Galvin Specialised Ezy-Drink TD00L-RM Instruction sheet

Version 2, 31 July 2017, Page 1 of 4
Ezy-Drink® Lever Action Bubbler Tapware
PRODUCT CODES:
- TD00L-RM
- TD00L-LM
SPECIFICATIONS
 Drinking taps are designed to operate at full mains pressure.
 Rubber mouthguard is designed to help protect teeth while drinking.
 Rubber mouthguard is resistant to fungal and bacterial attack and has a high resistance to sunlight.
 Vandal resistant handle
 Adjustable built-in flow restrictor
IMPORTANT: All Ezy-Drink® lever bubbler taps are tested in accordance with AS/NZS 3718 and leave
our premises in good working order.
TECHNICAL DATA
Inlet ½” BSP - Male
Outlet Rubber mouthguard
Headwork Lever action
Working Pressure Range (kPa) Min 50
Max 500
Working Temperature Range (°C) Min 5
Max 60
Nominal Flow Rate (LPM) 2
Finish Chrome
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without
notice.
TOOLS REQUIRED
 Power drill
 Spanner or adjustable crescent
 Screw driver

Version 2, 31 July 2017, Page 2 of 4
PRE-INSTALLATION
MOUNTING DETAILS – HOLE CENTRES
 If the mounting holes do not already exist, mark out and drill the holes in
the bench/trough, as shown in rough-in dimensions.
 Ensure alignment of 5mm hole is as shown, as this will determine the direction of the water flow.
Note: Before installation, all lines must be flushed. We recommend that a line strainer be installed
prior to drinking taps to eliminate any foreign material.
16.0
5.0 DRILL
23mm Min.
26mm Max.

Version 2, 31 July 2017, Page 3 of 4
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or
electrical supply conditions must also comply to the applicable national and/or state standards. Failing to
comply with these provisions shall void the product warranty and may affect the performance of the product.
1. Fit tap assembly
 Fit the outlet into the bench.
 Ensure the rubber sealing washer is
placed underneath the outlet body and
the anti-rotation pin locates properly.
 Secure underneath with the supplied cup
washer and back nut.
2. Flow adjust
 To adjust water flow
1. Remove the blanking screw 
2. Adjust the water height by turning the
regulator screw 
3. Replace blanking screw
Note: The full range from minimum flow to maximum
flow is only ¼ turn
3. Testing
Once the drinking tap has been installed and tested for leaks,
the water height must be adjusted to suit the available
pressure.

Version 2, 31 July 2017, Page 4 of 4
TROUBLESHOOTING
PROBLEM CAUSE RECTIFICATION
Inconsistent flow Blocked top assembly Remove top assembly and clean
Water is not flowing from tap Water is turned off Turn on water
Blocked flow restrictor Remove restrictor and clean
Continuous flow Top assembly loose or internally
obstructed or damaged
Remove top assembly, clean with water
and re-grease spindle if required
Rate of flow inadequate The flow regulator screw may not be
adjusted correctly
Remove blanking screw and adjust flow
regulating screw as described
Button hard to press The mains pressure may be too
great
Reduce to below 500kPa (70PSI).
Regrease spindle if required
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including
but not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy
for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.