Genie DPL Super Series User manual

Operator’s Manual First Edition
Fifth Printing
Part No. 38132
with Maintenance Information

Genie DPL Super Series Part No. 38132
Operator’s Manual First Edition • Fifth Printing
Important
Read, understand and obey these safety rules and
operating instructions before operating this machine.
Only trained and authorized personnel shall be
permitted to operate this machine. This manual should
be considered a permanent part of your machine and
should remain with the machine at all times. If you have
any questions, call Genie Industries.
Contents
Page
Safety Rules .............................................................. 1
Controls ..................................................................... 7
Legend ....................................................................... 8
Pre-operationInspection ............................................ 9
Maintenance ............................................................. 11
Function Tests .......................................................... 14
WorkplaceInspection ................................................ 17
OperatingInstructions ............................................... 18
Battery and Charger Instructions ............................... 20
TransportInstructions ............................................... 21
Decals ...................................................................... 22
Specifications ........................................................... 24
Contact us:
Internet:http://www.genieindustries.com
e-mail:[email protected]
Copyright © 1996 by Genie Industries
First Edition: Fifth Printing, April 2002
"Genie" and "DPL" are registered trademarks
of Genie Industries in the USA and many other
countries. "Super Series" is a trademark of
Genie Industries.
This machine complies with
ANSI/SIA 92.3-1990.
Printed on recycled paper
Printed in U.S.A.

Part No.38132 Genie DPL Super Series 1
Operator’s ManualFirst Edition • Fifth Printing
Safety Rules
Danger
Failure to obey the instructions and
safety rules in this manual will
cause death or serious injury.
Do Not Operate Unless:
You learn and practice the principles of safe
machine operation contained in this operator's
manual.
1 Avoid hazardous situations.
Know and understand the safety rules
before going on to the next section.
2 Always perform a pre-operation inspection.
3 Always perform the function tests prior to use.
4 Inspect the workplace.
5 Only use the machine as it was intended.
You read, understand and obey:
- manufacturer’s instructions and
safety rules—operator’s manual and
machine decals
- employer’s safety rules and worksite
regulations
- applicablegovernmentalregulations
The first time this machine is set up for use, a
breather cap is installed. See Pre-operation
Inspection section for breather cap instructions.

2 Genie DPL Super Series Part No.38132
Operator’s Manual First Edition • Fifth Printing
Tip-over Hazards
Do not raise the platform
unless the base is level,
all four outriggers are
properly set up and the
leveling jacks firmly
contact the ground.
Do not move the machine
while the platform is
raised.
Do not adjust or remove the outriggers while the
platform is occupied or raised.
Do not place or attach overhanging loads to any
part of this machine.
Do not raise the platform
unless the machine is
level. Do not set the
machine up on a surface
where it cannot be leveled
using only the leveling
jacks. Do not use chocks,
blocks or shims of any
kind to level the machine.
Do not place ladders or scaffolds in the platform or
against any part of this machine.
Do not push off or pull toward any object outside
the platform.
Do not use the machine to lift material or
equipment. The machine is intended to lift
personnel and tools to an aerial work site.
Do not use the machine on a moving or mobile
surface or vehicle.
Do not operate the machine in strong or gusty
winds. Do not increase the surface area of the
platform or the load. Increasing the area exposed to
the wind will decrease machine stability.
Do not exceed the rated platform load capacity.
Maximum capacity - DPL-25S
ANSI 750 lbs 340 kg
CSA 600 lbs 272 kg
Maximum occupants - ANSI and CSA 2
CE 750 lbs 340 kg
Maximum occupants - CE
Outdoor use 1
Indoor use only 2
Maximum capacity - DPL-30S
ANSI 750 lbs 340 kg
CSA 600 lbs 272 kg
Maximum occupants - ANSI and CSA 2
CE 750 lbs 340 kg
Maximum occupants - CE
Outdoor use 1
Indoor use only 2
SAFETY RULES

