Beninca THINK-I User manual

THINK
L8542632
03/2012 rev 5
UNIONE NAZIONALE COSTRUTTORI
AUTOMATISMI PER CANCELLI, PORTE
SERRANDE ED AFFINI
THINKTHINK-PTHINK-I

DL1
8k2
DAS
109
8
3435363738
394041
7
230Vac 50Hz
400Vac 50Hz
P.P. COM PED. OPEN CLOSE STOP
3130
RADIO
T1A
F1
T0,5A T0,125A
T2A
F2
F3 F4
SWO (Open)
SWC (Close) PHOT 1 PHOT 2 PHOT 3
24Vac/0,5A
230Vac/0,5A
PHOT 4 COM
3332
TS
N
R
L
COM
M
C
123 123
U V W
M
363738 363738
230Vac 400Vac
DAS
J2 DAS
Open
DAS N.C.
J2 DAS
Close
DAS 8K2
34 35
22 27
SAFETY
STOP
C AUX
LAMP
230Vac
SCA/Phototest
18171615141312 2019 21 2211 23 24 25 26 27 28 29
109
F
L N
Service
Light
230V
2 31 5 64
3130
3332
RX
2 CH.
SHIELD
ANT
ANT
1 Phase
8k2
DAS
P.P. COM PED. OPEN CLOSE STOP
SWO (Open)
SWC (Close) PHOT 1 PHOT 2 PHOT 3
24Vac/0,5A
PHOT 4 COM
SCA/Phototest
18171615141312 2019 21 2211 23 24 25 26 27 28 29
THINK

3
24Vac 24Vac COM NC
RX1 TX1
24Vac - 12 24Vac - 11
COM - 15
PHOT 1 - 18
24Vac 24Vac COM NC
RX3 TX3
Photo TEST - 14 Photo TEST - 13 Photo TEST - 14 Photo TEST - 13
Photo TEST - 14 Photo TEST - 13 Photo TEST - 14 Photo TEST - 13
24Vac - 12 24Vac - 11
COM - 15
PHOT 3 - 20
24Vac 24Vac COM NC
RX2 TX2
24Vac - 12 24Vac - 11
COM -15
PHOT 2 - 19
24Vac 24Vac COM NC
RX4 TX4
24Vac - 12 24Vac - 11
COM - 15
PHOT 4 - 21
18171615141312 2019 21 2211 23 24 25 26 27 28 29
PHOT 1 PHOT 2 PHOT 3 24Vac PHOT 4 COM Phototest
Collegamento dispositivi di sicurezza verificati / Connection of tested safety devices
Anschluss geprüfter Sicherheitsvorrichtungen / Branchement dispositifs de sécurité vérifiés
Conexión de los dispositivos de seguridad verificados / Połączenia sprawdzanych urządzeń bezpieczeństwa

10
WARNINGS
This manual has been especially written to be use by qualified
fitters.
None of the information provide in this manual can be consi-
dered as being of interest for the end users.
Preserve this manual for future needs.
The technician has to furnish all the information related to the
step by step function, the manual and the emergency function
of the operator, and to deliver the manual to the final user.
cForesee on the supply net an onnipolar switch or
selector with distance of the contacts equal or
superior to 3 mms.
Verify that of the electrical system there is an awry differential
interrupter and overcurrent protection.
Some typologies of installation require the connection of the
shutter to be link at a conductive mass of the ground according
to the regulations in force.
The electrical installation and the operating logic must comply
with the regulations in force.
The leads fed with different voltages must be physically
separate, or they must be suitably insulated with additional
insulation of at least 1 mm.
The leads must be secured with an additional fixture near
the terminals.
During installation, maintenance and repair, interrupt the
power supply before opening the lid to access the electrical
parts
Check all the connections again before switching on the
power.
The unused N.C. inputs must be bridged.
The descriptions and the present illustrations in this manual
are not binding. Leaving the essential characteristics of the
product unchanged, the manufacturer reserves himself the
right to bring any change of technical, constructive or com-
mercial character without undertaking himself to update the
present publication.
