German pool HTS-200 User manual

Tower Fan Heater
直立式搖擺暖風機
HTS-200
在使用之前請詳細閱讀 「使用說明書」及「保用條例」
，並妥為保存。
Please read these instructions and warranty information carefully
before use and keep them handy for future reference.

產品結構 Product Structure 05
注意事項 Notice Before Use 03
操作說明 Operating Instructions 07
清潔與保養 Care & Maintenance 09
常見事故及處理 Troubleshooting 09
保用條款 Warranty Terms & Conditions 11
技術規格 Technical Specifications 10
目錄 Table of Contents
P.2

產品結構 Product Structure 05
注意事項 Notice Before Use 03
操作說明 Operating Instructions 07
清潔與保養 Care & Maintenance 09
常見事故及處理 Troubleshooting 09
保用條款 Warranty Terms & Conditions 11
技術規格 Technical Specifications 10
注意事項 Notice Before Use
重要說明
為安全起見，初次使用產品前請先細閱本說
 明書，並保存說明書，以便作參考之用。
 本產品只供家居使用。請必須依照本說明書
 內的指示安裝及操作。
Important
For safety purpose, you should read the instructions
carefully before using the appliance for the rst time.
Save the instructions for future reference.
The appliance is designed for domestic use and may
only be installed and operated in accordance with
these instructions for use.
P.3
1.風機應放置及使用於適當地方，切勿放置
  於電源插座底下。
2.切勿放置易燃及爆炸性物品於風機附近；
  切勿在充滿易燃氣體及塵粒的環境中使用
  風機。請遠離爐火及熱能。
3.風機應擺放於平穩的枱面或地面；切勿在
  浴缸、花灑或泳池附近使用風機。
4.電源線應妥為擺放，以免行走時被絆倒。
5.切勿讓電源線接觸過濾網，以免電源線被
  高溫燙斷。
6.切勿將濕的衣物放置於風機上或讓風機暴
  露於雨水。為免漏電，切勿將風機浸於任
  何液體之中。切勿以易燃物品及濕的衣物
  覆蓋過濾網，以免發生火警或觸電。
7.電流計及室內線路必須能夠負載風機之電
  力，並須同時考慮其他電器的負載。
8.切勿在風機運作時觸摸過濾網，以免皮膚
  被高溫燙傷。
9.切勿在風機運作時拆除過濾網。
10.不使用風機時，必須拔下電源插頭。切勿
  用手拔除電源線。拔出電源插頭前應先關
  掉風機。
1. The fan heater should be placed and used in an
appropriate place. Do not place it under the power socket.
2. Do not place ammable and explosive articles
near the fan heater. The fan heater can not be
used in any environment lled with ammable gas
and dust. Please keep heater away from open re
and heat.
3. The fan heater should be put on a stable and level
tabletop or ground. Do not use the fan heater in
immediate surroundings of a bathroom, shower
nozzle or swimming pool.
4. The supply cord should be placed well in order to
prevent tripping over while walking.
5. Never let the supply cord touch the ltration net to
avoid scalding the cord at high temperature.
6. Do not hang wet laundry above the fan heater or
allow it to be caught in the rain. To avoid the
danger of electricity leaks, do not immerse heater
in any liquid. Do not cover the ltration net with
ammable articles and wet clothes in order to
prevent re hazards or electric shock.
7. Ammeter and indoor wiring must be able to load
the power of the fan heater. In addition, the loads
of other appliances should be considered at the
same time.
8. Do not touch the ltration net while the fan heater
is operating in order to avoid burns.
9. Do not dismantle the ltration net when the fan
heater is operating.
10. When the fan heater is not being used, remove
power plug from the power socket. Do not unplug
the supply cord with hands. Always turn off the fan
heater before unplugging.