Part No.38132 Genie DPL Super Series 3
Operator’s ManualFirst Edition • Fifth Printing
Maximum capacity - DPL-35S
ANSI 600 lbs 272 kg
CSA 500 lbs 227 kg
Maximum occupants - ANSI and CSA 2
CE 600 lbs 272 kg
Maximum occupants - CE
Outdoor use 1
Indoor use only 2
Do not operate the machine near drop-offs, holes,
bumps, debris, unstable or slippery surfaces or
other possible hazardous conditions.
Do not alter or disable machine components that in
any way affect safety and stability.
Do not replace items critical to stability with items
of different weight or specification. Use only Genie
authorizedreplacementparts.
When moving the machine with a forklift or other
transport vehicle, the platform should be fully
lowered, the guard rails should be down, the
machine should be turned off and no personnel
shall remain in the platform.
SAFETY RULES
Fall Hazards
Do not sit, stand or climb
on the platform guard rails.
Maintain a firm footing on
the platform floor at all
times.
Do not enter or raise the
platform unless the
platform side guard rails
are locked upright and the
platform end guard rail and
the platform entry gate are
closed and latched.
Do not exit the platform while raised. If a power
failure occurs, have ground personnel activate the
manual lowering valve.
Keep the platform floor clear of debris.

4 Genie DPL Super Series Part No.38132
Operator’s Manual First Edition • Fifth Printing
SAFETY RULES
Electrocution Hazards
This machine is not
electrically insulated and
will not provide protection
from contact with or
proximity to electrical
current.
Keep away from the
machine if it contacts
energized power lines or
becomes electrically charged. Personnel on the
ground or in the platform must not touch or operate
the machine until the energized power lines are
shut off.
Maintain safe distances from electrical power lines
and apparatus in accordance with applicable
governmental regulations and the following chart.
Voltage Minimum Safe
Approach Distance
Phase to Phase Feet Meters
0 to 300V Avoid Contact
300V to 50KV 10 3.05
50KV to 200KV 15 4.60
200KV to 350KV 20 6.10
350KV to 500KV 25 7.62
500KV to 750KV 35 10.67
750KV to 1000KV 45 13.72
Allow for platform movement, electrical line sway
or sag and movement due to strong or gusty winds.
Do not use the machine as a ground for welding.
Do not operate an AC powered machine or a DC
battery charger unless using a 3-wire grounded
extension cord connected to a grounded AC circuit.
Do not alter or disable the 3-wire grounded plugs.
Collision Hazards
Check the work area for overhead obstructions or
other possible hazards.
Be aware of crushing hazard when grasping the
platform side guard rails.
Do not lower the platform unless the area below is
clear of personnel and obstructions.
Be careful when transporting on an incline.
Stay clear of descending platform.
Component Damage Hazards
Do not operate the machine unless a breather cap
has been installed in the hydraulic reservoir. See
Pre-operation Inspection section for breather cap
instructions.
Do not use the machine as an electrical ground for
welding.
DC models: Do not operate the machine with a
weak or overly discharged battery.

Part No.38132 Genie DPL Super Series 5
Operator’s ManualFirst Edition • Fifth Printing
Decal Legend
Genie product decals use symbols, color coding
and signal words to identify the following:
Safety alert symbol—used to alert
personnel to potential personal
injury hazards. Obey all safety
messages that follow this symbol
to avoid possible injury or death.
Red—used to indicate the
presence of an imminently
hazardous situation which, if not
avoided, will result in death or
serious injury.
Orange—used to indicate the
presence of a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
Yellow with safety alert symbol—
used to indicate the presence of a
potentially hazardous situation
which, if not avoided, may cause
minor or moderate injury.
Yellow without safety alert
symbol—used to indicate the
presence of a potentially
hazardous situation which, if not
avoided, may result in property
damage.
Green—usedtoindicate operation
ormaintenanceinformation.
SAFETY RULES
Improper Use Hazard
Do not leave the machine unattended unless the
key is removed to secure from unauthorized use.
Damaged Machine Hazards
Do not use a damaged or malfunctioning machine.
Conduct a thorough pre-operation inspection of the
machine and test all functions before each
work shift. Immediately tag and remove from
service a damaged or malfunctioning machine.
Be sure all maintenance has been performed
as specified in this manual and the Genie DPL
Service Manual .
Be sure all decals are in place and legible.
Be sure the operator’s, safety and responsibilities
manuals are complete, legible and in the storage
container located in the platform.
Bodily Injury Hazard
Do not operate the machine with a hydraulic oil or
air leak. An air leak or hydraulic leak can penetrate
and/or burn skin.

