Gira One 5065 00 User manual

Operating instructions
82404412 / 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang
Order no. 5065 00

Dimming actuator 1-gang 200 W with binary input, 3-gang
Table of Contents
1 Safety instructions.............................................................................................................3
2 Device components...........................................................................................................4
3 Function ............................................................................................................................5
4 Information for electrically skilled persons ........................................................................7
4.1 Mounting and electrical connection........................................................................ 7
4.2 Commissioning ...................................................................................................... 9
5 Technical data.................................................................................................................10
6 Troubleshooting ..............................................................................................................12
7 Accessories.....................................................................................................................14
8 Parameter list ..................................................................................................................15
9 Warranty..........................................................................................................................19
2 / 19
82404412 02.12.2022

1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled
persons.
Serious injuries, fire or property damage possible. Please read and follow manual
fully.
Danger of electric shock. Device is not suitable for disconnection from supply voltage
because mains potential even is applied on the load when the output is switched off.
Always disconnect before carrying out work on the device or load. To do so, switch
off all associated circuit breakers.
Danger of electric shock. Make sure during the installation that there is always suffi-
cient insulation between the mains voltage and the bus. A minimum distance of at
least 4 mm must be maintained between bus conductors and mains voltage cores.
Danger of electric shock on the installation. Do not connect any external voltage to
the inputs. The device might be damaged, and the SELV potential on the bus line will
no longer be available.
Fire hazard. For operation with inductive transformers, each transformer must be
fused on the primary side in accordance with the manufacturer's instructions. Only
safety transformers according to EN 61558-2-6 may be used.
Risk of destruction of the dimmer and load if the set operating mode and load type do
not match. Set the correct dimming principle before connecting or exchanging the
load.
This manual is an integral part of the product, and must remain with the end cus-
tomer.
3 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

2 Device components
Image1: Device components
(1) Programming LED
(2) Programming button
(3) Control cable (bus connection and extension inputs)
(4) Load connection (dimming output)
Image2: Connection assignment of control cable (example)
red (RD) KNX / One +
black (BK) KNX / One -
green (GN) Input 1 (push-button, switch, contact, condensation/leakage sensor)
yellow (YE) Input 2 (push-button, switch, contact, condensation/leakage sensor)
white (WH) Input 3 (push-button, switch, contact, condensation/leakage sensor,
NTC temperature sensor)
brown (BN) COM inputs 1...3
4 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

3 Function
System information
This device is a product for the Gira One Smart Home system. The Gira One system
is commissioned easily and in a time-saving manner using the Gira Project Assistant.
The Gira One Smart Home system enables the control and automation of lighting,
heating and shading, as well as connection to various third-party systems and much
more. It can be operated via Gira One switches, by app from home or securely from a
remote location. Electrically skilled persons can maintain the Gira One project re-
motely free of charge.
Data transmission between the Gira One devices is encrypted. This provides protec-
tion against third-party access and manipulation.
Commissioning is carried out with the free Gira Project Assistant (GPA), version 5 or
higher. Free function and security updates are also transferred to the Gira One
devices with the GPA.
The Gira One system is based on the globally proven KNX smart home standard.
Intended use
– Operation in Gira One system
– Switching and dimming of lighting
– Reading in switching states of installation switches or push-buttons and other
potential-free contacts at inputs 1...3
– Signal evaluation of condensation and leakage sensors at inputs 1...3 (see ac-
cessory).
– Acquisition of temperature values via NTC temperature sensor at input 3 (see
accessories)
– Mounting in appliance box with dimensions according to DIN 49073
Product characteristics
– Output can be operated via the Gira One system or extension inputs
– Three extension inputs for connecting potential-free contacts or dew/leakage
sensors. NTC temperature sensor can be connected to input 3.
– Supply via the bus, no additional supply voltage necessary
– Actuator for switching and dimming of incandescent lamps, HV halogen lamps,
dimmable HV LED lamps, dimmable compact fluorescent lamps, dimmable in-
ductive transformers with LV halogen or LV LED lamps, dimmable electronic
transformers with LV halogen or LV LED lamps.
– Automatic or manual selection of the dimming principle suitable for the load.
– Protected against no-load, short-circuit and overheating.
– Power extension by means of power packs.
5 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