CE Declaration of Conformity
Declaration in accordance with Directives 2004/108/CE (EMC); 2006/95/CE (LVD)
The Manufacturer:
Automatismi Benincà SpA
Address:
Via Capitello, 45 - 36066 Sandrigo (VI) - Italy
Declares that the product:
Control box for 1 230/400V AC motor, ideal for industrial sectional doors and heavy duty sliding doors:
THINK - THINK.P - THINK.I
conforms with the requirements of the following EC Directives:
• DIRECTIVE 2004/108/CE OF THE EUROPEAN PARLIAMENT AND COUNCIL, 15 December 2004, in
relation to the harmonisation of the legislation of member states regarding electromagnetic compatibility , in abro-
gation of Directive 89/336/CEE, per the following harmonised standards:
EN 61000-6-2:2005, EN 61000-6-3:2007.
• DIRECTIVE 2006/95/CE OF THE EUROPEAN PARLIAMENT AND COUNCIL, 12 December 2006, in
relation to the harmonisation of the legislation of member states regarding electrical material intended to be used
within certain voltage ranges, per the following harmonised standards:
EN 60335-1:2002 + A1:2004 + A11:2004 + A12:2006 + A2:2006 + A13:2008; EN 60335-1-103:2003.
as applicable:
• DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND COUNCIL, 9 March 1999 in relation to
radio equipment and telecommunications terminals and the mutual recognition of their conformity, per the following
harmonised standards:
ETSI EN 301 489-3 V1.4.1 (2002) + ETSI EN 301 489-1 V1.4.1 (2002) + ETSI EN 300 220-3 V1.1.1 (2000) + EN
60950-1 (2001)
Benincà Luigi, Legal representative.
Sandrigo, 02/11/2010.

11
THINK Control Unit
INPUT/OUTPUT FUNCTIONS
THINK Control Unit
Terminal No. Function Description
1-2-3 Motor
Connection, 230Vac motor - single-phase:
1-Movement+capacitor/2-Common/3-Movement+capacitor
Connection, 400Vac motor - three-phase:
1-U/2-V/3-W
Check that the voltage selection jumper on terminals 36-37-38 is correctly positioned.
4-5 Flashing light Connection of flashing light, 230Vac 40W max.
Connect a negative electric brake to this output.
5-6 AUX WARNING: Output, 230Vac 0,5A max.
7-8 Auxiliary capaci-
tor Output for pickup auxiliary capacitor. See wire diagram.
9-10 Courtesy light Free N.O. contact (2A 150W) to control the Courtesy light which is timed according to the
TLS parameter.
11-12 24Vac Output, accessory power supply 24Vac/0,5A max
13-14 SCA/PhotoTest
Output, 24Vac/0,5A max. This can be preset as open gate indicator light or as checked
devices power supply (PhotoTest) through the TSTP logic.
In the event of presetting as PhotoTest, please refer to the diagram “Connection of checked
safety devices”
15 COM Common for limit switches and photocells
16 SWO Input, OPEN limit switch (N.C. contact)
17 SWC Input, CLOSE limit switch (N.C. contact)
18 PHOT 1 Input, Photocell 1 (N.C. contact). It can be disabled in the opening phase, see PHO1 logic.
19 PHOT 2 Input, Photocell 2 (N.C. contact). It can be disabled in the opening phase, see PHO2 logic.
20 PHOT 3 Input, Photocell 3 (N.C. contact). It can be disabled in the opening phase, see PHO3 logic.
21 PHOT 4 Input, Photocell 4 (N.C. contact). It can be disabled in the opening phase, see PHO4 logic.
22 STOP Input, STOP push-button (N.C. contact)
23 OPEN Input, OPEN push-button (N.O. contact).
24 CLOSE Input, CLOSE push-button (N.O. contact)
25 PED Input, pedestrian push-button (N.O. contact)
26 Step-by-step Input, step-by-step (N.O. contact)
27 COM Common for all other control inputs.
28-29 DAS
Input, safety edge contact.
Resistive edge: closed “ DAS” jumper.
Mechanical edge: open “DAS” jumper.
When the safety edge is activated, the gate movement stops. The gate movement is re-
versed for approximately 3 sec if the INVA logic is ON. If no safety edge is used: “DAS”
Jumper open, jumper between terminals 28-29.
30-31 Aerial
Connection of the antenna to the receiver extractable board (30-signal/31-screen).
32-33 2nd radio channel Output, 2nd radio channel of the two-channel extractable receiver.
34-35 SAFETY
Emergency stop connection. WARNING: Mains power supply.
Remove the jumper and connect a N.C., changeover switch, suited for the mains voltage.
See wire diagram.
