Galvin Specialised CliniLever TCWMC80PC User manual

Version 2, 18 July 2017, Page 1of 4
CliniLever®Healthcare Tapware
PRODUCT CODES:
- TCWMC80PC
- TCWMJ80PC
SPECIFICATIONS
−The CliniLever®product range is primarily used for hand washing applications in hospitals, aged care
facilities, schools and in-home care.
−CliniLever®products provide state of the art features to comply with the latest healthcare guidelines.
−Easy operation dual levers for on/off, hot and cold temperature control simplify hand washing procedures.
−Our highly sought after lever handle design is easily operated with elbows or wrists to avoid hand contact.
−The main body is made of solid dezincification resistant (DR) brass rod, with a DR brass fixed outlet.
−Quick action SBA’s includes brass jumper valve / ceramic cartridge component, with red and blue indicator
button on 80mm lever action handles.
IMPORTANT: All CliniLever®healthcare taps are tested in accordance with AS/NZS 3718 and
leave our premises in good working order.
TECHNICAL DATA
Inlet ½” BSP - Female
Outlet ¾” BSP - Male
Headwork Jumper Valve/Ceramic Disc
Working Pressure Range (kPa) Min 50
Max 500
Working Temperature Range (°C) Jumper Valve/Ceramic Min 5 Jumper Valve Max 80
Ceramic Max 90
Nominal Flow Rate (LPM) N/A
Finish Chrome
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without
notice.
TOOLS REQUIRED
−Power drill
−Spanner
−Hex key
−Thread tape

Version 2, 18 July 2017, Page 2of 4
PRE-INSTALLATION - MOUNTING DETAILS
Wall Spud
−Wall spuds must be 15BSP MI and protrude from the finished wall by no more than 15mm
Note: In some situations a male thread connection on the tap may be more suited. If so, please
contact Galvin Specialised on 1300 514 074.
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation
instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water
and/or electrical supply conditions must also comply to the applicable national and/or state standards.
Failing to comply with these provisions shall void the product warranty and may affect the performance of
the product.
1. Fit washing machine body
−Fit the washing machine body assembly with
the wall flange to the spud and fasten with a
spanner.
−We recommend using thread tape or
equivalent to ensure the connection does not
leak.
−DO NOT tighten the body by using the top
assembly.
2. Fit handle
−Ensure the spindle is in the closed position
and firmly press the CliniLever®lever handle
onto the spindle in the desired orientation.
−Check CliniLever®lever handles for operation.
It should turn freely for a full ¼ turn.
−Secure the handle in position using the
supplied washer and stainless steel cap
screw.

Version 2, 18 July 2017, Page 3of 4
3. Fit water temperature indicator
−Once CliniLever®lever handle is secure, fit
the water temperature indicator.
−Ensure the set is installed with hot and cold
in the correct location.
4.Testing
−Once temperature indicator is fitted, check the
operation of the unit and inspect for any leaks.
TROUBLESHOOTING
PROBLEM CAUSE RECTIFICATION
Taps are dripping water
Jumper valves are worn or damaged Replace jumper valve
Ceramic discs are worn or damaged Remove and inspect SBA. Remove debris and/or replace
SBA if damaged.
Tap seat is damaged Refurbish tap seat using a
reseating tool.
Water is leaking from spindle O-ring on jumper valve spindle is
damaged or worn Replace o-ring
Water is not flowing from tap
Water is turned off Turn water on
Aerator or flow regulator is blocked by
debris
Remove aerator and/or flow
regulator from tap and remove
debris. Install an inline strainer.
Spindle is difficult to turn
(jumper valve) Build up of scale on spindle, spindle worn or o-ring has been damaged
Remove jumper valve, clean and
regrease. Replace o-ring.
Complete SBA may need to be
replaced.
Handle is loose Screw has come loose Tighten handle screw
Flange does not screw down
onto basin/sink surface Tap bodies are set too far out Re-position tap bodies and breach
piece

Version 2, 18 July 2017, Page 4of 4
SERVICE AND MAINTENANCE
JUMPER VALVE TAPWARE CERAMIC CARTRIDGE TAPWARE
1. Turn off the water supply and turn on the tap
handle to drain water from the bodies.
2. Remove the temperature indicator from the
handle.
3. Remove the handle from the tap.
4. Unscrew the top assembly from the body.
5. Check the o-ring on the spindle and the
jumper valve for wear and damage.
Replace if required.
6. Clean the spindle and body of debris.
7. Place a new o-ring (if required) onto the
spindle and re-grease with potable water
approved grease.
8. Re-assemble top assembly. Follow the product
installation guidelines for the relevant product
to re-assembly method.
1. Turn off the water supply and turn on the tap
handle to drain water from the bodies.
2. Remove the temperature indicator from the
handle.
3. Remove the handle from the tap.
4. Unscrew the ceramic head part from the body.
5. Check the o-ring on the ceramic head part for
wear and damage. Replace if required.
6. Clean the head part and the body of any
debris.
7. Replace the cartridge and hand tighten back
into the body.
8. Follow the product installation guidelines for
the relevant product to re-assemble.
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in the
manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective
products manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s
warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.