Genie PWIP2BV User manual

Quick Start Guide
Please read these instructions carefully before operating the unit
and keep for further reference.
2MP H.265 IP IR Bullet Camera
with 2.8-12mm Varifocal Lens
PWIP2BV

ii
Intro Section
Please read this instruction carefully before operating the product and keep it for further
reference. All examples and pictures used here are for reference only.
The contents of this manual are subject to change without notice.
CAUTION:
• If the product does not work properly, please contact your dealer or the nearest service
centre. Never attempt to disassemble the camera yourself. We shall not be responsible
for any problems caused by unauthorised repair or maintenance.
• Do not allow water or liquid into the camera while in use.
• When using the product, you must be in strict compliance with the electrical safety
regulations of the nation and region.
• When the product is mounted on wall or ceiling, the device needs to be firmly fixed.
• Make sure the power supply voltage is correct before using the camera.
• Do not drop the camera or subject it to any physical shock.
• If cleaning, please use a clean soft cloth with a little neutral detergent to wipe it gently.
• Do not aim the camera at the sun or in any area where there is bright lighting.
• The device may be burned out by a laser beam, so when any laser equipment is in use,
make sure that the surface of the device will not be exposed to the laser beam.
• Do not place the camera in extremely hot, cold , dusty or damp locations, and do not
expose it to high electromagnetic radiation.
• To avoid heat accumulation, good ventilation is required for operating environment.

Contents
iii
1.0 Introduction..........................................................................................................4
1.1 Product Features...........................................................................................4
1.2 Product Dimensions.....................................................................................4
1.3 Contents ......................................................................................................4
1.4 Specification ................................................................................................5
2.0 Overview..............................................................................................................6
3.0 Installation............................................................................................................7
4.0 Network Connection ...........................................................................................8

4
The Genie PWIP2BV is a 2MP IP IR bullet camera with a 2.8- 12mm varifocal lens. The camera
also features up to 50m IR night view distance as well as being IP67.
1.1 Product Features
• 2MP (1920 × 1080) H.265 coding
• Maximum resolution: 1920 × 1080
• ICR auto switch, true day / night, ROI coding
• 3D DNR, digital WDR, HLC, BLC, Defog
• 30~50m IR night view distance
• 1CH audio input, Hardware reset
• Built-in Micro SD card slot up to 128GB
• DC12V / PoE power supply
• IP67 ingress protection
• Supports mobile surveillance by smart phones and tablet PCs with iOS or Android OS
• Supports dual streams
• Intelligent analytics: video blur detection, line crossing detection and region intrusion
detection
1.2 Product Dimensions
1.3 Contents
1.0 Introduction
217.7mm
Camera Quick Start Guide 4 Tapping Screws PA 4×25
1 Machine Screw PWM3×5
CD Drill Template Rubber Plug Plastic Plug x4
80.5mm

Quick Start Guide 2MP H.265 IP IR Bullet Camera with 2.8-12mm Varifocal Lens
5
1.4 Specification
Camera
Image Sensor 1 / 2.9 “CMOS
Image Size 1920 × 1080
Electronic Shutter 1 / 25 s ~ 1 / 100000 s
Iris Type Fixed Iris
Minimum Illumination 0.0035 Lux @ F1.2, AGC ON, 0 Lux with IR
0.013 Lux @ F2.31, AGC ON, 0 Lux with IR
Lens 2.8~12mm @ F1.4, Horizontal field of view: 88°~34.8°
Lens Mount M12 or Φ14
Wide Dynamic Range Digital WDR
BLC Yes
HLC Yes
Digital NR 3D DNR
Angle Adjustment Pan: 0°~360°, Tilt: 0°~90°, Rotation: 0°~360°
Image
Video Compression H.265, H.264, MJPEG
H.265 Compression
Standard Main Profile @ Level 4.1 High Tier
Resolution 1080p (1920 × 1080), 720p (1280 × 720), D1, CIF, 480 × 240
Main Stream 60Hz : 1080p, 720p (1~30fps)
50Hz : 1080p, 720p (1~25fps)
Sub Stream 60Hz : D1, CIF, 480 × 240 (1~30fps)
50Hz: D1, CIF, 480 × 240 (1~25fps)
Bit Rate 64 Kbps ~ 6 Mbps
Bit Rate Type VBR / CBR
Audio Compression G711A / U
Image Settings ROI, Saturation, Brightness, Chroma, Contrast, Wide Dynamic, Sharpen,
NR, etc. Adjustable through client software or web browser
ROI Each ROI to be configured separately
Functions
Remote Monitoring Web browsing, CMS remote control
Online Connection Supports simultaneous monitoring for up to 3 users. Supports multi-
stream real time transmission
Network Protocol UDP, IPv4, IPv6, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, 802.1x, UPnP,
HTTPs, HTTP, QoS
Interface Protocol Onvif compatible
Intelligent Analytics
Video blur detection,
Line crossing detection,
Region intrusion detection
Storage Network remote storage, Micro SD card storage
Smart Alarm Motion detection, SD card error, SD card full
General Function Watermark, IP address filtering, video mask, heartbeat, illegal login
lock
PoE Yes
IR Distance 30 ~ 50 m
Interface
Network RJ45
Audio 1CH audio input
Storage Built-in Micro SD card slot, Up to 128GB
Hardware Reset Yes
Others
Ingress Protection IP67
Power Supply DC12V / PoE
Power Consumption < 7.5W
Operating Environment - 30 °C ~ 60°C (-22°F~140°F), Humidity: Less than 95% (Non-condensing)
Dimensions 217.7 × 80.5 × 80.5 mm
Weight Approximately 0.65Kg

6
2.0 Overview
Security Cap
DC12V
1. Fixed Ring
2. Mounting Base
3. Network Connector (It is recommended
to install the security cap for outdoor
installation)
4. Audio Input
5. Power Connector (If the PoE switch
is used to power the camera, DC12V
power supply is not required).
6. Micro SD Card Slot
7. Reset
1. Loosen the nut from the main element.
2. Run the network cable (without RJ 45 connector) through both elements. Then crimp
the cable with RJ 45 connector.
3. Connect the cable to the hermetic connector. Then tighten the nut and the main
cover.
Connecting Network Cable

7
Please make sure that the wall or ceiling is strong enough to withstand 3 times the weight
of the camera. Please install the camera in and under a dry environment.
1. Drill the screw holes and the cable hole on the wall according to the drill template.
2. Route and connect the cables.
3. Secure the mounting base with camera to the wall with the screws provided.
4. Bracket adjustment. Before adjustment, preview the image of the camera on a monitor
and then loosen the fixed ring to adjust the view angle of the camera.
5. Open the cover of the camera and then insert a micro SD card. After that, adjust Zoom
or Focus to obtain an optimum image (If the camera is fixed or motorised lens, please
skip this step). Before adjustment, preview the image of the camera on a monitor.
3.0 Installation
Rubber Plug
Fixed Ring
360° Pan
90° Tilt
Cover
Focus
Zoom
Insert a Micro
SD card
360° Rotation
6. Install the cover back to the
camera and fix it firmly with
the screws. (Note that the
cover should not be installed
unevenly).

8
Access the Camera through the IP Tool
1. Make sure that the camera and the PC are well connected via LAN.
2. Find the IP-Tool from the CD and then install it in the computer. After that, run the IP
Tool as shown below.
3. Modify the IP address. The default IP address of this camera is 192.168.226.201. Click the
information of the camera listed in the above table to show the network information
on the right hand. Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as that of the computer. Please
modify the IP address of your device according to the practical situation.
4. Double-click the camera listed in the IP-Tool or manually enter the IP address in
the address bar of the web browser to connect IP-CAM. Then follow directions to
download and install the plugin. Enter the username and password in the login
interface. The default username is admin; the default password is 123456.
4.0 Network Connection
For example, the IP address of your computer is 192.168.1.4. So the IP address of the
camera shall be changed to 192.168.1.X and the gateway shall be changed to 192.168.1.1.
After modification, please enter the password of the administrator and click “Modify”
button to modify the settings. The default password of the administrator is “123456”.

Sales [phone]
Enquiries [email protected]o.uk
Website www.genieproducts.co.uk