36-37-38
Selection of
Mains power
supply
Selection of power supply voltage, short-circuit:
36 and 37 for three-phase power supply (400Vac)
37 and 38 for single-phase power supply (230Vac)
39-40 Single-phase
power supply Input, single-phase mains power supply 230Vac/50Hz (39-L / 40-N)
39-40-41 Three-phase
power supply Input, or three-phase mains power supply, 400Vac/50Hz (39-R / 40-S / 41-T).

12
Programming
The various functions of the control unit can be programmed by using the LCD display provided on the side of the unit and by set-
ting the desired values on the Programming Menu, as described hereunder.
The Parameters Menu allows for the presetting of a digit value to a function, like an adjustment trimmer.
The Logic Menu allows for the activation and deactivation of a function, like the setting of a Dip-Switch.
The special functions follow the Parameters Menu and the Logic Menu and can vary according to the type of control unit or soft-
ware review.
To access programming :
1 – Press the <PG> push-button, the first Parameters Menu “PAR” appears on the display.
2 – Select the desired menu by using the <+> or <-> keys (PAR>>LOG>>NMAN>>RES>>PAR>>....).
3 – Press the <PG> push-button, the display shows the first function available in the Menu.
4 – By using the <+> or <-> keys select the function to be modified.
5 – Press the <PG> push-button, the currently preset value for the selected function is displayed.
6 – By using the <+> or <-> keys, select the value which is to be assigned to the function.
7 – Press the <PG> push-button and the “PRG” message is displayed. This means that programming has been completed.
Note:
The <+> e <-> push-buttons, when the unit is not in programming mode, perform the OPEN and CLOSE function, respectively, in
service man mode (the buttons should be kept pressed for the entire duration of the operation).
When upon a Function Menu, press keys <+> e <-> simultaneously to pass to higher menu without making any change.
When the unit is switched on, the Software version is displayed for around 2sec.
Keep either keys <+> or <-> pressed to speed up the increase/decrease of values.
After 60 sec wait, the control unit exits the Programming mode and the display switches off.
Parameters, Logic and Special Functions
In the tables hereunder the single functions available in the control unit are shown.
MENU FUNCTION Settable values
MIN-MAX-(Default) MEMO
PARAMETERS
TCA
Automatic closure time. Active with logic “TCA”= ON only.
At the end of the preset time, the control unit sends a closure control
signal.
1-240-(40s)
TM Motor operating time. The operation time is adjusted during the opening
and closing phases of the motor. 5-180-(40s)
Tped The stroke time of the gate leaf is adjusted during the partial opening
phase (pedestrian mode). 5-180-(10s)
SnSo
* The amperometric sensor sensitivity is adjusted in the opening phase.
This is operating only with logic AMP:ON.
1:maximum sensitivity - 99:minimum sensitivity.
The sensor triggering in the opening phase stops the movement immedi-
ately.
1-99-(20%)
SnSC
* The amperometric sensor sensitivity is adjusted in the closing phase.
This is operating only with logic AMP:ON.
1: maximum sensitivity - 99:minimum sensitivity.
When the sensors triggers in the closing phase, the gate stops immedi-
ately and a reversion movement (opening) starts for approximately 3 sec.
1-99-(20%)
TLS
The activation time of the courtesy light is adjusted. The contact closes
with the beginning of the opening operation. The time counting starts only
with gate completely closed.
1-240-(1s)
SaFM
This is operating only with logic SMOT:ON. The motor protection switch
triggering is adjusted. The value is expressed in Amperes.
1: triggering of protection switch at 1 Ampere of consumption
14: protection disabled.
1-14-(6A)
* WARNING:
An incorrect setting of these parameters may cause danger. Please comply with regulations in force!

13
MENU FUNCTION Settable values
ON-OFF-(Default) MEMO
LOGIC
TCA
The automatic closure is enabled or disabled.
Off: disabled automatic closure.
On: enabled automatic closure.
(ON)
IbL
The multi-flat function is enabled or disabled.
Off: disabled multi-flat function.
On: enabled multi-flat function. The P.P. (Step-by-step) impulse or the
impulse of the transmitter has no effect in the opening phase.
(OFF)
SCL
The rapid closure is enabled or disabled.
On: enabled rapid closure. With open gate or gate in the opening phase, the
activation of the photocell causes the automatic closure of the gate 3 sec
after its activation. This function is enabled only with TCA:ON
Off: rapid closure disabled.