6 Genie DPL Super Series Part No.38132
Operator’s Manual First Edition •Fifth Printing
Battery and Charger Safety
- DC Models
Burn Hazards
Batteries contain acid. Always wear protective
clothing and eyewear when working with batteries.
Avoid spilling or contacting battery acid. Neutralize
battery acid spills with baking soda and water.
Explosion Hazards
Batteries emit explosive gas.
Keep sparks, flames and
lighted tobacco away from
the battery.
Charge the battery in a
well-ventilatedarea.
Do not disconnect the charger DC output wires from
the battery when the charger is on.
The sliding door on the base cover must remain
open during the entire charging cycle.
Electrocution Hazards
Connect the charger to a
grounded AC circuit only.
Do not expose the battery or
the charger to water or rain.
Before each use, inspect for
damage.Replacedamaged
items before operating.
Lifting Hazard
The battery weighs 105 lbs / 48 kg. Use the
appropriate number of people and proper lifting
techniques when lifting the battery.
SAFETY RULES

Part No.38132 Genie DPL Super Series 7
Operator’s ManualFirst Edition •Fifth Printing
Controls
Ground Controls
- AC & DC Models
Platform Controls
1
9
10
3 4
7 6 5
1 2
1 Red Emergency Stop button
2 Key switch
3 Outrigger interlock display lights (four)
4 Low battery indicator light for auxiliary
lowering
5 DC models: Low battery indicator light
6 Powerlight
7 Auxiliary platform lowering button
8 Airpressure gauge
9 Control activate button
10 Up/Downswitch
Ground Controls
- Air Models
38 12

8 Genie DPL Super Series Part No.38132
Operator’s Manual First Edition •Fifth Printing
1 Platform end guard rail
2 Platform side guard rail
3 Manualstoragecontainer
4 Platform controls
5 AC outlet
6 Platform entry gate
7 Platform end gate latch
8 Platform
9 Interlock display
10 AC models: Circuit breaker
11 Platform entry ladder
12 AC models: Power supply for
machine
DC models: AC power to
platform
13 Platform entry ladder lock pin
14 Outrigger with leveling jack
15 Forklift pocket
16 Bubble level
17 Sequencingcable
18 Transporttie-down
19 Manualloweringlever
20 Batterycharger plug-in
21 Base
22 Caster with swivel lock
23 Base cover
24 Mast
25 Steerhandle
26 Platform guard rail locking
handle
27 Guard rail lifting arm
28 Air line lubricator adjustment
knob
29 Air supply for machine
30 Air line lubricator
Legend
Air Models

Part No.38132 Genie DPL Super Series 9
Operator’s ManualFirst Edition •Fifth Printing
Pre-operation Inspection
Do Not Operate Unless:
You learn and practice the principles of safe
machine operation contained in this operator’s
manual.
1 Avoid hazardous situations.
2 Always perform a pre-operation
inspection.
Know and understand the pre-operation
inspection before going on to the next
section.
3 Always perform the function tests prior to use.
4 Inspect the workplace.
5 Only use the machine as it was intended.
Breather Cap - AC & DC
Models
Component damage will occur if the machine
is operated without a breather cap.
The first time this machine is
set up for use, the pipe plug in
the hydraulic reservoir, under the
battery cover, must be removed
and permanently replaced with a
breathercap.
A breather cap is supplied and
can be found in an envelope
taped to the mast.
Fundamentals
It is the responsibility of the operator to perform a
Pre-operationInspectionand routine maintenance.
The Pre-operation Inspection is a visual inspection
performed by the operator prior to each work shift.
The inspection is designed to discover if anything
is apparently wrong with a machine before the
operator performs the function tests.
The Pre-operation inspection also serves to
determine if routine maintenance procedures are
required. Only routine maintenance items specified
in this manual may be performed by the operator.
Refer to the list on the next page and check each
of the items and locations for modifications,
damage or loose or missing parts.
A damaged or modified machine must never be
used. If damage or any variation from factory
delivered condition is discovered, the machine
must be tagged and removed from service.
Repairs to the machine may only be made by a
qualified service technician, according to the
manufacturer's specifications. After repairs are
completed, the operator must perform a
pre-operation inspection again before going on to
the function tests.
Scheduled maintenance inspections shall be
performed by qualified service technicians,
according to the manufacturer's specifications and
the requirements listed in the responsibilities
manual.