– Programming and commissioning with the Gira Project Assistant (GPA), ver-
sion 5 or higher.
– Updating via the Gira Project Assistant (GPA).
– Encrypted data transmission between the Gira One devices.
Dimming operation characteristics
– Minimum and maximum brightness can be set.
– Switching on to last brightness value or to permanently set switch-on bright-
ness.
– Setting of a switch-on or switch-off delay.
– Staircase function for which a pre-warning time and a pre-warning brightness
can optionally be set.
Flickering of the connected lamps due to undershoot of the specified minimum
load or through centralised pulses from the power stations. This does not rep-
resent any defect in the device.
Extension input characteristics
– Single or dual-area operation can be configured for rockers.
– Connection of rockers that are configured with the function for switching, dim-
ming, shading and ventilation, scene recall, staircase (motion detector), floor
call, garage door and door opener.
– Connection of motion and presence detectors with potential-free relay outputs.
– Convenient group control of switching, dimming, shading and ventilation loads.
– Switching contact evaluation of wind, frost, brightness or rain sensors with po-
tential-free relay outputs possible in order to protect shading and ventilation
loads against environmental influences.
– Window contact polling and visualisation in the Smart Home app: An open
window leads to the frost protection heating mode after a configured time has
elapsed.
– Door contact polling and visualisation in the Smart Home app: An open door
leads to the Venetian blind or shutters being raised and locked.
– Polling of a switch-over between heating/cooling at a heat pump in order to be
able to forward the current operating mode (heating or cooling) to a heating
controller.
– Switching contact indicator for displaying a contact state in the Smart Home
app.
– Configurable switching inputs that can be parameterised independently.
– Acquisition and calibration of temperature values via remote sensors (see ac-
cessories) at input 3.
6 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

4 Information for electrically skilled persons
DANGER!
Mortal danger of electric shock.
Disconnect the device. Cover up live parts.
4.1 Mounting and electrical connection
DANGER!
When connecting the bus/extensions and mains voltage wires in a shared appliance
box, the bus line may come into contact with the mains voltage.
This endangers the safety of the entire installation. People at remote devices may
also receive an electric shock.
Do not place bus/extensions and mains voltage terminals in a shared connection
compartment. Use an appliance box with a fixed partition wall or separate appliance
boxes.
Connecting and fitting the device
– Enter or scan the device certificate and add it to the project. A high resolution
camera should be used to scan the QR code.
– The device certificate should be removed from the device during mounting.
– Document all passwords and keep them safe.
Mounting in suitable appliance box (recommendation: electronic device box with par-
tition). Observe cable routing and spacing (see figure 3)!
7 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

Image3: Mounting example in electronic appliance box with partition wall, series
push-button and NTC temperature sensor
(5) Appliance box
(6) Partition
(7) potential-free contacts (e.g. series push-button)
(8) NTC temperature sensor (optional)
Image4: Cable spacing
Minimum spacing between the mains voltage and bus/extension wires: 4 mm
(see figure 4)
Image5: Connection of load
8 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

