Gira KNX 1039 00 User manual

Operating instructions
32560272 / 108707200 / 27.04.2023
Blind actuator 4-gang 230 V AC
Order no. 1039 00
Blind actuator 2-gang 230 V AC
Order no. 2152 00
Blind actuator 4-gang 24 V DC
Order no. 2154 00
Blind actuator 4-gang 230 V AC
Order no. 2160 00
Blind actuator 8-gang 230 V AC
Order no. 2161 00

Blind actuator
Table of Contents
1 Safety instructions ............................................................................................................ 3
2 Device components .......................................................................................................... 3
3 System information........................................................................................................... 4
4 Intended use..................................................................................................................... 4
5 Product characteristics ..................................................................................................... 4
6 Operation.......................................................................................................................... 5
7 Information for electrically skilled persons........................................................................ 8
7.1 Mounting ................................................................................................................ 8
7.2 Connect bus line .................................................................................................... 8
7.3 DC 24 V Venetian blind actuator: electrical connection ......................................... 9
7.4 Shutter actuators AC 230 V and roller shutter actuator: electrical connection..... 10
7.5 Commissioning .................................................................................................... 12
8 Technical data ................................................................................................................ 14
9 Troubleshooting.............................................................................................................. 16
10 Warranty ......................................................................................................................... 18
2 / 18
32560272 108707200 27.04.2023

1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled
persons.
Serious injuries, fire or property damage are possible. Please read and follow the
manual fully.
Danger of electric shock. Always disconnect before carrying out work on the device
or load. In so doing, take all the circuit breakers into account, which support danger-
ous voltages to the device and or load.
Risk of injury. Use the device only for controlling Venetian blind and roller shutter mo-
tors or awnings. Do not use it to switch other loads.
For parallel connection of several motors to an output it is essential to observe the
corresponding instructions of the manufacturing company, and to use a cut-off relay if
necessary. The motors may be destroyed.
Use only Venetian blind motors with mechanical or electronic limit switches. Check
the limit switches for correct mastering. Observe the information on the motors from
the manufacturing company. Device can be damaged.
Danger of electric shock on the SELV/PELV installation. Do not connect loads for
mains voltage and SELV/PELV together to the device.
This manual is an integral part of the product, and must remain with the customer.
2 Device components
Figure1
(1) Button field for manual operation
(2) Programming button and LEDs
(3) KNX connection
(4) Connection for mains supply
(5) Status LEDs for outputs
3 / 18
32560272 108707200 27.04.2023
Blind actuator

(6) Connection for Venetian blind motors
3 System information
System information
This device is a product of the KNX system and complies with the KNX directives.
Detailed technical knowledge obtained in KNX training courses is a prerequisite to
proper understanding.
The function of this device depends upon the software. Detailed information on load-
able software and attainable functionality as well as the software itself can be ob-
tained from the manufacturer´s product database. Planning, installation and commis-
sioning of the device are carried out with the aid of KNX-certified software. The latest
versions of product database and the technical descriptions are available on our
website.
4 Intended use
– Switching of electrically driven Venetian blinds, shutters, awnings and similar
hangings for AC 230 V mains voltage or DC 12...48 V extra-low voltage.
– Mounting on DIN rail according to DIN EN 60715 in sub-distribution unit
5 Product characteristics
– Outputs can be operated manually, construction site mode
– Blind/shutter position directly controllable
– Acknowledgement of the blind/shutter position in bus and manual mode
– Safety functions: 3 independent wind alarms, rain alarm, frost alarm
– Integration into the temperature management of the building
– Disabling of individual outputs manually or by bus
Delivery state: Outputs can be operated using button field, construction site
mode.
Only Venetian blind actuators:
– Automatic operation time detection for 230 V motors can be set
– Slat position directly controllable
– Acknowledgement of movement state and slat position in bus and manual
mode
– Scene function
– "Top" and "Bottom" forced position via higher-level controller
– Sun protection function
4 / 18
32560272 108707200 27.04.2023
Blind actuator