10 Genie DPL Super Series Part No.38132
Operator’s Manual First Edition •Fifth Printing
Pre-operation Inspection
oBe sure that the operator’s, safety and
responsibilities manuals are complete, legible
and in the storage container located in the
platform.
oBe sure that all decals are legible and in place.
See Decals section.
oCheck for battery fluid leaks and proper fluid
level. Add distilled water if needed. See
Maintenancesection.
oAC & DC models: Check for hydraulic oil leaks
and proper oil level. Add oil if needed. See
Maintenancesection.
oAir models: Check the oil level of the air line
lubricator. Add oil as needed. See Maintenance
section.
oAir models: Check the oil lubricator Canister drip
rate. Adjust as needed. See Maintenance
section.
oAir models: Check the air filter/regulator
canister. Drain water as needed. See
Maintenancesection.
Check the following components or areas for
damage and improperly installed, loose or missing
parts:
oElectrical components and wiring
oCoil cord (if equipped)
oAC & DC models: Hydraulic power unit,
hoses, fittings and cylinders
oAir models: Air power unit, air lines, hoses,
fittings and cylinders
oManualloweringlever
oPlatform end guard rail, platform side guard
rails and platform entry gate
PRE-OPERATIONINSPECTION
oGuard rail lock handles
oSequencing cables and pulleys
oLifting chains and idler wheels
oNuts, bolts and other fasteners
oMast and mast braces
oBreathercap
oOutriggers, leveling jacks and footpads
oGuard rail lift arm
oPlatform entry ladder
Check entire machine for:
oDents or damage
oCorrosionoroxidation
oCrack in welds or structural components
oInspect and clean battery terminals and all
battery cable connections.
oBe sure that all structural and other critical
components are present and all associated
fasteners and pins are in place and properly
tightened.

Part No.38132 Genie DPL Super Series 11
Operator’s ManualFirst Edition •Fifth Printing
Maintenance
Observe and Obey:
Only routine maintenance items specified in this
manual shall be performed by the operator.
Scheduled maintenance inspections shall be
completed by qualified service technicians,
according to the manufacturer's specifications
and the requirements specified in the
responsibilitiesmanual.
Maintenance Symbols Legend
The following symbols have been
used in this manual to help
communicate the intent of the
instructions. When one or more of
the symbols appear at the
beginning of a maintenance
procedure, it conveys the meaning
below.
Indicates that tools will be required to
performthis procedure.
Indicates that new parts will be required to
performthis procedure.
Check the Battery - DC Models
Proper battery condition is essential to good
machineperformance and safe operation. Improper
fluid levels or damaged cables and connections can
result in engine component damage and hazardous
conditions.
Electrocution hazard. Contact with
hot or live circuits could result in
death or serious injury. Remove all
rings, watches and other jewelry.
Bodily injury hazard. Batteries
contain acid. Avoid spilling or
contacting battery acid. Neutralize
battery acid spills with baking soda
andwater.
Perform this test after fully
charging the batteries.
1 Put on protective clothing and eye wear.
2 Remove the battery vent caps.
3 Check the battery acid level. If needed,
replenish with distilled water to the bottom of the
battery fill tube. Do not overfill.
4 Install the vent caps.

12 Genie DPL Super Series Part No.38132
Operator’s Manual First Edition •Fifth Printing
MAINTENANCE
Check the Hydraulic Oil Level -
AC and DC Models
Maintaining the hydraulic oil at the proper level is
essential to machine operation. Improper hydraulic
oil levels can damage hydraulic components. Daily
checks allow the inspector to identify changes in oil
level that might indicate the presence of hydraulic
system problems.
1 Be sure the platform is fully lowered.
2 Check the sight gauge on the side of the
hydraulicreservoir.
Result: The hydraulic oil level should be visible
in the middle of the sight gauge. Do not overfill.
Hydraulic oil specifications
Hydraulic oil type Dexron equivalent
Check the Air Line Lubricator
Oil Level - Air Models
Maintaining the proper oil level in the lubricator
canister is essential to safe operation and good
machine performance. Failure to keep the lubricator
canister at the proper oil level could result in unsafe
operating conditions and possible component
damage.
1 Be sure the platform is fully lowered.
2 Inspect the lubricator canister for the proper oil
level.
Result: The oil level must be within 1/2inch /
12.7 mm from the top of the lubricator canister.
3 To add oil, remove the oil lubricator canister
from the lubricator base and fill with oil. Install
the canister back onto the lubricator base.
Oil Specifications
Oil Type 10W automotive engine oil

Part No.38132 Genie DPL Super Series 13
Operator’s ManualFirst Edition •Fifth Printing
MAINTENANCE
Check the Oil Lubricator
Canister Drip Rate - Air Models
Maintaining the proper oil drip rate into the lubricator
canister is essential to safe operation and good
machine performance. Failure to maintain the
proper drip rate could result in machine component
damage.
1 While raising the platform, visually inspect the
oil lubricator sight gauge.
Result: There should be a maximum of 1 to 2
drops of oil visible in the sight gauge.
2 To adjust the drip rate, turn the oil flow control
valve clockwise to decrease the flow or
counterclockwise to increase the flow.
3 Repeat this procedure until the proper oil drip
rate is achieved.
Check the Air Filter/Regulator
Canister - Air Models
It is essential to drain the air filter/regulator canister
of water to ensure good air motor performance and
service life. A water-filled canister could cause the
air motor to perform poorly and continued use could
causecomponent damage.
1 Check the air filter/regulator canister for any
wateraccumulation.
2 If water is visible, loosen the drain plug at the
bottom of the canister and allow the water to
drain out.
3 Tighten the drain plug.
Scheduled Maintenance
Maintenanceperformedquarterly, annually and
every two years must be completed by a person
trained and qualified to perform maintenance on this
machine according to the procedures found in the
service manual for this machine.
Machines that have been out of service for more
than three months must receive the quarterly
inspection before they are put back into service.

14 Genie DPL Super Series Part No.38132
Operator’s Manual First Edition •Fifth Printing
Fundamentals
The Function Tests are designed to discover any
malfunctions before the machine is put into service.
The operator must follow the step-by-step
instructions to test all machine functions.
A malfunctioning machine must never be used. If
malfunctions are discovered, the machine must be
tagged and removed from service. Repairs to the
machine may only be made by a qualified service
technician, according to the manufacturers
specifications.
After repairs are completed, the operator must
perform a pre-operation inspection and function
tests before putting the machine into service.
Do Not Operate Unless:
You learn and practice the principles of safe
machine operation contained in this operator’s
manual.
1 Avoid hazardous situations.
2 Always perform a pre-operation inspection.
3 Always perform the function tests prior
to use.
Know and understand the function tests
before going on to the next section.
4 Inspect the workplace.
5 Only use the machine as it was intended.
Function Tests
1 Position the machine directly below the desired
workarea.
2 Connect to the appropriate power source:
DC models: Connect the battery pack.
AC models: Connect to a grounded 15A AC
power supply. Use a 12 gauge / 3.3 mm2
3-wire grounded extension cord no longer than
50 feet / 13 m.
Air models: Connect the airline.
3 Insert the key and turn to the on position OR
turn to platform control.
4 Pull out the red Emergency Stop button at the
groundcontrols.
Result: AC & DC Models: The power light should
come on.
Air models: The pressure gauge should read
80-110 psi / 5.5-7.8 bar.
FunctionTests

Part No.38132 Genie DPL Super Series 15
Operator’s ManualFirst Edition •Fifth Printing
FUNCTIONTESTS
5 Install each outrigger and adjust the leveling
jacks to level the machine. Level the machine
using only the outriggers. Do not use chocks,
blocks or shims to level the machine.
6 Check the interlock display. Be sure that all four
interlock display lights are on.
7 Use the bubble level and adjust
the leveling jacks until the
machine base is level.
8 Rotate the platform guard
rail locking handle and
rotate the platform side
guard rail to the upright
position. Be sure the side
guard rail locks in place.
Repeat for the other side.
9 Pull the ladder lock pins and rotate the ladder
down. Be sure the ladder locks in place.
10 Climb the ladder to enter the platform. Close and
latch the platform entry gate and the platform
end guard rail.
Test Emergency Stop
11 Twist to release the red Emergency Stop button
at the platform controls.
12 Push in the red Emergency Stop button at the
ground controls to the off position.
13 Push in the control
activate button and
rotate the up/down
switch in the direction
of intended travel.
Result: The up/down
function should not
operate.
14 Push in the red Emergency Stop button at the
platform controls to the off position.
15 Pull out the red Emergency Stop button at the
ground controls to the on position.
16 Push in the control activate button and rotate
the up/down switch in the direction of intended
travel.
Result: The up/down function should not
operate.

