Genie WAHD841 User manual

Quick Start Guide
Please read these instructions carefully before operating the unit
and keep for further reference.
4 & 8 Channel 5-in-1 8MP
Hybrid DVR’s with 1HDD Bay
WAHD841 | WAHD881

ii
Intro Section
Please read this instruction carefully before operating the product and keep it for further
reference. All examples and pictures used here are for reference only.
The contents of this manual are subject to change without notice.
CAUTION:
• Please check the device and the accessories after getting the device. If there are any
damages, shortages or defects, please contact your dealer immediately.

Contents
iii
1.0 Introduction..........................................................................................................4
1.1 Product Features...........................................................................................4
1.2 Product Dimensions.....................................................................................4
1.3 Specification.................................................................................................5
2.0 HDD Installation...................................................................................................6
3.0 Rear Panel Instruction..........................................................................................7
4.0 Start Up and Shut Down......................................................................................8
5.0 Login ....................................................................................................................9
6.0 Configurations and Connections ........................................................................10
6.1 Ananlogue Camera Connection...................................................................10
6.2 Network Configuration & Adding IP Camera..............................................10
7.0 UPnP .....................................................................................................................12
8.0 NAT.......................................................................................................................13
9.0 Manual Recording and Playback .........................................................................14
9.1 Manual Recording.........................................................................................14
9.2 Playback.......................................................................................................14

4
The Genie WAHD841 and WAHD881 are 4 and 8 channel 8MP, 5MP, 4MP, 3MP, 1080P,
720P and WD1 high definition DVR’s with the ability to connect analogue and IP cameras
simultaneously and adopts the standard H.265 high profile compression format.
The WAHD841 supports 4 channel video input, 1 channel audio input and 4 channel
simultaneous playback whilst the WAHD881 supports 8 channel video input, 1 channel audio
input and 8 channel simultaneous playback.
1.1 Product Features
• 4 and 8 channel TVI / AHD / CVI 8MP, 5MP, 4MP, 3MP, 1080p, 720p and WD1 video input
• 4 and 8 channel DVR support. 2 and 8 channel 8MP, 5MP, 4MP, 3MP, 1080p, 720p and
WD1 IP input by default
• Adopt standard H.265 high profile compression format to get high-quality video at
much lower bit rate
• Intuitive and user-friendly Graphics User Interface (GUI window style operation by
mouse).
• Search: Time Slice, Time, Event, Tag and Smart Search
• Simultaneous multi-user online
• Multi-mode recording: Manual / Timer / Motion / Smart Event Playback : 4 and 8
channel simultaneous playback
• Express and flexible backup via USB and Network
• Pentaplex: Preview, Record, Playback, Backup and Remote Access
• DHCP, DDNS, PPPoE network protocol
• Remote control via IE or CMS : Preview, Playback, Backup, PTZ and Configuration
• Dual stream technology for local storage with high definition, remote network
transmission and remote surveillance with mobile device
• HDMI 4K output, true high resolution display
• Authorisation management, log review and device status review
• Support PTZ preset and auto cruise, up to 255 presets and 8 cruises
• Support NAT function and QR Code scanning by mobile phones
• Powerful mobile surveillance by smart phones with iOS and Android OS
1.2 Product Dimensions
1.0 Introduction
255mm
WAHD841 WAHD881
222mm 234mm
42mm