6 Operation
Operating elements
Figure2
(5) Status LEDs for outputs
(7) Button c – Manual operation
(8) LED c – on: continuous manual mode
(9) Button n: move hanging upwards / stop
(10) LED n – on: hanging moves up, manual mode
(11) Button o: move hanging downwards / stop
(12) LED o – on: hanging moves down, manual mode
(13) Button ALL OFF: stop all hangings
In operation with the button field the device distinguishes between a short and a long
press.
– Short: Pressing for less than 1 second
– Long: Pressing for between 1 and 5 seconds
Status indication
The status LED A1… (5) indicate the states of the outputs.
– Off: Output switched off
– On: Output switched on
– Flashes slowly: Output in manual mode
– Flashes quickly: Output disabled via continuous manual mode
Operating modes
– Bus operation: operation via push-button sensors or other bus devices
– Temporary manual operation mode: manual operation locally with button field,
automatic return to bus operation
– Permanent manual operation mode: exclusively manual operation on the
device
No bus operation is possible in manual mode.
No manual mode is possible in case of bus failure.
5 / 18
32560272 108707200 27.04.2023
Blind actuator

After a bus failure and restoration the device switches to bus operation.
After a power failure and restoration the device switches to bus operation.
The manual mode can be disabled in ongoing operation via a bus telegram.
Priorities
– Highest priority: manual mode
– 2th priority: forced position
– 3rd priority: safety function
– 4th priority: sun protection
– Lowest priority: bus mode: moving up/down, slat positioning, scenes, position-
ing
Switching on temporary manual operation mode
Operation using the button field is programmed and not disabled.
￭ Press the c button briefly.
LEDs A1 flash, LED c remains off.
After 5 seconds without actuating a button, the actuator returns automatically
to bus operation.
Switching off temporary manual operation mode
The device is in temporary manual operation mode.
￭ No button has been actuated for 5 seconds.
- or -
￭ Press the c button briefly as many times as necessary until the actuator exits
temporary manual operation mode.
LEDs A1... no longer flash, but rather indicate the output status.
Depending on the programming, the hangings move to the position that is act-
ive after the manual mode is switched off, e.g. to the forced position, safety or
sun protection position.
Switching on permanent manual operation mode
Operation using the button field is programmed and not disabled.
￭ Press the c button for at least 5 seconds.
LED c is illuminated, LEDs A1 flash, continuous manual mode is switched
on.
Switching off permanent manual operation mode
The device is in permanent manual operation mode.
6 / 18
32560272 108707200 27.04.2023
Blind actuator

￭ Press the c button for at least 5 seconds.
LED c is off, bus operation is switched on.
Depending on the programming, the hangings move to the position that is act-
ive after the manual mode is switched off, e.g. to the forced position, safety or
sun protection position.
Operating the outputs
The device is in permanent or temporary manual operation mode.
￭ Press the button c briefly as many times as necessary until the desired out-
put is selected.
LEDs of the selected output A1... flash.
The LEDs n and o indicate the status.
￭ Operate output with n button or o button.
Short: Stop hanging.
Long: Move hanging upwards/downwards.
The selected hanging executes the corresponding commands.
The LEDs n and o indicate the status.
Short-term manual mode: After running through all of the outputs the device
exits manual mode after another brief actuation.
Stop all hangings
The device is in permanent manual operation mode.
￭ Press the ALL OFF button.
All outputs switch off; all hangings stop moving.
Disabling individual outputs
The device is in permanent manual operation mode.
￭ Press the button c briefly as many times as necessary until the desired out-
put is selected.
The status LEDs of the selected output A1... flash.
￭ Press buttons n and o simultaneously for at least 5 seconds.
Selected output A1... is disabled.
The status LEDs of the selected output A1... flash quickly.
￭ Activate bus mode (see section Deactivating permanent manual control).
A disabled output can be operated in manual mode.
7 / 18
32560272 108707200 27.04.2023
Blind actuator

When a disabled output is selected in manual mode, the corresponding status
LEDs flash twice briefly at intervals.
Re-enabling outputs
The device is in permanent manual operation mode.
￭ Press the button c briefly as many times as necessary until the desired out-
put is selected.
The status LEDs of the selected output A1... flash twice briefly at time inter-
vals.
￭ Press buttons n and o simultaneously for at least 5 seconds.
Selected output A1... is enabled.
LEDs of the selected output A1... flash slowly.
￭ Activate bus mode (see section Deactivating permanent manual control).
7 Information for electrically skilled persons
7.1 Mounting
Mounting the device
DANGER!
Electric shock when live parts are touched.
Electric shocks can be fatal.
Always disconnect before carrying out work on the device or load. For this, switch off
all corresponding circuit breakers, secure against being switched on again and check
that there is no voltage. Cover up adjacent live parts.
DANGER!
Danger of destruction if several motors are connected in parallel to one output.
Limit switch contacts can weld together and motors, blinds/shutters and the venetian
blind actuator can be destroyed.
Observe the manufacturer's instructions. Use cutoff relay if necessary!
Observe the temperature range. Ensure sufficient cooling.
￭ Mount the device on DIN rail. Output terminals must be at the top.
7.2 Connect bus line
￭ Connect bus line with KNX device connection terminal observing the correct
polarity (see figure 3), (see figure 4).
8 / 18
32560272 108707200 27.04.2023
Blind actuator

￭ Attach the cover cap to the KNX connection as protection against hazardous
voltages.
7.3 DC 24 V Venetian blind actuator: electrical connection
Connecting the device
Image3: Connection example for DC Venetian blind actuator
Only for DC motors 12...48 V. Observe the admissible load ratings.
Terminals 1/2 supply power to the device electronics and outputs A1 and A2. For op-
eration of the actuator it is necessary to connect an external 24 V DC power supply
to 1/2.
Terminals 3/4 supply power to outputs A3 and A4.
The supply voltages must be designed in such a way that a safe and reliable operat-
ing voltage is provided under all load conditions – especially when the motors are first
switched on.
Do not connect any AC voltage.
￭ Connect power supply to terminals 1/2 or 3/4 (see figure 3).
￭ Connect motors to load terminals A1 ... A4 (see figure 3).
9 / 18
32560272 108707200 27.04.2023
Blind actuator

Drives for venting louvers or windows must be connected in such a way that
they open in travel direction "UP " and close in travel direction "DOWN".
7.4 Shutter actuators AC 230 V and roller shutter actuator: electrical
connection
Connecting the device without automatic operation time detection
Image4: Connection of bus and mains voltage supply
￭ Connect mains voltage supply (see figure 4).
￭ Connecting the motors (see figure 5).
￭ Mark 230 V use on label (see figure 5).
The N conductor connections (14) serve only to detect the operation time and
do not provide any N potential.
If motors with high-impedance inputs are connected, then the corresponding N
conductor can be connected. The associated output must not be under current
for a longer period without interruption due to retriggering. This can lead to im-
permissible heating of the device. Observe maximum duty cycle (see chapter
"Technical data").
10 / 18
32560272 108707200 27.04.2023
Blind actuator

Image5: Motor connection without automatic operation time detection
Connecting the device with automatic operation time detection
Image6: Motor connection with automatic operation time detection
Not for roller shutter actuator.
When appropriately programmed and wired, the Venetian blind actuator detects the
operation time of the individual hangings and saves them. The actuator measures the
voltage at the outputs against the connected neutral conductor (14), and uses it to
determine the end positions. During operation the Venetian blind actuator adjusts it-
self to changed operation times, e.g. due to ageing of the motors.
The automatic operation time detection cannot be used for 110 V AC motors,
DC motors, motors with electronic limit switches, or for motors that are con-
nected to the outputs using cutoff relays.
Only for 230 V AC motors with mechanical limit switches.
Automatic operation time detection is activated in the application software.
Hangings are not disabled.
￭ Connect mains voltage supply (see figure 4).
Connect only one motor per output.
￭ Connecting the motor (see figure 6).
￭ Connect the N conductor of the corresponding motor to the N conductor ter-
minals (14) (see figure 6). Note RCCB wiring.
￭ Mark 230 V use on label (see figure 6).
11 / 18
32560272 108707200 27.04.2023
Blind actuator

The N conductor connections for the individual outputs and mains voltage con-
nection are not connected internally.
If an output is energised without interruption for a prolonged time due to retrig-
gering, the device may heat up excessively. Observe maximum duty cycle
(see chapter "Technical data").
The automatic operation time detection is performed during commissioning
and the determined operation time is saved permanently.
Connecting the device for 12...48 V DC motors
Image7: Connection of DC motors
Not for roller shutter actuator.
The adjacent Venetian blind outputs A1 and A2 ... A7 and A8 can be used jointly to
switch a DC motor.
The Venetian blind drive actuator is programmed as a DC device.
￭ Connect mains voltage supply (see figure 4).
Connect only one motor per output.
￭ Connecting the motors (see figure 7).
￭ Mark 12-48 V use on label (see figure 7).
For DC operation, manual mode for outputs A2, A4... is without function. The
status LEDs indicate the relay states.
7.5 Commissioning
Measuring the hanging and slat operation time
The blind/shutter travelling time is important for position and scene runs. For slatted
Venetian blinds, the slat adjusting time is by design part of the overall blind travelling
time. The opening angle of the slats is therefore set as the operation time between
the positions "Open" and "Closed".
The upwards travel generally lasts longer than the downwards travel, and is taken
into account as the operation time extension in %.
12 / 18
32560272 108707200 27.04.2023
Blind actuator

￭ Measure upwards and downwards operation time of the hanging.
￭ Measure slat adjusting time between "Open" and "Closed".
￭ Enter the measured values in the parameter setting – Downwards travel in
seconds and operation time extension in percent.
In the case of automatic operation time detection, no measurement of the
hanging operation times is performed.
Automatic measurement of the slat adjusting time is not possible.
Load the address and the application software
￭ Switch on the bus voltage.
￭ Assign physical address.
￭ Load the application software into the device.
￭ Note the physical address on the device label.
Performing a reference movement
The Venetian blind drive actuator can only move to scenes and directly called posi-
tions if it has saved the positions of the hangings. To do this, each output has to per-
form a reference run.
￭ Move hangings to the upper end position.
￭ Wait until the output relay and the limit switch have switched off.
The venetian blind actuator does not save the hangings position permanently.
After a power failure and restoration it carries out another reference run.
Without a reference run, the Venetian blind actuator generates an internal "In-
valid position" message for each output that can be read out.
Automatic operation time detection: save operation times
Not for roller shutter actuator.
Only for 230 V motors.
When operation time detection is activated, the device can only set positions and
scenes when it has saved the operation times. The operation times must be saved
during interference-free conditions, i.e. no additional operations, no wind, no snow,
no obstructions.
Automatic operation time detection is activated in the application software.
The associated N conductors are connected for the outputs in question
(see figure 6).
Teaching runs must be performed only in manual mode or using commission-
ing software.
￭ Move hangings to the upper end position (see chapter "Perform reference
run").
13 / 18
32560272 108707200 27.04.2023
Blind actuator

Upper end position has been reached:
￭ Move hangings to lower end position in manual mode.
￭ Move hangings to upper end position in manual mode.
Operation times have been saved.
The Venetian blind actuator saves the operation times permanently.
Without saved operation times the Venetian blind actuator generates an in-
ternal "Invalid position" message for each output that can be read out.
During operation the Venetian blind actuator adjusts itself to changed blind
travelling times, e.g. caused by ageing of the motors. The slat operation time
is taken into account here. The changed times are only saved permanently in
continuous manual mode.
8 Technical data
Supply
Rated voltage
Order no. 2154 00 DC 12 ... 48 V =
Order no. 2160 00 AC 230 / 240 V ~
Order no. 2152 00 AC 230 / 240 V ~
Order no. 1039 00 AC 230 / 240 V ~
Order no. 2161 00 AC 230 / 240 V ~
Mains frequency
Order no. 2154 00 —
Order no. 2160 00 50 / 60 Hz
Order no. 2152 00 50 / 60 Hz
Order no. 1039 00 50 / 60 Hz
Order no. 2161 00 50 / 60 Hz
Power loss
Order no. 2154 00 max. 1 W
Order no. 2160 00 max. 4.5 W
Order no. 2152 00 max. 4.5 W
Order no. 1039 00 max. 4.5 W
Order no. 2161 00 max. 6 W
Ambient conditions
Ambient temperature -5 ... +45°C
Storage/transport temperature -25 ... +70 °C
Installation width
Order no. 2154 00 72 mm / 4 HP
Order no. 2160 00 72 mm / 4 HP
14 / 18
32560272 108707200 27.04.2023
Blind actuator

Order no. 2152 00 72 mm / 4 HP
Order no. 1039 00 72 mm / 4 HP
Order no. 2161 00 144 mm / 8 HP
Weight
Order no. 2154 00 approx. 300 g
Order no. 2160 00 approx. 300 g
Order no. 2152 00 approx. 250 g
Order no. 1039 00 approx. 300 g
Order no. 2161 00 approx. 550 g
Venetian blind outputs
Minimum switching current AC 100 mA
Switching current AC 250 V
Order no. 2154 00 --
Order no. 2160 00 AC 6 A
Order no. 2152 00 AC 6 A
Order no. 1039 00 AC 6 A
Order no. 2161 00 AC 6 A
Switching current DC 12 V
Order no. 2154 00 6 A
Order no. 2160 00 --
Order no. 2152 00 6 A
Order no. 1039 00 6 A
Order no. 2161 00 6 A
Switching current DC 24 V
Order no. 2154 00 6 A
Order no. 2160 00 --
Order no. 2152 00 6 A
Order no. 1039 00 6 A
Order no. 2161 00 6 A
Switching current DC 48 V
Order no. 2154 00 3 A
Order no. 2160 00 --
Order no. 2152 00 3 A
Order no. 1039 00 3 A
Order no. 2161 00 3 A
Blind/shutter travelling time max. 20 min
Duty cycle max. 50% (cycle time ≤ 40 min)
Automatic operation time adaptation
Order no. 2154 00 --
15 / 18
32560272 108707200 27.04.2023
Blind actuator

Order no. 2160 00 max. 20% of the blind/shutter travelling
time
Order no. 2152 00 max. 20% of the blind/shutter travelling
time
Order no. 1039 00 max. 20% of the blind/shutter travelling
time
Order no. 2161 00 max. 20% of the blind/shutter travelling
time
Connections supply and load
Connection mode Screw terminal
Clampable conductor cross-section (see figure 8)
Image8: Clampable conductor cross-section
KNX
KNX medium TP 1
Commissioning mode S-mode
Rated voltage KNX DC 21 ... 32 V SELV
Power consumption KNX typ. 150 mW
Connection mode KNX Standard device connection terminal
9 Troubleshooting
Manual control with button field not possible
Cause 1: Manual control has not been programmed.
Program manual control.
Cause 2: Manual control via bus disabled.
Enable manual control.
Output cannot be operated
Cause 1: Manual control has not been programmed.
Reprogram device.
Cause 2: Manual control via bus disabled.
Enable manual control.
16 / 18
32560272 108707200 27.04.2023
Blind actuator

None of the outputs can be operated
Cause 1: All of the outputs are disabled.
Cancel disabling.
Cause 2: Manual mode active.
Deactivate manual mode (switch off continuous manual mode).
Cause 3: Application software missing or faulty.
Check programming and correct.
Cause 4: Application software has been stopped, programming LED is flashing.
Disconnect device from the bus and mains, switch on again after 10 seconds.
Position- and scene runs are not executed or executed improperly
Cause 1: Sun protection, safety function or manual mode is activated.
As long as higher-order functions are active, no position or scene runs are pos-
sible.
Cause 2: No operation time saved.
Save operation times (see chapter "Automatic operation time detection: save
operation times").
Without saved operation times the venetian blind actuator moves the hangings
upwards or downwards for position and scene runs – depending on whether
the hangings are in the upper or lower half.
Cause 3: Automatic operation time detection is activated and N conductor is not con-
nected.
Correct electrical connection.
- or -
Deactivate automatic operation time detection.
Cause 4: Automatic operation time detection is activated, but the switching voltage is
< 230 V or motors with electronic limit switches are being used.
Deactivate automatic operation time detection.
Correct electrical connection and remove N conductor.
Hanging does not move to end position, position and scene runs faulty
Cause: Blind/shutter travelling time has been set incorrectly.
Correct blind/shutter travelling time.
17 / 18
32560272 108707200 27.04.2023
Blind actuator

10 Warranty
The warranty is provided in accordance with statutory requirements via the specialist
trade. Please submit or send faulty devices postage paid together with an error de-
scription to your responsible salesperson (specialist trade/installation company/elec-
trical specialist trade). They will forward the devices to the Gira Service Center.
Gira
Giersiepen GmbH & Co. KG
Elektro-Installations-
Systeme
Industriegebiet Mermbach
Dahlienstraße
42477 Radevormwald
Postfach 12 20
42461 Radevormwald
Deutschland
Tel [phone] - 602-0
Fax [phone] - 602-191
www.gira.de
[email protected]
18 / 18
32560272 108707200 27.04.2023
Blind actuator