GLP YPOC 250 Color User manual

Instruction Manual
from software version 1.19
(instruction version 1.42)
e-mail: servic[email protected]
Internet: http://www.GLP.de

GLP German Light Production (V1.42) 2
This side is intentionally unlabelled.

GLP German Light Production (V1.42) 3
Table of contents
1Description of Device.............................................................................................5
1.1 Safety Instructions............................................................................................6
2Preparation and Installation ..................................................................................7
2.1 Mounting ..........................................................................................................7
2.1.1 Clamps...................................................................................................7
2.1.2 Mounting plate.......................................................................................8
2.2 Secure the Y YP PO OC C 2 25 50 0 C CO OL LO OR R........................................................................8
2.3 Connections.....................................................................................................9
2.3.1 Power supply.........................................................................................9
2.3.2 DMX.......................................................................................................9
2.4 Fuse.................................................................................................................9
3The Menu Field......................................................................................................10
3.1 Adjust the DMX- Address (D001).....................................................................11
3.2 The Audio Program (AUDI)..............................................................................11
3.3 The Test Program (TEST) ................................................................................11
3.4 Lamp On/Off (LAMP) ........................................................................................12
3.5 Reset (RESE) ...................................................................................................12
3.6 Running time of lamp and unit (TIME) .............................................................12
3.7 Continuous Color Wheel (FCOL)......................................................................12
3.8 Invert Pan Movement (RPAN)...........................................................................12
3.9 Invert Tilt Movement (RTLT) ............................................................................13
3.10 Special Functions (SPEC).................................................................................13
3.10.1Manual Drive (MANU) .............................................................................13
3.10.2Lamp On automatically (LAAU)..............................................................14
3.10.3Lamp Off via DMX (DLOF) .....................................................................14
3.10.4DMX Input (DMXI) .................................................................................14
3.10.5Display (DISP).......................................................................................15
3.10.6Fixture Temperature (TEMP) ..................................................................15
3.10.7Fan Control (FANS)................................................................................15
3.10.8Adjustments and Calibrations (ADJU)....................................................16
3.10.9Default Settings (DFSE) .........................................................................16
3.10.10 Feedback (FEED)..............................................................................17
3.10.11 Correction of faults (EFLD) ...............................................................17
3.11 Error and Information Messages....................................................................17

GLP German Light Production (V1.42) 4
4DMX Channel Selection (DMX Protocol).............................................................18
5Change the Lamp..................................................................................................20
5.1 Safety Regulations .........................................................................................20
5.2 Realize the Lamp Change..............................................................................20
6Maintenance and Cleaning the Y YP PO OC C 2 25 50 0 C CO OL LO OR R ............................................20
6.1 Safety Regulations .........................................................................................21
6.2 Circumference and Interval (rule-of-thumb)....................................................21
6.3 Cleaning the Optical System..........................................................................22
7Technical Specification........................................................................................23
8Index ......................................................................................................................24

GLP German Light Production (V1.42) 5
1 Description of Device
1
2
34
1. Moving Head
2. Arm
3. Base
4. Carrying handles
5. Up- button
6. Down- button
7. Enter- button
8. Mode- button
9. LED- Display
10.Software-Update
connector
11.Microphone- Intensity
12.DMX- Input
13.DMX- Output
14.Power On/Off
15.Fuse F3,15 A
16.Fan (air inlet)
MaxMin
DMXIN DMXOUT
Software U
p
date
1.Groun d
2.Data -
3.Data +
POWER
210V ~
230V ~
250V ~
50Hz
60Hz
Power in
p
ut
FUSE:
T3.15A@250V
LAMP:
MSD 250W
Serial
num ber:
Fuse
Mi c Sen sit ive
12
3
PUSH
FUSE
MODE ENTER UPDOWN
MODEENTERUP DOWN
87 65
9
10
11
12 13 14
15
16
COLOR
COLOR

