Gigaset C430 User manual

Gigaset_C430-C430A/C530-C530A KBA für UK _ A31008-M2502-L101-1-7643 _ May 16, 2013
Pack contents
If you have purchased a model with
multiple handsets, the package
should contain two batteries, one
battery cover, one belt clip and one
charger 9 with a power adapter J
for each additional handset.
1
1one Gigaset Base station
2one power adapter for the base
3one Gigaset handset
4one phone cord
5two batteries
6one battery cover
7one belt clip
8one user guide plus one quick start
guide
2
3
67
4
5
8
C430A-C530A C430-C530
9J
Connecting the base station
¤Insert the phone cable into the
connection socket 1 at the rear of
the base until it clicks into place and
feed under the cable protection.
¤Insert the power cable for the
power adapter into the connection
socket 2 at the rear of the base and
rotate the right-angle plug under
the cable protection.
¤Connect the power adapter 3.
¤Connect the phone jack 4.
Please note:
¤The power adapter must always be
connected, as the phone will not
operate without a power supply.
¤Use only the power adapter and
phone cord supplied. Pin
connections on telephone cables
can vary.
Connecting the handset charger (if included)
1
2
34
C430A-C530A
C430-C530
1
2
¤Connect the flat plug to the charging cradle1.
¤Plug the power adapter into the power socket2.
If you have to remove the plug from the charger
again:
¤Disconnect the power adapter from the mains
power supply.
¤Press the release button 3and disconnect the
plug4.
1
3
4
2
Frequently asked questions
Q: There is no dial tone.
A: Press call button for 2 seconds (long press) to obtain dial tone.
A short press opens the redial list.
Q: The line is crackling / not clear.
A: Have you used the new line cable provided? Please do not use an old cable.
Q: The display is not clear / seems to be broken.
A: The display is protected by a plastic film, please make sure you have removed
the protective film.
Q: The handset is not registered.
A: If your handset is not registered, please follow the Registration handset procedure.
(see user manual)
Q: The caller ID is not working.
A: Have you subscribed to this service (CLIP) from your provider?
Q: Message indicator flashing and I cannot retrieve my message.
A: Message indicator will flash to indicate missed calls as well as new messages of text mes-
sages. (see user manual)
Please check:
Have you used the phone cord supplied
Have you fully inserted the power cable into the base station
Have you inserted the batteries correctly
Have you charged the battery for 8.5 hours
Have you set up the Date/Time
To download the latest manuals, visit our web-site: http://www.gigaset.com
If you have problems setting up or operating this product please call
GIGASET UK HELPLINE 084503 18190
GIGASET IRL HELPLINE 0818 200 033
Issued by
Gigaset Communications GmbH
Frankenstr. 2a
D-46395 Bocholt
© Gigaset Communications GmbH 2013
All rights reserved. Subject to availability.
Rights of modification reserved.
www.gigaset.com
Preparing the handset
Charging the battery
The battery is supplied with a partial charge. Please charge it completely before use.
¤Charge the handset in the base for 8.5 hours.
Please note
The handset must only be placed in the designated base or charger.
¤Insert the batteries
with the polarity in
the right direction
(for correct +/-
direction, see
diagram).
¤First insert the battery
cover on the top 1.
¤Then press the cover
2until it clicks into
place.
To open the battery cover,
for example to change the
batteries:
¤Grip the notch on the
cover 3and slide it
downwards 4.
1
3
4
2
C430A-C530A C430-C530
8.5 h 8.5 h
Setting the date and time
Set the date/time so that the correct date and time can be assigned to incoming calls, and so
that you can use the alarm.
Date/Time
Date:
14.10.2013
Time:
07:15
Back Save
Calls Time
¤Press the key Time below the display screen to
open the input field.
(If you have already set the date/time, open the
input field via the menu:
v¤Ï¤OK ¤Date/Time ¤OK)
The submenu Date/Time is shown on the display.
¤The active input position flashes.
Enter the day, month and year as an
8-digit number via the keypad,
e.g. 4Q2Q3
for 14.10.2013.
Press the right or left control key to
change the input position, e.g. to
correct an entry.
¤Press the down control key to switch to the
time input field.
¤Enter the hours and minutes in 4-digit format
via the keypad e.g., QM5for
07:15 am.
Change the input position with the control key
if necessary.
¤Press the key Save below the display screen to
save the entry.
Date/Time
Date:
15.01.2013
Time:
00:00
Back Save
Handset registration
Handsets contained in the package have already been registered to the base.
If, however, a handset has not been registered (display "Please register handset" or "Place
handset in base"), you must register it to the base.
if your handset is flashing the text "No Base" then it can be that:
uYour base station is not switched on, please check if the power supply is connected
properly.
uThere is too much distance between the handset and the base.
If the handset has not been pre-registered or you want to register an additional handset
to your base station, use the registration procedure below.
uAutomatically registering the Gigaset C430-C530
handset to base station:
¤Place the handset in the base.
If automatic registration does not work, the handset
will have to be registered manually.
uManually registering the handset:
¤On the base: Press and hold (min. 3 seconds) the
Registration/paging key 1.
¤On the C430-C530 handset, press the display key
Register.
Or:
v¤Ï¤OK ¤qRegistration ¤OK
¤Register Handset ¤OK
Display shows: Searching for a base in registration mode.
The connection to the base will be established; this may
take some time.
¤Enter the system PIN if required (factory setting: 0000)
¤OK
You can register up to six handsets to your base. You can
also register other Gigaset handsets and handsets from
other devices with GAP functionality.
Dial Tone
The dial tone will only be heard when pressing the call button cfor 2 seconds. A short press
will open the redial list.
C430A-C530A
C430-C530
1
1
Message lists
Any messages you receive are saved in the message lists. An
advisory tone sounds as soon as a new entry appears on a list.
The Message key also flashes. Icons for message types and the
number of new messages are shown on the idle display.
New messages available:
uÃOn the answer machine (only C430A-C530A)/
network mailbox
u™In the missed calls list
uIn the missed alarms list
Open the message list by pressing the Message key f.
Answer machine
Activating/deactivating the answer machine
v¤Ì¤OK ¤qActivation (μ= activated) ¤Change
¤Activation: rOn / Off
If activated:
¤Mode:
rAnswer & record / Answer only / Alternating
–Answer & record: The caller can leave a message;
–Answer only: The caller only hears an announcement
and cannot leave a message;
–Alternating:
If activated, Record from: s/ Record until: Enter the
length of time in which messages are recorded.
¤Save
i à V
07:15
INT 1 14 Oct
Ù
02 10 08
Calls Calendar
Example
Answer Machine
Activation:
On
Mode:
<Alternating >
Record from:
08:00
x
Back Save
Example
Congratulations
By purchasing a Gigaset, you have chosen a brand that is
fully committed to sustainability.
This product’s packaging is eco-friendly!
To learn more, visit www.gigaset.com.
C430 -C430A
C530 -C530A
Quick Start Guide
GIGASET HELPLINE: 084503 18190