Observe ambient temperature. Ensure adequate cooling.
￭ Connect bus line, observing the correct polarity.
￭ Connect load as shown in the connection example (see figure 5).
￭ If required, connect potential-free contacts or condensation/leakage sensors to
inputs 1...3, or NTC temperature sensors to input 3 (see figure 2).
￭ Install the device in the appliance box.
The COM reference potential must not be connected together with COM con-
nections of other devices!
4.2 Commissioning
Commissioning the device
Delivery state: The output is set to the universal dimming principle with automatic re-
cognition of the load type. Operation of the output is possible via input 1 (ON/
Brighter) and input 2 (OFF/Darker). Input 3 has no function.
Function of Inputs in the as-delivered state
Input Push-button (NO con-
tact)
Function
1 Press briefly (< 0.4 s) Switch on
1 Press for a long time (>
0.4 s)
Increase brightness
2 Press briefly (< 0.4 s) Switch off
2 Press for a long time (>
0.4 s)
Reduce brightness
3 --- ---
The device is commissioned with the Gira Project Assistant (GPA) version 5 or
higher.
Safe-state mode
The safe-state mode stops the execution of the program.
Only the system software of the device is still functional. Diagnosis functions and pro-
gramming of the device are possible.
Activating safe-state mode
￭ Switch off the bus voltage or disconnect the device from the bus.
￭ Wait about 10 s.
￭ Press and hold down the programming button.
￭ Switch on the bus voltage or connect the bus again at the device. Release the
programming button only after the programming LED starts flashing slowly.
The safe-state mode is activated.
9 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

Deactivating safe-state mode
￭ Switch off the bus voltage (wait approx. 10 s) or carry out programming.
Master reset
The master reset restores the basic device settings (firmware remains in place). The
device must then be recommissioned with the GPA.
Performing a master reset
Precondition: The safe-state mode is activated.
￭ Press and hold down the programming button for > 5 s.
The programming LED flashes quickly.
The device performs a master reset, restarts and is ready for operation again
after approx. 5 s.
5 Technical data
Rated voltage DC 21 ... 32 V SELV
Current consumption 5 ... 18 mA
Connection mode Device connection terminal on control
cable
Output
Rated voltage AC 230 V ~
Mains frequency 50 / 60 Hz
Power loss max. 1.5 W
Standby power approx. 0.2 W
Connection mode Screw terminals
Connected loads see tables: (see figure 6) and (see figure 7)
Load types
UNI universal (with automatic calibration procedure)
LJconv. transformer (inductive / leading edge phase control)
|LED (leading edge phase control)
dželectr. transformer (capacitive / trailing edge phase control)
{LED (trailing edge phase control)
10 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

Image6: Connected load LED lamps
Image7: Connected load conventional lamps
Power reduction
when installed in wooden or dry construction walls -15%
when installed in multiple combinations -20%
Clampable conductor cross-section
Single stranded 0.5 ... 4 mm²
Finely stranded without conductor sleeve 0.5 ... 4 mm²
Finely stranded with conductor sleeve 0.5 ... 2.5 mm²
Connection torque, screw terminals max. 0.8 Nm
11 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

Ambient conditions
Ambient temperature -5 ... +45 °C
Storage/transport temperature -25 ... +70 °C
Dimensions (W × H × D) 48 x 50 x 28 mm
Inputs
Control cable (preterminated) YY6x0.6
Input type Potential-free
Number 3
Total length of extension device cable max. 10 m
Cable type (preferably) J-Y(St)Y
Poll voltage, extension inputs approx. 5 V
6 Troubleshooting
Connected LED lamps or compact fluorescent lamps switch off in the lowest dimming
position or flicker
The set minimum brightness is too low.
Increase minimum brightness.
Connected LED lamps or compact fluorescent lamps flicker
Cause 1: Lamps are not dimmable.
Check manufacturer's instructions.
Exchange lamps for another type.
Cause 2: Dimming principle and lamps do not optimally match.
For HV-LED: Check operation in another dimming principle, reduce connected
load as well if necessary.
For LV-LED: Check the lamp operating device and replace as necessary.
With the "Universal" setting: Define the dimming principle manually.
Connected HV-LED lamps or compact fluorescent lamps in the lowest dimming
position are too bright; dimming range is too small
Cause 1: The set minimum brightness is too high.
– Reduce minimum brightness.
Cause 2: LED dimming principle (trailing edge phase control) does not optimally
match the connected lamps.
– Check operation in the "LED leading edge phase control" setting, reduce con-
nected load as well if necessary.
– Exchange lamps for another type.
12 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