(OFF)
PP
The operating mode The operating mode of the “P.P.” (Step-by Step) button
and of the transmitter is selected.
Off: Operation: OPEN > STOP > CLOSE > STOP >
On: Operation : OPEN > CLOSE > OPEN >
(OFF)
PRE
Forewarning flashing light enabled or disabled.
Off: disabled forewarning flashing light.
On: enabled forewarning flashing light. The flashing light is activated 3 sec
before the motor starts.
(OFF)
CLOC
The OPEN input mode is selected.
Off: OPEN input, with OPEN function.
On: OPEN input, with CLOCK function.
To be used for connection to timer for timed opening/closing. (CLOSED con-
tact: open gate. OPEN contact: normal operation).
(OFF)
htr
The Service Man function is enabled or disabled.
Off: Automatic operation.
On: Service Man operation.
The OPEN/CLOSE push-buttons should be kept pressed for the entire oper-
ating time.
(OFF)
BLC
The lock function is enabled or disabled.
Off: Lock function disabled.
On: Lock function enabled. After the triggering of the closure limit switches,
the control unit delays the stop by approx. 0.5sec in order to allow a better
resting of the gate leaf onto the stoppers. DAS input is activated in the clos-
ing phase only.
Note: In case of sliding gates, leave to OFF.
(OFF)
Pho1
Photocell 1 input in the opening phase is enabled or disabled.
On: Photocell 1 is activated in the closing phase only.
Off: Photocell 1 is activated in both opening and closing phases.
(OFF)
Pho2
Photocell 2 input in the opening phase is enabled or disabled.
On: Photocell 2 is activated in the closing phase only.
Off: Photocell 2 is activated in both opening and closing phases.
(OFF)
Pho3
Photocell 3 input in the opening phase is enabled or disabled.
On: Photocell 3 is activated in the closing phase only.
Off: Photocell 3 is activated in both opening and closing phases.
(OFF)
Pho4
Photocell 4 input in the opening phase is enabled or disabled.
On: Photocell 4 is activated in the closing phase only.
Off: Photocell 4 is activated in both opening and closing phases.
(OFF)
TSTP
The operating mode of output SCA/TESTPHOT is selected.
On: Photocell power supply in Test mode as per diagram at page 4. Before
each operation all PHOT inputs are checked. If the result is negative, the
operation will not take place.
Off: Output preset as open gate warning LED.
(OFF)
Faut
The check function of single failure is enabled or disabled.
Off: Single failure check is disabled.
On: Single failure check enabled in compliance with the Machinery Directive
98/37/CE.
(OFF)
AMP
The anti-crash amperometric sensor is disabled or enabled. Its sensitivity is
adjusted by parameters SNSO and SNSC.
On: Amperometric sensor activated.
Off: Amperometric sensor deactivated.
(OFF)

14
MENU FUNCTION Settable values
ON-OFF-(Default) MEMO
LOGIC
2pha
Lack of phase check in case of three-phase power supply is enabled or
disabled.
On: Check activated.
Off: Check deactivated.
(OFF)
inva
The movement reversion in the event of triggering of the amperometric
sensor or the DAS input is activated or deactivared.
On: Reversion activated. The activation of the edge or the sensor causes
a movement reversion (opening) for approx. 3 sec.
Off: Movement reversion not activated. The activation of the edge or the
sensor causes the immediate stopping of the gate movement.
(OFF)
Smot
The motor protection switch is enabled or disabled. Its sensitivity is ad-
justed by SAFM parameter.
On: amperometric sensor activated.
Off: amperometric sensor deactivated.
(OFF)
doSp
The rapid movement reversion is enabled or disabled after the activation
of the photocell in the closing phase.
ON: Rapid reversion activated. The movement reversion time, in the event
of activation of the photocell, is reduced to approx. 1 sec.
To be used only on light-weight and fast doors.
OFF: Rapid reversion deactivated. The movement reversion time, in the
event of activation of the photocell, is approx. 3 sec.
(OFF)
MENU FUNCTION
NMAN
The number of the cycles (open+close) completed by the system is displayed.
When the push-button <PG> is pressed once, the first 4 digits are displayed, if the push-button is pressed
once more, the last 4 digits are displayed.
E.g. <PG> 0012 >>> <PG> 3456: 123.456 cycles were performed.
