Gilson Power Carrousel User manual

User’s Guide
EN

TABLE OF CONTENTS
TABLE OF CONTENTS | POWER CARROUSELTM
TABLE OF CONTENTS
INTRODUCTION | 3
Parts Checklist | 3
SAFETY |3
Safety at Work | 4
Electrical Specifications | 4
AC Adaptor | 4
Changes in Configuration/Design by User | 4
GETTING STARTED |5
Installation of Power Carrousel | 5
Battery charging of PIPETMAN M and PIPETMAN M Connected pipettes by using POWER
CARROUSEL | 5
CLEANING, DECONTAMINATION, AND MAINTENANCE |6
Cleaning and Decontamination | 6
Maintenance | 6
TECHNICAL DATA SHEET |7
Equipment Disposal: (WEEE 2002/96/EC) | 7
EC—DECLARATION OF CONFORMITY |7

INTRODUCTION
3
POWER CARROUSELTM |USER’S GUIDE
Chapter 1
INTRODUCTION
Congratulations on the purchase of POWER CARROUSEL™, a multi-charging pipette
stand designed to be used with all models of PIPETMAN® M and PIPETMAN® M Connected
pipettes.
Parts Checklist
Just take a moment to verify that the following items are present:
• POWER CARROUSEL,
• Power Supply 5V with AC adapter and cable,
• POWER CARROUSSEL User’s Guide LT801541.
MODEL PART NUMBER
POWER CARROUSEL FB1001
NOTICE
NOTICE indicates a potentially hazardous situation which, if not avoided,
may result in equipment damage.
WARNING
WARNING indicates a potentially hazardous situation which, if not
avoided, may result in serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
Chapter 2
SAFETY
All persons working with POWER CARROUSEL must read the operating and safety
instructions before operating the instrument.
For safety reasons, it is important to observe the following instructions.

SAFETY
4SAFETY | POWER CARROUSELTM
Safety at Work
In addition to any safety precautions listed here, all other relevant safety aspects –e.g., GLP,
GMP, professional trade associations, Department of Health, trade supervisory authorities –
must be observed.
Electrical Specifications
POWER CARROUSEL is supplied with an AC adaptor that is suitable for your country.
You must only use an original Gilson AC adaptor specific to this product.
POWER CARROUSEL is used to recharge Gilson PIPETMAN M and PIPETMAN M Connected
pipettes with a battery specified by Gilson. Use AC adaptor and stand adapter indoors.
AC Adaptor
Input voltage, country-specific: 100–240 V, 50/60 Hz (0.6A max.)
Output voltage: +5 V DC; 3A (15W max.)
Class II: this device is double insulated.
Gilson will not take any responsibility if a non-specified AC adaptor is used.
The look of the reel at the bottom of the carrousel stand is due to an anti-corrosion
treatment (refer to Figure 1).
Use POWER CARROUSEL only with original Gilson’s PIPETMAN M and PIPETMAN M Connected.
If the equipment is used in a manner not specified by Gilson in the user’s guide, the
protection provided in the equipment may be impaired.
Changes in Configuration/Design by User
No changes may be made to POWER CARROUSEL. Any parts that become defective must
be replaced by original Gilson parts.
POWER CARROUSEL may not be altered in design or in any of their safety aspects without
the express written permission of Gilson. In particular, no alterations may be made to any
of the protective functions. Any alteration releases Gilson from any liability for damage
caused.
POWER CARROUSEL is not protected against liquids.
Do not immerse POWER CARROUSEL; liquid inside can damage its internal
components.
Do not allow the liquid to enter the body of POWER CARROUSEL.
WARNING
Do not use POWER CARROUSEL in a potentially explosive environment or with
potentially explosive chemicals.
Do not position pipettes on POWER CARROUSEL if they can touch each other,
this may create contamination on the pipettes.