GLP German Light Production (V1.42) 6
1.1 Safety Instructions
The Y YP PO OC C 2 25 50 0 C CO OL LO OR R is a High-Tech Product. To guarantee a
smooth operation, it is necessary to keep following rules.
The manufacturer of this device will not take responsibility of
damages through disregard of the information in this manual.
Warranty adjustments will be canceled.
1. Make sure before putting into operation, that the fan and the air inlets are
clean and not blocked by anything.
2. Attention: Don’t touch the device during the operation. This can cause
injuries or damages.
3. Unplug the
Y
YP PO OC C 2 25 50 0 C CO OL LO OR R from the AC outlet before any service.
4. It is necessary to wait at least 30 minutes after disconnecting the AC before
you open the Y YP PO OC C 2 25 50 0 C CO OL LO OR R. Please do not touch the bulb of the lamp if
you are not absolutely sure it is cold. -DANGER OF BURNING-
5. Never look directly into the beam of the lamp. You risk injury of your retina and
blindness.
6. Pay attention of the maximum lamp operation time. You have to change it if
the lamp shows any deformations or damages. The same is with all glass
components, color filters, lenses and mirrors.
7. To allow a secure operation, follow also the Installation guide described in
chapter 2. Operating the Y YP PO OC C 2 25 50 0 C CO OL LO OR R without suited safety aids like
Safety cables or clamps/hooks can increase the risk of an accident.
8. The installation should be done by qualified staff only. You need to pay
attention to the common rules of technology that are not explicit mentioned in
this manual.
9. Use only original spare parts. Any structural modification will cancel all
warranty adjustments.

GLP German Light Production (V1.42) 7
2 Preparation and Installation
2.1 Mounting
The Y YP PO OC C 2 25 50 0 C CO OL LO OR R is fully operational whether it hangs or is mounted to the
wall. It can also be operated while standing on the floor. Keep a safety distance of
0.5 m towards any easy inflammable materials (decoration etc.). Install a safety
wire that can hold at least 10 times the weight of the fixture. Never use the
carrying handles for secondary attachment.
Pay attention to the regulations of: BGV C1 (former VBG 70)
and DIN VDE 0711-217 !
The installation should be done by qualified staff only.
2.1.1 Clamps
Use two clamps on the backside of the Y YP PO OC C 2 25 50 0 C CO OL LO OR R to mount the
unit on a truss (each two opposite threads max. M10x20). See also printing
on the backside of the case.

GLP German Light Production (V1.42) 8
2.1.2 Mounting plate
For a permanent installation of the Y YP PO OC C 2 25 50 0 C CO OL LO OR R you can use a
optional mounting plate to fix the unit on a wall. The plate uses 4x screws
M6x20.
2.2 Secure the
Y
YP PO OC C 2 25 50 0 C CO OL LO OR R
Regardless of the rigging of the Y YP PO OC C 2 25 50 0 C CO OL LO OR R you have to use a stipulated
safety wire. Therefore you have to thread to safety wire through to two provided
holes on the backside of the fixture and connect it with the truss-support. Pay
attention to a safe and proper fastening.

GLP German Light Production (V1.42) 9
2.3 Connections
2.3.1 Power supply
230 Volt, 50 Hz,
Connected load 500W <=> 2,2 A (blind current compensation).
or 115V, 60 Hz
Connected load 500W <=> 4,4 A (blind current compensation).
Please see printing on the case for the right Power supply!
2.3.2 DMX
DMX 512 Standard input/output. See also printing on the case for the right
pin assignment.
[+] = Pin 3 / [-] = Pin 2 / [Ground] = Pin 1
The DMX- Addressing starts at the DMX- Address [001].
2.4 Fuse
The Y YP PO OC C 2 25 50 0 C CO OL LO OR R electronic system is protected by a 5x20 mm fuse.
230V / T 3,15A (EU model) or 115V / T 6,3A (US model)
Please see the printing on the Y YP PO OC C 2 25 50 0 C CO OL LO OR R for more details.
Attention:
• Disconnect AC outlet before changing a fuse!
• Use only the original declared fuse type!