16 Genie DPL Super Series Part No.38132
Operator’s Manual First Edition •Fifth Printing
FUNCTIONTESTS
Test Outrigger Interlock
17 Twist to release the red Emergency Stop button
at the platform controls.
Result: The up/down function should operate.
18 Unscrew one leveling jack until the
corresponding interlock display light turns off.
Result: The up/down function should not
operate.
19 Return the leveling jack to the previous setting
and check the bubble level.
20 Repeat the procedure for each outrigger.
Test Auxiliary Platform Lowering
- AC & DC Models
21 Raise the platform slightly.
22 Disconnect the power source from the machine.
23 Turn the key switch to ground control (if
equipped).
24 Push in the auxiliary platform lowering button at
the ground controls.
Result: The platform should lower.
25 Connect the power source to the machine.
26 Turn the key switch to platform control (if
equipped).
27 Raise the platform slightly.
28 Disconnect the power source from the machine.
29 Push in the control activate button and rotate
the up/down switch in the down direction.
Result: The platform should lower.
30 Connect the power source to the machine.
Test Manual Lowering
31 Raise the platform slightly.
32 Activate the manual lowering lever.
Result: The platform should lower.

Part No.38132 Genie DPL Super Series 17
Operator’s ManualFirst Edition •Fifth Printing
Do Not Operate Unless:
You learn and practice the principles of safe
machine operation contained in this operator’s
manual.
1 Avoid hazardous situations.
2 Alwaysperforma pre-operation
inspection.
3 Always perform function tests prior to use.
4 Inspecttheworkplace.
Knowandunderstandtheworkplace
inspection before going on to the next
section.
5 Only use the machine as it was intended.
Fundamentals
The Workplace Inspection helps the operator
determine if the workplace is suitable for safe
machine operation. It should be performed by the
operator prior to moving the machine to the
workplace.
It is the operator’s responsibility to read and
remember the workplace hazards, then watch for
and avoid them while moving, setting up and
operatingthe machine.
Workplace Inspection
Workplace Inspection
Be aware of and avoid the following hazardous
situations:
·drop-offs or holes
·bumps, floor obstructions or debris
·overhead obstructions and high voltage
conductors
·hazardouslocations
·inadequate surface support to withstand all load
forces imposed by the machine
·wind and weather conditions
·the presence of unauthorized personnel
·other possible unsafe conditions

18 Genie DPL Super Series Part No.38132
Operator’s Manual First Edition •Fifth Printing
OperatingInstructions
Do Not Operate Unless:
You learn and practice the principles of safe
machine operation contained in this operator’s
manual.
1 Avoid hazardous situations.
2 Alwaysperforma pre-operation
inspection.
3 Always perform function tests prior to use.
4 Inspect the workplace.
5 Only use the machine as it was
intended.
Fundamentals
Using the machine for anything other than lifting
personnel and material to an aerial work site is
unsafe.
If more than one operator is expected to use a
machine at different times in the same work shift,
each operator is expected to follow all safety rules
and instructions in the operator’s manual. That
means every new operator should perform a pre-
operation inspection, function tests and a
workplace inspection before using the machine.
Setup
1 Position the machine directly below the desired
workarea.
2 Connect to an appropriate power source:
DC models: Connect the battery pack.
AC models: Connect to a grounded 15A AC
power supply. Use a 12 gauge / 3.3 mm²3-wire
grounded extension cord no longer than
50 feet / 13 m.
Air models: Connect the air line.
3 Insert the key and turn to the on position OR
turn to platform control.
4 Pull out the red Emergency Stop button at the
ground controls. Be sure the power light is on or
the air pressure gauge reads 80-110 psi /
5.5-7.8bar.
5 Install the outriggers and adjust the leveling
jacks to level the machine. Check the bubble
level to be sure the machine is level.
6 Check the interlock display. Be sure that all four
interlock display lights are on.
7 Pull down on the
platform guard rail
locking handle and
rotate the platform side
guard rail to the upright
position. Be sure the
side guard rail locks in
place. Repeat for the
other side.
8 Pull the ladder lock pins and rotate the ladder
down. Be sure the ladder locks in place.
9 Climb the ladder to enter the platform. Close and
latch the platform entry gate and the platform
end guard rail.