GETTING STARTED
5
POWER CARROUSELTM |USER’S GUIDE
Chapter 3
GETTING STARTED
Installation of POWER CARROUSEL
1. Place POWER CARROUSEL on the bench.
2. Connect the AC adaptor to a suitable AC power supply. The cable is stored on the
bottom side of the carrousel and can be unrolled and rolled as required (see Figure 1).
3. The carrousel is ready to charge PIPETMAN M pipettes.
Battery Charging of PIPETMAN M and PIPETMAN M
Connected by Using POWER CARROUSEL
1. First install POWER CARROUSEL as described above.
2. Remove the plug (refer to Figure 3). Now place your
pipette on the charging position (refer to Figure 4),
please ensure that the pipette is properly fitted to
the contacts on the top of the carrousel (a proper
fitting will trigger a beep sound).
3. The pipette will start charging. PIPETMAN M and
PIPETMAN M Connected charges 80% of its full battery
capacity in less than an hour, it takes three hours
to fully charge the battery (for further information
on PIPETMAN M or PIPETMAN M Connected power
management please refer to PIPETMAN M and
PIPETMAN M Connected User’s Guides located on
www.gilson.com).
Figure 3
PIPETMAN® M and
PIPETMAN® M Connected plug
Figure 4
Charging position
Make sure that POWER CARROUSEL
is well positioned on the bench.
Do not use POWER CARROUSEL
on an unbalanced surface or with
inaccurately rolled cable.
NOTE
It’s recommended to properly balance
the pipettes on the carrousel to
guarantee perfect stability
(refer to Figure 2).
Figure 2
POWER CARROUSELTM
Figure 1
POWER CARROUSELTM bottom side
WARNING
Do not use POWER CARROUSEL in a potentially explosive environment or with
potentially explosive chemicals.

CLEANING, DECONTAMINATION, AND MAINTENANCE
6CLEANING, DECONTAMINATION, AND MAINTENANCE | POWER CARROUSELTM
Chapter 4
CLEANING, DECONTAMINATION, AND
MAINTENANCE
Cleaning and Decontamination
• To clean POWER CARROUSEL, wipe it with a soft-cloth or lint-free tissue dipped in a
simple soap solution or 70% Ethanol, to remove all marks. If POWER CARROUSEL is
very dirty, a brush with soft plastic bristles may be used.
• To rinse, wipe POWER CARROUSEL with a soft cloth or lint-free tissue dipped in
distilled water.
• Allow it to air-dry or dry it carefully with a soft-cloth or lint-free tissue.
If you use chemical solutions for decontamination or detergents for cleaning other than
those specified below, you should check with your supplier that the solution or detergent is
safe for use with the following materials: polypropylene, steel, rubber.
Maintenance
POWER CARROUSEL must be cleaned regularly. If necessary, you can replace:
Do not autoclave POWER CARROUSEL. Extreme heat will damage electronic
components.
Do not immerse POWER CARROUSEL. Liquid inside will damage its internal
components.
MODEL PART NUMBER
The antiskid rubber feet 5462105001
Power supply FB07001
POWER CARROUSEL must not be opened. Repairs must be carried out by Gilson
or a service company authorized by Gilson.
Please contact your local Gilson representative for the replacement of spare parts.

TECHNICAL DATA SHEET
7
POWER CARROUSELTM |USER’S GUIDE
Chapter 6
EC—DECLARATION OF CONFORMITY
POWER CARROUSEL complies with the requirements of the following safety standards:
Standards for UE
• 2014/30/EU Electromagnetic Compatibility
• 2014/35/EU Low Voltage Directive
• 2015/863/EU Restriction of Hazardous Substances
• Directive REACH
Standards for UK
• Electromagnetic Compatibility, Regulation 2016, BS EN Standard 61326-1
• Electrical Equipment (Safety), Regulation 2016, BS EN Standard 61010-1
Chapter 5
TECHNICAL DATA SHEET
Dimensions (LxH): 15 cm (socket)/18 cm (rosette) x 40 cm
Weight: 895 g
AC Adapter: Input: 100–240V ~ 0.6A - 50–60Hz
Output: 5V DC 3.0A
Indoor use only.
Temperature: Storage: -10°C to +50°C
Operating: +4°C to +40°C
Humidity max: 80%
Operating Temperature: Between +4°C and +40°
Humidity: 20%–80%
Air pressure: 800–1200 mbar
UV-resistance: If POWER CARROUSEL is exposed
to ultraviolet light, the plastic housing might
discolor and become slightly yellow. This will
not aect functioning eciency of the device.
Equipment Disposal: (WEEE 2002/96/EC)
This equipment must not be disposed of with unsorted municipal waste. Instead,
it is your responsibility to correctly dispose of your waste equipment by handing
it over to an authorized facility for separate collection and recycling. It is also your
responsibility to decontaminate the equipment in case of biological, chemical, and/
or radiological contamination so as to protect from health hazards the persons involved in
the disposal and recycling of equipment. For more information about where you can drop
off your waste equipment for recycling, please contact your local dealer from whom you
originally purchased the product or your local council. By doing so, you will help conserve
natural resources and you will ensure that your waste equipment is recycled in a manner
that protects human health and the environment. Thank you.

gilson.com/contactus
LT801541/C | ©2022 Gilson, Inc. All rights reserved.