注意事項 Notice Before Use
P.4
11.長期不使用風機時應放回包裝盒並存放於
 乾爽通風的位置。
12.本風機不適宜給兒童或身體狀況有礙安全
 使用之人士獨自使用。應看守兒童，以免
 他們用作玩耍。
13.切勿將傳導性物品插入過濾網的前面或後
 面。切勿觸摸帶電的零件以免觸電。
14.切勿在無人看管的情況下開著風機，以免
 發生意外。
15.如電源線損壞或其他問題出現，必須由本
 公司維修部或合資格的技術人員更換及處
 理。切勿自行拆除這些部件及更換不符合
 安全規格的配件。
16.電壓與頻率應與風機之技術規格相符。
17.若風機被放置於零下20度的環境中，使用
 時必須將溫度略為提高後才啓動風機，以
 免物料因過於低溫而變質，影響電器的安
 全性。
18.進風面保持於背面，出風面保持於正面，
 切勿遮蓋風機。
11. The fan heater should be packed well when not
used for a long time to keep away from dust. Then,
store at dry, ventilated place.
12. The fan heater is not intended for use by children or
persons with physical conditions that prevent them
from using it safely. Children should be supervised
to ensure that they do not play with the appliance.
13. Do not insert into the front and back of the ltration
net with conductive articles. Do not touch electrical
components with bare hands in order to avoid
electric shock.
14. For safety reason, do not use the fan heater without
anyone’s presence to avoid accidents.
15. If the supply cord is damaged or other troubles
appear, please contact our Repair Centre or
qualied technicians for help. Do not dismantle
these parts by yourself. Do not replace with ttings
which do not comply with the security regulations.
16. Power voltage and frequency should accord with
the main technical parameter requirement of the
fan heater.
17. If the fan heater is placed in an environment with
20 degrees below zero, the room temperature
must be risen to a higher temperature before
turning on the fan heater. This is to prevent the
material from a change of nature due to
hypothermia, which will accordingly affect the
security of the product.
18. Keep the inlet net on the back and outlet net
expedite. Do not cover the fan heater.

產品結構 Product Structure
P.5
Front:
1. Control Panel
2. Front Cover
3. Heater Support Stand
4. Glass Base
5. Frame
Back:
6. Handle
7. Air Filter Grille Cover
8. Main Power Switch
9. Securing Nut
10. Power Cord
11. Base Support
機身正面：
1.操作面板
2.出風口保護殼
3.支撐柱
4.玻璃底座
5.裝飾框
機身背面：
6.手柄
7.過濾網保護蓋
8.電源開關
9.組裝旋鈕
10.電源線
11.底座腳
(5)
機身 Body
(1)
(6)
(7)
(8)
(9)
(2)
(3)
(11)
(10)
(4)

產品結構 Product Structure
P.6
顯示屏 Display
按鍵 Control Buttons
遙控器 Remote Control
搖擺
Swing
熱力強弱
Heating Power
熱力強弱Heating Power
開關顯示
ON/OFF Display
搖擺顯示
Swing ON/OFF
Display
熱力設定顯示
Heat Setting Display
定時設定顯示
Timer Setting Display
開關ON/OFF
定時Timer搖擺Swing
定時
Timer
開關
ON/OFF

操作說明 Operating Instructions
P.7
Assembly of Device
1. Place the Main Body horizontally on a table. Unscrew
the Securing Nut (Fig 1).
2. Insert the Glass Base into the Heater Support Stand.
Use the Securing Nut to screw it tightly (Fig 2).
3. Place the device upright on an even and stable oor
(Fig 3).
Operating Procedures
1. Main Power Switch
- Connect the appliance to the power supply. Make
sure the power voltage and frequency accords with
the requirement of the heater.
- Press the Main Power Switch at the back of the fan
heater. A sound will be heard, which means the
device is in Standby status.
2. On/Off
- Under the condition of Standby, only is available
to be pressed. Press once to turn on the device,
press again to turn off.
3. Heating Power
- Press to adjust the heating power.
- On the display, 1,200W indicates low heat. 2,000W
means high heat.
安裝程序
1.將主機平放桌面，扭開組裝旋鈕(圖1)。
2.將玻璃底座套進主機支撐柱，重新扭緊旋
鈕(圖2)。
3.豎起本機，放在平穩的地面上(圖3)。
操作程序
1.總電源開關
-檢查插座電壓符合產品使用電壓後，插
上電源。
-開啟機身背面的總電源開關，發出「嗶
嗶」聲響即表示已進入待機狀態。
2.開關
-在待機狀態下，除鍵外，其他按鍵暫
時無效，按鍵開機，再按一次關機。
3.強弱
-開機狀態下，按鍵切換熱力強弱。
-指示燈顯示1,200W指低熱，2,000W指高熱。
圖1Fig 1 圖2Fig 2 圖3Fig 3
主機
Main Body
主機
Main Body
玻璃底座
Glass Base
組裝旋鈕
Securing Nut
組裝旋鈕
Securing Nut

