GAPOSA XQ40 User manual

Made in Italy
E
TUBULAR MOTORS WITH ENCODER
ELECTRONIC LIMITS

INDEX
SAFETY
INSTALLATION
ELECTRICAL CONNECTION
SETTING THE LIMITS
SETTING WITH PUSHBUTTON TOOL
ACPRE/ACPRET (optional)
SETTING WITH STANDARD PUSHBUTTON
[only for XQ50]
OPTION 1.
Shutter with mechanical stops or
cassette awnings
OPTION 3.
Shutter with mechanical stops or
cassette awnings
OPTION 2.
Shutter or awnings without stops
OPTION 4.
Shutter or awnings without stops

SAFETY
CAREFULLY FOLLOW THESE INSTRUCTIONS. IT IS VERY
IMPORTANT FOR THE SAFETY OF PERSONS. SAVE THESE
INSTRUCTIONS.
IMPORTANT:
•Checktheshutter/awninginmotionandkeeppersonsfar
fromitwhileinaction.
•Frequentlycheckifanylossofbalance,signsofwearor
damagedwiresareshown.
•Donotuseifanyrepairingormaintenanceisneeded.
•Incaseofinstallationinawningskeepadistanceofat
least0,4mfromit(completelyopen)andwhateverxed
iteminthenearby.
•Thedeviceisnotintendedtobeusedbypeople(including
children)whosephysical,sensoryormentalcapabilities
arereduced,orlackingexperienceorknowledge,unless
theyhavebeengrantedthroughtheintermediaryof
apersonresponsiblefortheirsafety,supervisionor
instructionconcerningtheuseofthedevice.
•Childrenshouldbesupervisedtoensuretheydonotplay
withthedeviceand/orwithxcontroldevices.
•Thecontroldevicesinstalledinaxedmannermustbe
positionedinview.

1/2
To complete installation, the motor must be provided with a couple of
adaptors (corresponding with the tube) and a fixing bracket. For a list of the
available accessories, refer to the catalogue.
WARNING: incorrect installation can cause serious injuries. Follow
the installation instructions. Before you remove all unnecessary
cables and turn off any equipment not required for this operation.
1Fix the adaptors to the motor distinguishing the limits ring from
the drive pulley .
A
B
2Insert the motor into the tube until its end stops against the
limits ring.
E
F
INSTALLATION

2/2
3
The fixing bracket must be fixed inside the box or on the awning
frame so that the roller tube is perfectly horizontal and at a
height not less than 1,8m.
4
[FOR XQ50] Place the motor square pin on the bracket and
the cap at the opposite end of the tube on the fixing plate.
WARNING: Never hit on the head of the motor (D) when you
insert it into the tube.
F
90°
min1,8m
C
D
NOTES
•FortheXQ50,withtorqueupto15Nm,theminimumtubediameteris50x1,5mm;
formotorswithhighertorques,theminimumtubediameteris60x1,5mm.
•FortheXQ60,theminimumtubediameteris63x1,5mm.

WARNING:
•Thescrewsusedtoxthelastslatonthetubemaybetoolongandreachthe
tubularpartofthemotor.Useappropriatescrewsorxingclips.
•Motormovingpartsinstalledunder2,5mfromthegroundmustbeprotected.
•Awrongmotorinstallationcandamagepersonsorobjects.
INSTALLATION

P
4x0.75 mm2
1/2ELECTRICAL CONNECTION
Check that the mains voltage available on the system is as shown
on the label. The motor mains connection should be executed according
to the diagram on the next page, by qualified technicians able to operate in
compliance with the rules.
ATTENTION: The power supply must contemplate a switching device
with an opening distance between contacts of at least 3mm.
The motors connecting cables to the network can only be replaced with
cables of the same type provided by the motor manufacturer.
•Do not connect more than one tubular motor to a single switch.
•Do not set the shutter/awning into motion while you are cleaning or
servicing the device and disconnect the supply.
•The switch controlling the motor must be installed in full view, not higher
than 1,5m and it must be kept far from moving parts.
230 V~ / 50 Hz
Powersupply
Neutral Blue
Ground Yellow/Green
Direction of rotation 1 Brown
Direction of rotation 2 Black
Neutral
Ground
Phase
PPush button

2/2ELECTRICAL CONNECTION
IMPORTANT INFORMATION FOR ELECTRICIANS
•It is possible to connect in parallel electronic motors to a switch in
residential applications where the total power cable length does
not exceed 10 meters. The number of motors paralleled together
is limited to 4-5 according to the switch total amperage capacity.
•Electronic motors cannot be paralleled connected together
when controlled by a Building Management system (BMS).
•Compatibility between electronic motors and BMS must be
approved and tested by manufacturer of BMS.
•For standard motor operation only a standard switch allowing either
UP or DOWN but not both at the same time must be used. Only
mechanically or electrically interlocked switches can be used.
•Motors with electronic limits can be connected in parallel. The
maximum load of the switch must never be exceeded.
•When changing from UP to DOWN or vice versa, the switchover time
must at least be 0.5 seconds and effected through an OFF position.
Only switches with a defined neutral position or one with a built-in
switching delay should be used.
•An “active path” control unit which monitors the current draw is in
conflict with the motor and cannot be used.

IMPORTANT:
•Motors are supplied with pre-set limit switches, in order to
allow two turns in both directions.
•Limit-switches setting procedures shown are valid for right and
left side installation.
•Always set the UP limit switch FIRST
SETTING THE LIMITS
SETTING WITH PUSHBUTTON TOOL
ACPRE/ACPRET (optional)
CHOOSE AN OPTION
SETTING WITH STANDARD PUSHBUTTON
[only for XQ50]
OPTION 1.
Shutter with
mechanical stops or
cassette awnings
OPTION 3.
Shutter with
mechanical stops or
cassette awnings
OPTION 2.
Shutter or awnings
without stops
OPTION 4.
Shutter or awnings
without stops

1/2
1Connect the motor to the
pushbutton ACPRE/ACPRET
ACPRE ACPRET
STOP STOP
2Press Up and Down buttons simul-
taneously until the motor jogs
STOP STOP
15”
3
Press the Up button and release it
only when the motor stops because
the shutter/awning has reached the
Up stops. Up limit switch is set
SETTING WITH
PUSHBUTTON TOOL
ACPRET/ACPRE (option)
OPTION 1.
Shutter with mechanical stops
or cassette awnings

2/2
4
Press the Down button and re-
lease it only when the shutter/
awning has reached the desired
limit switch position
5
Press Up and Down buttons
simultaneously until the motor
jogs. Down limit switch is set
STOP STOP
15”
6Disconnect the setting pushbutton tool ACPRE/ACPRET and
connect the motor to the final standard pushbutton.

1/2
1Connect the motor to the
pushbutton ACPRE/ACPRET
ACPRE ACPRET
STOP STOP
2Press Up and Down buttons simul-
taneously until the motor jogs
STOP STOP
15”
3
Press the Up button and release it
only when the motor stops because
the shutter/awning has reached the
Up stops. Up limit switch is set
OPTION 2.
Shutter or awnings without stops
SETTING WITH
PUSHBUTTON TOOL
ACPRET/ACPRE (option)

2/2
4
Press Up & Down buttons simul-
taneously until the motor jogs. Up
limit switch is set.
STOP STOP
15”
5
Press the Down button and release
it only when the shutter/awning has
reached the desired limit switch posi-
tion.
6
Press Up and Down buttons simulta-
neously until the motor jogs. Down
limit switch is set
STOP STOP
15”
7Disconnect the setting pushbutton tool ACPRE/ACPRET and
connect the motor to the final standard pushbutton

1/2
1
Press the white button on the motor head together with one of
the two pushbuttons until the motor jogs.
15”
2
Press the Up button and release it
only when the motor stops because
the shutter/awning has reached the
Up stops. Up limit switch is set;
OPTION 3.
Shutter with mechanical stops or cassette awnings
SETTING WITH STANDARD
PUSHBUTTON
[only for XQ50]

2/2
3
Press the Down button and release
it only when the shutter/awning has
reached the desired limit switch
position.
4
Press the white button on the motor head together with one of
the two pushbuttons until the motor jogs.
Down limit switch is set;
15”

1/2
1
Press the white button on the motor head together with one of
the two pushbuttons until the motor jogs.
15”
2
Press the Up button and release it
when the shutter/awning has rea-
ched the desired limit switch posi-
tion
OPTION 4.
Shutter or awnings without stops
SETTING WITH STANDARD
PUSHBUTTON
[only for XQ50]

GAPOSA srl - via Ete, 90
63900 Fermo - Italy
T. +39.0734.220701 - [email protected]
2/2
3
Press the white button on the motor head together with one of
the two pushbuttons until the motor jogs. The Up limit switch
is set.
15”
4
Press the Down button and release
it only when the shutter/awning has
reached the desired limit switch
position. Press Up or Down button to
find the exact final position.
5
Press the white button on the motor head together with one of
the two pushbuttons until the motor jogs.
The Down limit switch is set
15”