Output has switched off.
Cause 1: Overheating protection has tripped.
– Disconnect output from mains, switch off associated circuit breakers.
– LED (trailing edge phase control): Reduce the connected load. Exchange
lamps for another type.
– LED (leading edge phase control): Reduce the connected load. Check opera-
tion in the setting "LED trailing edge phase control". Exchange lamps for an-
other type.
– Let device cool down for at least 15 minutes. Check installation situation, en-
sure cooling, e.g. provide distance from surrounding devices.
Cause 2: Overvoltage protection has tripped.
– LED (trailing edge phase control): Check operation in the setting "LED leading
edge phase control", reduce connected load as well if necessary.
– Exchange lamps for another type.
Cause 3: short-circuit in output circuit
– Disconnect the output from the mains supply.
– Eliminate short-circuit.
– Switch on mains voltage again. Switch the affected output off and on again.
When a short-circuit occurs the affected output switches off. Automatic restart when
short-circuit is eliminated within 100 ms (inductive load) or 7 seconds (capacitive or
ohmic load). After that lasting switch-off.
When a short-circuit occurs during the calibration process, the load calibrates itself
again after the short-circuit is eliminated.
Cause 4: load failure.
– Check load, replace lamp. For inductive transformers, check primary fuse and
replace if necessary.
Output off and not possible to switch on
Cause: bus voltage failure.
Check bus voltage.
Luminaires flicker or buzz, proper dimming not possible, device buzzes
Cause: wrong dimming principle set.
Installation or commissioning error. Disconnect device and luminaire, switch off
circuit breaker.
Check installation and correct.
If the wrong dimming principle has been preselected: Set correct dimming prin-
ciple.
If dimming actuator calibrates itself incorrectly, e.g. with highly inductive mains
or long load cables: preselect correct dimming principle with commissioning.
13 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

LED lamp is dimly lit when dimmer is switched off
Cause: LED lamp is not optimally suited for this dimmer.
Use a compensation module, see accessories.
Use another type of LED lamp or an LED lamp of another manufacturer.
7 Accessories
Remote sensor (NTC temperature sensor) 1493 00
Condensation sensor 5069 00
Leakage sensor 5068 00
14 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

8 Parameter list
Parameters that can be set via the GPA:
Output
Load type universal (with automatic calibration pro-
cedure)
electr. transformer (capacitive / trailing
edge phase control)
conv. transformer (inductive / leading
edge phase control)
LED (trailing edge phase control)
LED (leading edge phase control)
The dimming principle of the dimming channel is specified here.
universal (with automatic calibration procedure):
The dimming channel automatically sets the connected load type. After program-
ming, after bus voltage return (without mains voltage) or after switching on the mains
voltage supply of a load output, the actuator calibrates itself automatically to the con-
nected load. The calibration procedure becomes noticeable during ohmic loads by a
brief flicker and lasts up to 10 seconds depending on the network conditions.
electr. transformer (capacitive / trailing edge phase control):
The dimming channel is set to the trailing edge phase control principle. Ohmic loads
or electronic transformers can be connected to the output.
conv. transformer (inductive / leading edge phase control):
The dimming channel is set to the leading edge phase control principle. Conven-
tional transformers can be connected to the output.
LED (trailing edge phase control):
The dimming channel is set to an optimised trailing edge phase control principle. HV
LED or compact fluorescent lamps optimised for this dimming principle can be con-
nected to the output.
LED (leading edge phase control):
The dimming channel is set to an optimised leading edge phase control principle. HV
LED or compact fluorescent lamps optimised for this dimming principle can be con-
nected to the output.
15 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

Minimum brightness Level 1 (darker)
Level 2
...
Level 7
Level 8 (brighter)
The step value set here is a gauge for the minimum adjustable residual phase angle
of the output signal.
The value set here cannot be undershot in any switched-on operating state of the
dimming channel, i.e. under no circumstances can the light be dimmed darker than
the value set here.
Switch-on brightness Fixed switch-on brightness
Last brightness value
Here you can specify the brightness value with which the lamp is to be switched on
by pressing the button briefly:
Fixed switch-on brightness
In this case, you can select a fixed value (1 - 100%) in the "Switch-on brightness
value" field that opens.
Last brightness value
The lamp is switched on with the brightness value that was active and saved intern-
ally before it was last switched off.
Switch-on brightness value 1
5
...
100
Here you can specify the switch-on brightness.
This parameter is only available if the setting "Fixed switch-on brightness" has been
selected for the parameter "Switch-on brightness".
Maximum brightness value 1
5
...
100
The value set here cannot be overshot in any switched-on operating state of the
dimming channel, i.e. under no circumstances can the light be dimmed brighter than
the value set here.
16 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