操作說明 Operating Instructions
P.8
4. Timer
- Press to set timer.
- Press the key once will increase the timer setting by
0.5 hrs. For example: when 0.5 and 1.0 both light
up, it means timer is set to 1.5 hrs. When 1.0 and
2.0 both light up, it means timer is set to 3 hrs, and
so on. The maximum timer setting is 7.5 hrs.
- When the timer is set to 7.5 hrs, press once more to
cancel the timer.
- The fan heater will stop running and enter Standby
status after timing is over.
5. Swing
- Press to switch the swinging function. Swing
ON/OFF Display lights up when the swinging
function is on.
6. Remote Control
- Open the cover at the back of the remote control
and insert a battery.
- There are 4 function keys on the remote control
and their functions are same as those keys on the
control panel of the heater.
- Point the remote control to the display window of the
heater when using the remote control.
4.定時
-按鍵定時。
-每按一次累增半小時。如顯示屏上0.5及
1.0同時亮起，表示定時設定為1.5小時，
如1.0及2.0同時亮起，表示3小時，如此
類推，最多可設定至7.5小時。
-增至7.5小時後，再按一次會回復為無定
時狀態。
-定時設置後立即開始計時，過了指定時
間後，風機會自動停止送風，回復待機
狀態。
5.搖擺
-開機狀態下，按鍵切換搖擺功能。搖
擺功能啟動期間，搖擺指示燈會亮起。
6.遙控器
-打開遙控器背面的電池格，放進電池。
-遙控器上有4個按鍵，功能與機身操作面
板上的按鍵完全一樣。
-使用時請對準機身的遙控接收器。

清潔與保養 Care & Maintenance
P.9
常見事故及處理 Troubleshooting
- 清潔或維修前必須先拔出電源插頭，並等待
機身冷卻。
- 以軟布清潔機身表面的塵埃，若仍未能清除
污跡，可用軟布沾上低於50℃的清水(混和
中性清潔劑)清潔污跡，然後晾乾。
- 請清潔設於機身背面內部的過濾網，按解鎖
扣以拆除過濾網，然後用溫水(以低於30℃
的溫水混和一般洗衣粉)清洗。
- 切勿以汽油、稀釋劑或任何腐蝕性物質清潔
風機表面。
- 待風機完全冷卻、放乾，並妥為包裝後，才
可收藏，並請存放於通風處。
- Before cleaning or repairing, always disconnect the
fan heater from the electrical supply. Please let the
fan heater cool down before maintenance.
- If there is dust on the surface, please clean with a
soft cloth. If stains remain, dip cloth in water lower
than 50oC (mixed with mild soap) to clean the smut
and then let it dry.
- Please clean the air filter at the back of the fan
heater. Press the Unlock Button to remove the
filter, and then wash it with warm water (lower than
30oC, mix with normal washing powder).
- Do not clean the appliance with gasoline, thinner
or abrasive materials can damage the surface of
fan heater.
- To store the appliance, please pack after the fan
heater has cooled down completely and is dry.
Please place the fan heater at an aerated place.
- 在風機傾側、底部脫離地面或地面不平坦的
情況下，防傾斜保護掣會啟動。此時，嘗試
將風機擺放於平坦的表面，然後再次啟動。
- 若風機處於高溫環境下，自動調溫器可能會
中斷電源以保安全。待風機冷卻後，便會繼
續操作。
-若遙控器沒有操作反應，嘗試將它對準接收
器，再次按鍵。若暖風機仍沒有反應，請更
換電池。
- 如上述問題持續或出現其他問題，請聯絡或
送回本公司維修部進行維修。
- The tip-over protection switch will cut off the electric
supply. If the appliance is tilted, the base deviates
from the ground or the ground is not flat. In this
case, place the fan heater at the flat place and turn
it on again.
- The thermostat may cut off the power automatically
for safety, if the fan heater is used in a surrounding
with high temperature. The appliance may resume
work when the fan heater cools down.
- If the remote control does not work well, try to adjust
the direction so that the remote control transmitter is
pointed to the receiver directly. Replace the battery
when the fan heater has no response.
- If the problems persist or other problems occur,
contact our Repairs Centre for repair.

