuts and washers as
shown.
2. Fit mouthguard outlet
−Fit the body and mouthguard outlet into the trough.
−Ensure the sealing rubber washers are placed
underneath the mouthguard outlet body.
−Secure underneath with the supplied cup washer and
back nut.
Rough-In Dimensions

Version 1, 16th June, Page 3of 4
3. Fit Piezo Button
−Install piezo button as shown.
−Ensure the correct coloured washer is fitted
underneath the button.
4. Connect Piezo Button, Solenoid and Battery
−Connect Piezo button, the solenoid & the battery to the
eletronic control unit.
−The unit is supplied with 2 x 3.2metre extension leads
for connecting to battery and solenoid.
5. Fit Solenoid and Outlet
−Fit flexi-hose to solenoid outlet and
bubbler.
−Connect water supply to solenoid inlet.
6. Testing
−Once the drinking tap has been installed and tested
for leaks, the water height may be adjusted to suit the
available pressure as shown above.
−To adjust water flow
1. Remove the blanking screw.
2. Adjust the water height by turning the regulator
screw.
3. Once desired height has been achieved, replace
blanking screw.
Note: The full range from minimum flow to maximum flow is
only ¼ turn.
Water
Supply
Blanking Screw
Regulator Screw

Version 1, 16th June, Page 4of 4
SET WATER FLOW DURATION
1.
−Switch the power to the controller off.
After 5 seconds switch the power on.
−Locate the light on the controller.
−Press the piezo button 4 times.
−The green light on the controller
should flash 5 times.
2.
−Once again, push the piezo button 5 times.
−The red light on the controller should now be lit.
−Leave the red light on for the desired flow
duration time.
−Press the button to finish setting the time.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Water is not flowing from
tap
Water is turned off
Turn on water
Blocked flow restrictor
Remove restrictor and clean
Rate of flow inadequate
The flow regulator screw may
not be adjusted correctly
Remove blanking screw and adjust flow
regulating screw as described above
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download from
www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free from
operational defects in workmanship and materials for the warranty period as shown on the schedule in the
manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective
products manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s
warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.
Button
Controller