Quick Start Guide 4 & 8 Channel 5-in-1 8MP Hybrid DVR’s with 1HDD Bay
5
1.3 Specification
Model WAHD841 WAHD881
System OS Embedded Linux
Video
Analogue Video Input BNC x4 BNC x8
BNC interface (1.0Vp-p, 75)
IP Video Input 2CH (Up to 6CH) 8CH (Up to16CH)
Up to 8MP @ 30fps
Total Input 6CH 16CH
Output
HDMI x1 : 3840×2160 / 1920×1080 / 1280×1024 / 1024×768
VGA x1 : 1920×1080 / 1280×1024 / 1024×768
BNC x1 : CVBS (Used as the main or spotoutput)
Compression H.264 / H.265
Audio
Input RCA x1
Output RCA x1 (Linear, 600)
Two-Way Audio Take up channel one audio input
Compression G.711(U/A)
Record
Resolution 4K / 4K Lite / 5MP / 5MP Lite / 4MP / 4MP Lite / 3MP / 1080p / 720p / WD1 / D1
Frame Rate
Analogue Channel: 4K @ 6/7fps (PAL/NTSC) (4 CH DVR: only CH 1 supports, 8CH DVR:
all channels support) 4K Lite @ 12fps/15fps (PAL / NTSC) 5MP @ 12fps (PAL / NTSC)
5MP Lite @ 20fps (PAL / NTSC) 4MP / 3MP @ 12fps (PAL) / 15fps (NTSC)
4MP Lite / 1080p / 720p / WD1 /D1 @ 25fps (PAL) / 30fps (NTSC)
IP Channel: 25fps (PAL) / 30fps (NTSC)
Bit Rate 32Kbps ~ 4Mbps 32Kbps ~ 5Mbps
Mode Manual, Timer, Motion, Smart Event
Mobile Device OS iOS, Android
Storage HDD SATA x1, Up to 6TB per HDD SATA x1, Up to 8TB per HDD
Playback
Playback 4CH 8CH
Search Time Slice / Time / Event / Tag Search
Smart Search Highlight colours to display the camera record in a certain period of time, different
colours refer to different record events
Function Play, Pause, FF, FB, Digital Zoom, etc.
Alarm
Mode Manual, Motion, Exception, Smart Event
Input No
Output No
Network
Interface RJ45 100Mbps x 1
Protocol TCP / IP, PPPoE, DHCP, DNS, DDNS, UPnP, HTTP, HTTPs, NTP, SMTP
Incoming Bandwidth 16Mbps (Max. 40Mbps) 32Mbps (Max. 64Mbps)
Outgoing Bandwidth 40Mbps 80Mbps
Remote
Monitoring
Immix Compatible with Immix via RTSP only (2-way audio not supported)
Sentinel Yes, Firmware 1.1.0 or later
Backup Local Backup USB stick, USB mobile HDD
Network Backup Yes
Port
RS485 RS485 x1, Connect to PTZ or keyboard
USB USB 2.0 x2
Remote Controller Optional
Others
Power Supply DC12V / 1.5A DC12V /2A
Consumption ≤ 10W (Without HDD) ≤ 15W (Without HDD)
Working Environment -10~50°C, 10%~90% (Humidity)
Dimensions 255 × 222 × 42 mm 255 × 234 × 42 mm

6
This series of the product supports 1 SATA hard drive. Please make sure that the device is
powered off before the installation. The pictures of the installation are for reference only.
1. Loosen the screws to open the cover.
2. Place the HDD onto the bottom of the machine.
3. Turn over the machine and secure the HDD with the screws.
4. Connect the power and data cables.
5. Install back the cover and secure it with the screws.
Note: Please check the inside structure of the device and make sure that the cables are
connected well before installing the cover back. Please format the HDD before using.
2.0 HDD Installation

7
The interfaces of the rear panel are for reference only.
Rear panel for WAHD841
Rear Panel for WAHD881
3.0 Rear Panel Instruction
Name Description
VIDEO IN Video input
VGA Connect to monitor
CVBS CVBS output
HDMI HDMI connector; connect to monitor
LAN Network connector
USB Connect to USB storage devices or USB mouses
AUDIO IN Audio input
AUDIO OUT Audio output
RS485 Connect to keyboard or speed dome. A is TX+,B
is TX
DC12V Power input
Internet

8
Startup
1. Connect the monitor and the power.
2. The device will boot and the power indicator will display blue.
3. A wizard window will pop up.
Shutdown
Click “Start” and then select “Shutdown” icon. This will bring up a shutdown window. The
device will shut down by clicking “OK” button. Then disconnect the power.
4.0 Start Up and Shut Down

9
The default username is admin and the default password is 123456. You must configure the
wizard if you start the DVR for the first time and you may change the password when you
configure the wizard for the first time. You can skip the settings wizard next time.
Click “Start” and select “Login”. This will take you to see a login box. Enter the default
username and password you set. Then you will see the live image.
5.0 Login

10
6.1 Ananlogue Camera Connection
First connect the camera to the DVR.
Then go to Start → Settings → Camera→ Manage Camera → Camera Signal to checkmark the
video mode. Theactual signals input shall correspond to the video mode. Please refer to
the User Manual for details.
6.2 Network Configuration & Adding IP Camera
After you finish adding IP cameras, you can see the live images through the monitor of the
DVR. The following will mainly introduce how to add the IP cameras via LAN/WAN.
LAN
1. Set the network of the DVR. Go to Start → Settings → Network → TCP/IP. Enter IP
address, subnet mask, gateway, etc. If using DHCP, please enable DHCP in both the
DVR and the router.
2. Go to Start → Settings → Network → Port. Enter HTTP port (the default value is 80),
server port (the default port is 6036).
3. Click “Apply” to save the settings.
4. Go to Start → Settings → Camera → Add Camera. The DVR will automatically refresh the
cameras searched. The IPC which supports the Onvif protocol may be added manually.
If the IPC searched is not in the same local network as the DVR, you should select the
device and click to modify the IP address.
6.0 Configurations and Connections