技術規格 Technical Specications
P.10
保用條款
此保用提供德國寶產品之機件在正常使用下壹年
保用(自購買日起計算)。
Warranty Terms & Conditions
Under normal operations, the product will receive a 1-year full
warranty provided by German Pool (effective starting from the
date of purchase).
1. Customer who fails to present original purchase invoice
will be disqualified for free warranty.
2. Customer should always follow the operating
instructions. This warranty does not apply to:
- labour costs for on-site installation, check-up, repair,
replacement of parts and other transportation costs;
- damages caused by accidents of any kind (including
transport and others);
- plastic parts and accessories;
- operating failures resulted from incorrect voltage,
improper operations and unauthorized installations
or repairs.
3. This warranty is invalid if:
- purchase invoice is modified by unauthorized party;
- product is used for any commercial or industrial applications;
- product is repaired or modified by unauthorized
personnel, or unauthorized parts are installed;
- serial number is modified, damaged or removed from
the product.
4. German Pool will, in its discretion, repair or replace any
defective part.
5. This warranty will be void if there is any transfer of
ownership from the original purchaser.
1. 未能出示購買發票正本者，將不獲免費維修服務。
2. 用戶應依照說明書的指示操作。本保用並不包括﹕
- 上門安裝、檢驗、維修或更換零件之人工以及一
切運輸費用﹔
- 因天然與人為意外造成的損壞(包括運輸及其他)﹔
- 任何塑膠附件及輔助裝置﹔
- 電源接合不當、不依說明書而錯誤或疏忽使用本
機所引致之損壞。
3. 於下列情況下，用戶之保用資格將被取消﹕
- 購買發票有任何非認可之刪改；
- 產品被用作商業或工業用途；
- 產品經非認可之技術人員改裝或加裝任何配件；
- 機身編號被擅自塗改、破壞或刪除。
4. 總代理有權選擇維修或更換配件或其損壞部份。
5. 產品一經被轉讓，其保用即被視作無效。
機身號碼 Serial No. :
購買商號 Purchased From :
發票號碼 Invoice No. :
購買日期 Purchase Date :
型號 Model No. :
請填妥以下空格並與發票一併保存¸以便維修時核對資料。用戶提供本公司之所有資料必須正確無誤¸否則免費保用將會無效。
Please fill out the form below. This information and the purchase invoice will be required for any repairs. Warranty will be invalid
if information provided is found to be inaccurate.
HTS-200
P.19
* 貴戶須在購機十天內，以下列其中一種方
式向本公司登記資料，保用手續方正式生效﹕
1)填妥本公司網頁內之保用登記表格
www.germanpool.com/warranty。
2)填妥保用登記卡，並連同購機發票之副本一
併郵寄到客戶服務部 (本公司將不發還發票
副本或登記卡)。
* This warranty is not valid until Customer’s registration
information is returned to and received by our Service
Centre within 10 days of purchase via one of the
following methods:
1) Visit our website and register online:
www.germanpool.com/warranty.
2) Completeall fields on the attached Warranty Card and
mail itback to our Customer Service Centre along with
a photocopy of the purchase invoice (Warranty Card
and invoice copy will not be returned to Customer).
產品規格及設計如有變更﹐恕不另行通知。
Specications are subject to change without prior notice.
中英文版本如有出入，一概以中文版為準。
If there is any inconsistency or ambiguity between the English version and the Chinese version, the Chinese version shall prevail.
型號 Model HTS-200
電壓 Voltage 220-240 V
頻率 Frequency 50Hz
功率 Rated Power 2,000 W
定時 Timer 0.5 - 7.5 hrs
機身尺寸 Dimensions (H) 646 mm (W) 230 mm (D) 230 mm