RES
RESET of the control unit. WARNING!: This resets the control unit to the default values.
When the <PG> push-button is pressed once, the RES wording begins to flash, if the push-button <PG> is
pressed once more, the control unit is reset.
IMPORTANT: Photocell inputs not in use
All photocell inputs are short-circuited by default (PHOT1/2/3/4) with the COM terminal. With this presetting, the control unit can
be operated also without photocells.
After connecting and setting the photocells required by the type of system, the inputs which are not in use should be short-circuited
to the inputs in use by copying the settings in the PHOx parameter, as shown hereunder:
1 pair of photocells on input PHOT1, active in the closing phase only:
Logic PHO 1 Logic PHO 2 Logic PHO 3 Logic PHO 4 JUMPERS
ON ON ON ON
18 2019 21
(1) (3)(2) (4)
RX1
1 pair of photocells on input PHOT1, active in both opening and closing:
Logic PHO 1 Logic PHO 2 Logic PHO 3 Logic PHO 4 JUMPERS
OFF OFF OFF OFF
18 2019 21
(1) (3)(2) (4)
RX1
1 pair of photocells: active in both opening and closing (PHOT1)
+ 1 pair of photocells: active in the closing phase only (PHOT2):
Logic PHO 1 Logic PHO 2 Logic PHO 3 Logic PHO 4 JUMPERS
OFF ON ON ON
18 2019 21
(1) (3)(2) (4)
RX1
RX2

15
2 pairs of photocells, active in both opening and closing (PHOT1 e PHOT2)
+ 1 pair of photocells, active in the closing phase only (PHOT3):
Logic PHO 1 Logic PHO 2 Logic PHO 3 Logic PHO 4 JUMPERS
OFF OFF ON ON
18 2019 21
(1) (3)(2) (4)
RX1
RX2
RX3
2 pairs of photocells, active only in the closing phase (PHOT1 e PHOT2)
+ 1 pair of photocells, active in both opening and closing phases (PHOT3):
Logic PHO 1 Logic PHO 2 Logic PHO 3 Logic PHO 4 JUMPERS
ON ON OFF OFF
18 2019 21
(1) (3)(2) (4)
RX1
RX2
RX3
Diagnostics
PHOT1
SWC
STOP
SWO
PHOT3
PHOT4
PHOT2 DAS
P.P. PED OPEN CLOSE
Each input is matched to one segment of the display; in the event of activation, it switches
on according to the following diagram.
The Normally Closed (N.C.) inputs are represented by vertical segments. The Normally
Open (N.O.) inputs are represented by horizontal segments.
Error messages
The control unit checks the correct operation of the safety devices.
In the event of faults the following messages can be displayed:
ERR1 Error, check photocells. Check connections and the correct operation of photocells.
ERR2 Activation of the anti-crash amperometric sensor. Check the presence of any obstacles.
ERR3 Check of single failure has negative result. Contact the technical assistance.
ERR4 Triggering of the motor protection switch. Check the value of the parameter SAFM and check the motor consumption.
ERR5 Lack of one of the three phases. Check the correct connection of power supply of the three-phase mains.
Fuses
F1 Protection fuse, accessories
F2 Protection fuse, logic board
F3 Protection fuse, flashing light and electric brake.s
F4 Primary protection fuse of the transformer.
TECHNICAL DATA
Power supply 230 Vac 50/60 Hz
Output supply 1 motor 230Vac single-phase / 400Vac three-phase
Power maximum motor 230Vac single-phase: 800 W
400Vac three-phase: 2200 W
Output supply accessories
24Vdc 500mA max.
Protection level
IP54
Operating temp.
-20°C / +50°C
Radio receiver
Removable connector for radio receiver

1SFNFSFMFBMFUUFTVJmBODIJQFSTHBODJBSFMFEVFNBTDIFSFDPQSJWJUJ3JNVPWFSFMFEVFWJUJTVMMBUPEJBQFSUVSBEFTJEFSBUP"MMFOUBSFMFEVFWJUJDPOGVO[JPOFEJDFSOJFSBTFO[BSJNVPWFSMFJONPEPEBDPOTFOUJSFMBQFSUVSBEFMDPQFSDIJP1SFTTUIFUBCTPOUIFTJEFTUPSFMFBTFUIFUXPNBTLTUIBUDPWFSUIFTDSFXT3FNPWFUIFUXPTDSFXTPOUIFEFTJSFEPQFOJOHTJEF4MBDLFOUIFUXPTDSFXTUIBUBDUBTBIJOHFXJUIPVUSFNPWJOHUIFNTPBTUPBMMPXPQFOJOHPGUIFDPWFS"VGEJFTFJUMJDIFO-BTDIFOESàDLFOTPEBTTEJFCFJEFO4DISBVCFOCMFOEFOCFGSFJUXFSEFO%JFCFJEFO4DISBVCFOBOEFSHFXàOTDIUFO½GGOVOHTTFJUFBVTCBVFO;VMFU[UEJFCFJEFOBMT4DIBSOJFSEJFOFOEFO4DISBVCFOMPDLFSOBCFSOJDIUBVTCBVFOEBNJUEFS%FDLFMHFÚGGOFUXFSEFOLBOO1SFTTFSMFTEFVYBJMFUUFTMBUÏSBMFTQPVSEÏDSPDIFSMFTEFVYDBDIFWJT&OMFWFSMFTEFVYWJTTVSMFDÙUÏEPVWFSUVSFEÏTJSÏ%FTTFSSFSMFTEFVYWJTGBJTBOUGPODUJPOEFDIBSOJÒSFTBOTMFTFOMFWFSEFNBOJÒSFËQFSNFUUSFMPVWFSUVSFEVDPVWFSDMF1SFTJPOBSMBTBMFUBTFOMPTMBEPTQBSBEFTFOHBODIBSMBTEPTUBQBTDVCSFUPSOJMMPT&YUSBFSMPTEPTUPSOJMMPTEFMMBEPEFBQFSUVSBEFTFBEP"nPKBSMPTEPTUPSOJMMPTDPOGVODJØOEFCJTBHSBTJOFYUSBFSMPTBmOEFQPEFSBCSJSMBUBQB
/BDJTOįİCPD[OFLMBQLJXDFMVPEIBD[FOJBEXØDINBTFLOBLSZXBKįDZDIŔSVCZ
8ZDJįHOįİEXJFŔSVCZQPXZCSBOFKEPPUXJFSBOJBTUSPOJF1PMV[PXBİEXJFŔSVCZCMPLVKįDFCF[XZDJįHBOJBJDIXTQPTØCVNPŤMJXJBKįDZPUXBSDJFOBLSZXLJ"650."5*4.*#&/*/$®4Q"7JB$BQJUFMMP4BOESJHP7*5FMSB'BY
1SFNFSFMFBMFUUFTVJmBODIJQFSTHBODJBSFMFEVFNBTDIFSFDPQSJWJUJ3JNVPWFSFMFEVFWJUJTVMMBUPEJBQFSUVSBEFTJEFSBUP"MMFOUBSFMFEVFWJUJDPOGVO[JPOFEJDFSOJFSBTFO[BSJNVPWFSMFJONPEPEBDPOTFOUJSFMBQFSUVSBEFMDPQFSDIJP1SFTTUIFUBCTPOUIFTJEFTUPSFMFBTFUIFUXPNBTLTUIBUDPWFSUIFTDSFXT3FNPWFUIFUXPTDSFXTPOUIFEFTJSFEPQFOJOHTJEF4MBDLFOUIFUXPTDSFXTUIBUBDUBTBIJOHFXJUIPVUSFNPWJOHUIFNTPBTUPBMMPXPQFOJOHPGUIFDPWFS"VGEJFTFJUMJDIFO-BTDIFOESàDLFOTPEBTTEJFCFJEFO4DISBVCFOCMFOEFOCFGSFJUXFSEFO%JFCFJEFO4DISBVCFOBOEFSHFXàOTDIUFO½GGOVOHTTFJUFBVTCBVFO;VMFU[UEJFCFJEFOBMT4DIBSOJFSEJFOFOEFO4DISBVCFOMPDLFSOBCFSOJDIUBVTCBVFOEBNJUEFS%