Switch-on delay 0 ... 3599 s (0 ... 59:59 min)
This parameter is used for setting the duration of the switch-on delay.
After receipt of an ON-telegram, the time that can be configured here is started. The
lamp is switched on after the set time has elapsed.
A further ON-telegram during the switch-on delay time re-triggers the time, i.e. the
time set here is started again.
An OFF-telegram received during the ON-delay will end the delay and sets the
switching status to "OFF".
Switch-off delay 0 ... 3599 s (0 ... 59:59 min)
This parameter is used for setting the duration of the switch-off delay.
After receipt of an OFF-telegram, the time that can be configured here is started.
The lamp is switched off after the set time has elapsed.
A further OFF-telegram during the switch-off delay time re-triggers the time, i.e. the
time set here is started again.
An ON-telegram received during the OFF-delay will end the delay and sets the
switching status to "ON".
Staircase switch switch-off delay 0 ... 65535 s (0 ... 18:12:15 h)
The duration of the switch-on time for the staircase function is configured here.
Once the time set here has elapsed, the lighting is switched off or (if configured) the
pre-warning time is started.
The staircase function is only active if the function "Staircase" has been selected for
the push-button of this dimming channel.
Pre-warning time 0 ... 3599 s (0 ... 59:59 min)
In accordance with DIN 18015-2, the pre-warning is intended to warn persons still on
the staircase that the light will soon be switched off automatically.
The pre-warning time set here is added to the time set in the parameter "Staircase
switch switch-off delay".
As a pre-warning, a pre-warning brightness that is to apply before the channel
switches off permanently can be set using the parameter "Dimming brightness
value". The pre-warning brightness is normally reduced in the brightness value com-
pared to the switch-on brightness.
17 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

Dimming brightness value 1
5
...
100
Here you can set the brightness value that is to apply during the pre-warning time.
During the pre-warning time, the dimming channel is set to the configured brightness
value.
This parameter is only available if a time has been entered for the parameter "Pre-
warning time".
Input
Debounce time 10 ... 255 ms
This parameter sets the debouncing time individually for the input.
According to the time set here, the input signal at the input is evaluated with a delay.
Contact type NO contact
NC contact
The contact type of the connected contact is defined here.
When closing the contact No reaction
Switch on
Switch off
Toggle
This parameter determines the reaction when the contact connected to the input is
closed.
When opening the contact No reaction
Switch on
Switch off
Toggle
This parameter determines the reaction when the contact connected to the input is
opened.
18 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang

Temperature calibration - 12.8 ... 12.7 K
The value for the temperature calibration can be entered here if the temperature
measured by the connected sensor differs from the actual room temperature.
To determine the temperature deviation, the actual room temperature should be de-
tected with a reference measurement using a calibrated temperature measuring
device.
The measured value must be raised if the value measured by the sensor is below
the actual temperature. The measured value must be lowered if the value measured
by the sensor is above the actual temperature.
9 Warranty
The warranty is provided in accordance with statutory requirements via the specialist
trade. Please submit or send faulty devices postage paid together with an error de-
scription to your responsible salesperson (specialist trade/installation company/elec-
trical specialist trade). They will forward the devices to the Gira Service Center.
Gira
Giersiepen GmbH & Co. KG
Elektro-Installations-
Systeme
Industriegebiet Mermbach
Dahlienstraße
42477 Radevormwald
Postfach 12 20
42461 Radevormwald
Deutschland
Tel [phone] - 602-0
Fax [phone] - 602-191
www.gira.de
[email protected]
19 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang