Galvin Specialised GalvinCare 50197 Instruction sheet

GalvinCare®Mental HealthTapware
PRODUCT CODES:
- 50197
SPECIFICATIONS
This products unique design concept eliminates the institutional look and provides anti-ligature
features and vandal resistant compliance
The paddle design handle allows the diverter to be activated with minimal effort.
The 170mm round faceplate has a polished stainless steel finish for a homely look and can
withstand heavy knocks and bevelled edges provide tight fixing
This item is designed for wall installation
IMPORTANT: All GalvinCare®prison taps are tested in accordance with AS/NZS 3718 and leave our premises
in good working order.
TECHNICAL DATA
Inlet
½” BSP –Male
Outlet
½” BSP –Female
Headwork
Diverter Cartridge
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
90
Finish
Chrome / Polished Stainless Steel
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without
notice.
PRE-INSTALLATION
MOUNTING DETAILS –ROUGH IN & OVERALL DIMENSIONS
Suitable for in-wall mounting
Drill 6.5mm hole as shown for Anti-Rotation pin.
TOOLS REQUIRED
Power drill - Spanner or adjustable crescent

INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical
supply conditions must also comply to the applicable national and/or state standards. Failing to comply with
these provisions shall void the product warranty and may affect the performance of the product.
1. Fit body assembly
Secure body with mounting brackets as indicated, ensure
it is protruding past the finished wall between 6mm
minimum and 16mm maximum.
Brackets are suitable for horizontal and vertical mounting.
It is critical that the centre line of the cartridge spindle is
perpendicular to the finished wall to ensure correct fitment
of the faceplate and flange.
2. Connect water supply
Connect water supply to correct inlets as
shown, ensure a suitable sealing
compound is used
Connect correct outlet connection to
shower outlet.
Note: Water supply should be flushed before
fitting. The use of in-line strainers is highly
recommended.
3. Fit faceplate & flange
Fit supplied o-ring into groove on the back of the flange.
Fit faceplate on to shoulder of flange.
Fit the switch (not supplied) to faceplate.
4. Secure flange
Slide faceplate and flange onto the body.
Secure with three M4 cap screws and lock
washers, ensure the faceplate anti-rotation
pin to be pushed through the 6.5mm
hole.

5. Fit the handle
Fit the nylon insert and handle, ensuring the arrow on the
handle matches the lines on the faceplate when rotated.
Secure the handle with supplied tamper proof screw.
6. Testing
Once fitted all parts & connected with
controller, test body for leaks and correct
operation.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Faceplate does not sit flush on
wall
Diverter not mounted
perpendicular to wall
Remove and re-mount so the body is
perpendicular to finshed wall
Water flow does not match
faceplate markings
Handle not aligned correctly
to faceplate
Remove handle and rotate on the spline
until handle matches faceplate. Re-tighten
Outlet on body not connected
to the correct service outlet
Change outlet connection on body
SERVICE AND MAINTENANCE
1. Turn off water
Turn off the water supply and turn on the tap
handle to release any pressure in the lines
Disconnect the plug from controller
Disconnect cold, hot and inlet water
connections
2. Remove handle assembly
Unscrew tamper proof screw from handle
Pull out handle assembly from the body

3. Remove flange screws
Unscrew the flange screws
4. Remove faceplate (with button) and flange
5. Remove cartridge nut and check cartridge
Unscrew cartridge nut and remove cartridge.
Check the cartridge for wear and damage.
Replace if required with cartridge
replacement available through your supplier
Check and clean the body of all debris
6. Re-assemble
Re-assemble, by reversing steps 5 to 1.
Ensuring sealing compound is used when
connecting water supply and outlet.
Turn on water and check for correct operation
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download from
www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free from
operational defects in workmanship and materials for the warranty period as shown on the schedule in the
manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective
products manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s
warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.