保用條款
此保用提供德國寶產品之機件在正常使用下壹年
保用(自購買日起計算)。
Warranty Terms & Conditions
Under normal operations, the product will receive a 1-year full
warranty provided by German Pool (effective starting from the
date of purchase).
1. Customer who fails to present original purchase invoice
will be disqualified for free warranty.
2. Customer should always follow the operating
instructions. This warranty does not apply to:
- labour costs for on-site installation, check-up, repair,
replacement of parts and other transportation costs;
- damages caused by accidents of any kind (including
transport and others);
- plastic parts and accessories;
- operating failures resulted from incorrect voltage,
improper operations and unauthorized installations
or repairs.
3. This warranty is invalid if:
- purchase invoice is modified by unauthorized party;
- product is used for any commercial or industrial applications;
- product is repaired or modified by unauthorized
personnel, or unauthorized parts are installed;
- serial number is modified, damaged or removed from
the product.
4. German Pool will, in its discretion, repair or replace any
defective part.
5. This warranty will be void if there is any transfer of
ownership from the original purchaser.
1. 未能出示購買發票正本者，將不獲免費維修服務。
2. 用戶應依照說明書的指示操作。本保用並不包括﹕
- 上門安裝、檢驗、維修或更換零件之人工以及一
切運輸費用﹔
- 因天然與人為意外造成的損壞(包括運輸及其他)﹔
- 任何塑膠附件及輔助裝置﹔
- 電源接合不當、不依說明書而錯誤或疏忽使用本
機所引致之損壞。
3. 於下列情況下，用戶之保用資格將被取消﹕
- 購買發票有任何非認可之刪改；
- 產品被用作商業或工業用途；
- 產品經非認可之技術人員改裝或加裝任何配件；
- 機身編號被擅自塗改、破壞或刪除。
4. 總代理有權選擇維修或更換配件或其損壞部份。
5. 產品一經被轉讓，其保用即被視作無效。
機身號碼 Serial No. :
購買商號 Purchased From :
發票號碼 Invoice No. :
購買日期 Purchase Date :
型號 Model No. :
請填妥以下空格並與發票一併保存¸以便維修時核對資料。用戶提供本公司之所有資料必須正確無誤¸否則免費保用將會無效。
Please fill out the form below. This information and the purchase invoice will be required for any repairs. Warranty will be invalid
if information provided is found to be inaccurate.
HTS-200
P.19
* 貴戶須在購機十天內，以下列其中一種方
式向本公司登記資料，保用手續方正式生效﹕
1)填妥本公司網頁內之保用登記表格
www.germanpool.com/warranty。
2)填妥保用登記卡，並連同購機發票之副本一
併郵寄到客戶服務部 (本公司將不發還發票
副本或登記卡)。
* This warranty is not valid until Customer’s registration
information is returned to and received by our Service
Centre within 10 days of purchase via one of the
following methods:
1) Visit our website and register online:
www.germanpool.com/warranty.
2) Completeall fields on the attached Warranty Card and
mail itback to our Customer Service Centre along with
a photocopy of the purchase invoice (Warranty Card
and invoice copy will not be returned to Customer).

HTX-HTS200-M-11(1)
德國寶(香港)有限公司
German Pool (Hong Kong) Limited
© 版權所有。未獲德國寶授權，不得翻印、複製或使用本說明書作任何商業用途，違者必究。
© All rights reserved. Copying, reproducing or using the contents of this manual is not allowed without prior authorization from German Pool, violators will be prosecuted.
香港總代理Hong Kong Sole Agent中國總代理China Sole Agent
九龍土瓜灣馬頭角道116號新寶工商中心高層地下2-4號室
Room 2-4, Upper G/F, Newport Centre, 116 Ma Tau Kok Road,
Tokwawan, Kowloon
電話 Tel: [phone] 傳真 Fax: [phone]
廣東省佛山市順德區南國東路永旺 (吉之島) 購物中心3樓
3/F, Yongwang (Jusco) Shopping Mall, Nanguo East Road,
Shunde, Foshan, Guangdong
電話 Tel: [phone] 傳真 Fax: [phone]