FDLFMHFÚGGOFUXFSEFOLBOO1SFTTFSMFTEFVYBJMFUUFTMBUÏSBMFTQPVSEÏDSPDIFSMFTEFVYDBDIFWJT&OMFWFSMFTEFVYWJTTVSMFDÙUÏEPVWFSUVSFEÏTJSÏ%FTTFSSFSMFTEFVYWJTGBJTBOUGPODUJPOEFDIBSOJÒSFTBOTMFTFOMFWFSEFNBOJÒSFËQFSNFUUSFMPVWFSUVSFEVDPVWFSDMF1SFTJPOBSMBTBMFUBTFOMPTMBEPTQBSBEFTFOHBODIBSMBTEPTUBQBTDVCSFUPSOJMMPT&YUSBFSMPTEPTUPSOJMMPTEFMMBEPEFBQFSUVSBEFTFBEP"nPKBSMPTEPTUPSOJMMPTDPOGVODJØOEFCJTBHSBTJOFYUSBFSMPTBmOEFQPEFSBCSJSMBUBQB
/BDJTOįİCPD[OFLMBQLJXDFMVPEIBD[FOJBEXØDINBTFLOBLSZXBKįDZDIŔSVCZ
8ZDJįHOįİEXJFŔSVCZQPXZCSBOFKEPPUXJFSBOJBTUSPOJF1PMV[PXBİEXJFŔSVCZCMPLVKįDFCF[XZDJįHBOJBJDIXTQPTØCVNPŤMJXJBKįDZPUXBSDJFOBLSZXLJ
"650."5*4.*#&/*/$®4Q"7JB$BQJUFMMP4BOESJHP7*5FMSB'BY
1SFNFSFMFBMFUUFTVJmBODIJQFSTHBODJBSFMFEVFNBTDIFSFDPQSJWJUJ3JNVPWFSFMFEVFWJUJTVMMBUPEJBQFSUVSBEFTJEFSBUP"MMFOUBSFMFEVFWJUJDPOGVO[JPOFEJDFSOJFSBTFO[BSJNVPWFSMFJONPEPEBDPOTFOUJSFMBQFSUVSBEFMDPQFSDIJP1SFTTUIFUBCTPOUIFTJEFTUPSFMFBTFUIFUXPNBTLTUIBUDPWFSUIFTDSFXT3FNPWFUIFUXPTDSFXTPOUIFEFTJSFEPQFOJOHTJEF4MBDLFOUIFUXPTDSFXTUIBUBDUBTBIJOHFXJUIPVUSFNPWJOHUIFNTPBTUPBMMPXPQFOJOHPGUIFDPWFS"VGEJFTFJUMJDIFO-BTDIFOESàDLFOTPEBTTEJFCFJEFO4DISBVCFOCMFOEFOCFGSFJUXFSEFO%JFCFJEFO4DISBVCFOBOEFSHFXàOTDIUFO½GGOVOHTTFJUFBVTCBVFO;VMFU[UEJFCFJEFOBMT4DIBSOJFSEJFOFOEFO4DISBVCFOMPDLFSOBCFSOJDIUBVTCBVFOEBNJUEFS%FDLFMHFÚGGOFUXFSEFOLBOO1SFTTFSMFTEFVYBJMFUUFTMBUÏSBMFTQPVSEÏDSPDIFSMFTEFVYDBDIFWJT&OMFWFSMFTEFVYWJTTVSMFDÙUÏEPVWFSUVSFEÏTJSÏ%FTTFSSFSMFTEFVYWJTGBJTBOUGPODUJPOEFDIBSOJÒSFTBOTMFTFOMFWFSEFNBOJÒSFËQFSNFUUSFMPVWFSUVSFEVDPVWFSDMF1SFTJPOBSMBTBMFUBTFOMPTMBEPTQBSBEFTFOHBODIBSMBTEPTUBQBTDVCSFUPSOJMMPT&YUSBFSMPTEPTUPSOJMMPTEFMMBEPEFBQFSUVSBEFTFBEP"nPKBSMPTEPTUPSOJMMPTDPOGVODJØOEFCJTBHSBTJOFYUSBFSMPTBmOEFQPEFSBCSJSMBUBQB
/BDJTOįİCPD[OFLMBQLJXDFMVPEIBD[FOJBEXØDINBTFLOBLSZXBKįDZDIŔSVCZ
8ZDJįHOįİEXJFŔSVCZQPXZCSBOFKEPPUXJFSBOJBTUSPOJF1PMV[PXBİEXJFŔSVCZCMPLVKįDFCF[XZDJįHBOJBJDIXTQPTØCVNPŤMJXJBKįDZPUXBSDJFOBLSZXLJ"650."5*4.*#&/*/$®4Q"7JB$BQJUFMMP4BOESJHP7*5FMSB'BY