GARO GLB-SMART Setup guide

GARO GLB-SMART
Quick Start User Guide
GARO Electric Limited
Unit 19/307 Northwest Business Park, Ballycoolin, Dublin D15AV81
Phone: [phone]
[e-mail]
garoelectric.com

1) Viewing your Chargepoint Main Screen
A. Click to set time
B. Double Click GARO logo for
extended information
C. Wallbox Status
D. Dropdown List*:
•Available for charging
•Not available for charging
•Schedule
E. Details of Load Balancing
Garo GLB-SMART features Metering, Wifi/LAN and a WebApp to allow you to optimise
your charging sessions from a cost, energy efficiency and sustainability point of view.
The following guide assumes your GLB-SMART has been connected to your home Router or
Phone as per the installation manual (Steps are repeated at the end of this guide).
GARO GLB-SMART Quick Start User Guide
1

2
Energy Providers can offer reduced tariffs for EV Charging. To set your GLB-SMART to
Charge at specific time periods follow step C below.
2) Scheduling Charging
You can also select periods of
low Charging rate.
During this time period you can
choose a different power output
from the Charger (to reduce costs
at peak times).
From the Charge Current Settings
tab select a Charging rate, time
period and click Add.
A. Available for charging means that the
GLB Wallbox is activated.
B. Not available for charging means that
the GLB Wallbox is deactivated.
C. Schedule means that you can set periods
when the GLB Wallboxes should be activated.
Enter your times for charging and click book.

3
Select “Energy” from the bottom of Home menu. Your current month’s kWh usage will be
displayed.
You can also:
•select any historical month
•export to PDF
•add a unit of electricity cost to work out the monetary cost of charging
3) Viewing Your Energy Analysis

Your Garo GLB-SMART can connect to an external Meter (Garo GNM100-RS485) to
manage the amount of power used in your home and safely distribute it between the
Charger and appliances. The appliances in the home are given priority. Should their
consumption climb to a threshold which could exceed the main fuse if full EV Charging
is present, the GLB-SMART will reduce its charging rate until the appliances power has
reduced. You can view the status of the Load Balancing System by selecting the Load-
Balancing Meter as shown below.
4) Load Balancing From External Meter
4

5
Connecting GLB-SMART to your Phone or Network
General information
GLB Wallbox Conditions
•Installed wifi module
•Electrified wallbox
Note: Please wait up to 3 minutes before the wifi module is ready after power on.
The wifi module is set to “Accesspoint” as default and in this mode you should search
after the wallbox SSID in your device.
SSID and password are written on the label inside the black front on the GLB.
You can connect the wifi module to a local network via wifi or LAN (ethernet port).
In this mode, your device need to be connected to same network to have access to the
web interface.
1. Search for the GLB Wallbox SSID and press connect. Type in the password located
on the wallbox label. The label is located inside the black front on the GLB.
2. Open a web browers. If the web interface does not appear, type in “172.24.1” in
the address field.
Connect device to GLB Wallbox access point

6
A. Dropdown List:
•Local accesspoint (default)
•Connect to router
•Wifi diabled (only visible for
LAN connected wallbox)
B. Accesspoint password - more information
shows wifi modules MAC address.
C. Field for own password.
D. Enable internet hotspot (only visible for
LAN connected wallbox)
Connecting GLB-SMART to your Phone or Network
Connect GLB Wallbox to local wifi network
General information
Make sure that your local network uses a secure firewall to
avoid unwanted access to the wallbox from the internet.
Only 2.4GHz wifi network are supported.
5GHz wifi network is not supported.
Firewall/router must handle outgoing request to:
*8.8.8.8 via ICMP(ping)
*85.11.39.104 (www.webel-online.se) via ICMP(ping),
TCP port 80 and TCP port 443
Make sure your router/firewall does not block this traffic.
WPA/WPA2 encryption is supported. WPA2 Enterprise is
not supported.
Local wifi network must have a password. The wallbox can
not connect to an open wifi network that does not request
a password.
A. Connect wallbox to local wifi network. Choose ‘Connected to router’ in the dropdown list.
B. Click scan for wifi networks. Click wanted network, type in password and click save.
C. Save
Enter http://chargebox.webel.se/ to access the Garo WebApp