GLP German Light Production (V1.42) 10
3 The Menu Field
You find the control board on the side part of the base. It allows you
to make all necessary adjustments of the Y YP PO OC C C CO OL LO OR R. .With the
Mode-key you get into the main menu. Afterwards you can navigate
through the menu with the Up/Down-keys. Push the Enter-key to get
in the next menu level or to confirm your settings. Make them and set
functions ON/OFF with the Up/Down-keys. Confirm and save it with
the Enter-key (the display shows OK). Push the Mode-key to cancel
the entry and go back to the main menu.
MODE ENTER UP DOWN
M O D EE N T E RU P D O W N
LED-Display
Mode-key Enter-key Down-key Up-key
Level 1 Level 2 Level 3 Remark
D001
Define the DMX start address
TEST
Test program of all functions
AUDI ASLW Self-running audio program (slow)
AFST Self-running audio program (fast)
MSTR Master for the audio program
SVPT Basic position for the audio program
SIZE Size for the audio program (NORM-BIG-MIDL-SMAL)
LAMP
Switch on/of the lamp direct at the Y
YP PO OC C 2 25 50 0 C CO OL LO OR R
RESE
Reset
TIME POWR Running time of the fixture (no destructible)
LA1 Running time of the lamp (erasable)
LA2 Running time of the lamp (no destructible)
FCOL
Continuously movement of the color wheel
RPAN
Reverse Pan-direction
RTLT
Reverse Tilt-direction
SPEC MANU Manual drive of all device functions
LAAU Automatic lamp start
DLOF Switch off lamp via DMX
DMXI Reed out actual DMX-values
DISP D ON Display On/Off
REV Twist the display
TEMP Reed out internal temperature
FANS HIGH Maximum cooling fan velocity
REG Automatic cooling fan control
LOOF Low cooling fan speed Ælamp off
LOHI Low cooling fan speed Æautomatic
ADJU CODE
xxxx
Use the code for entering the calibration menu (for
authorized person only)
COLO Calibration of the color wheel
BSPR Calibration of the beam shape
clre Settings in the internal memory (superuser only)
facc Must read on. Protected by a code
ARES Adjust- Rest
DFSE Call on the default function values
FEED Pan/Tilt feedback (error correction) On/Off
ÅDOWN - UP Æ
EFLG Correction of faults

GLP German Light Production (V1.42) 11
3.1 Adjust the DMX- Address (D001)
Right after turning on the Y YP PO OC C 2 25 50 0 C CO OL LO OR R you can see the current DMX-
Address. If there is no DMX- Signal the display flashes.
D001
For the address setting please follow this procedure:
1. Switch On the
Y
YP PO OC C 2 25 50 0 C CO OL LO OR R and wait until the fixture reset has finished
('RESE'is flashing in the display).
2. Press the Mode-key in order to access the main menu. Browse through the
menu by pressing the Up/Down-keys until the display shows D001. Confirm by
pressing the Enter-key (the decimal point is flashing)
3. Use the Up/Down-keys to select the desired address. Confirm the setting by
pressing the Enter-key (the display shows OK) or press the Mode-key to
cancel.
The DMX- Address is stored also while switching off the Y YP PO OC C C CO OL LO OR R!
3.2 The Test Program (TEST)
Test
The Test-Program allows you to run a complete self test procedure of all
functions. Press Enter to confirm or Mode to cancel.
3.3 The Audio Program (AUDI)
The Audio-menu allows you to run a stand alone audio program. This chaser can
run either fast or slow. AFST: Every sound impulse on step of the chaser. Aslw:
Every second sound impulse one step of the chaser.
Additional you can choose a basic position for this audio chaser. Use therefore
either the internal manual mode or an external controller to set the desired
Pan/Tilt position. Confirm this setting in the SPCT menu by pressing the Enter-key.
You can also set the size of the audio chaser in the SIZE menu. You have the
choice between: NORM (no basic position has to bee chosen), 'BIG', 'MIDL' and
'SMAL').
If you want to run the systems simultaneously, one of the Y YP PO OC Cs smust be

GLP German Light Production (V1.42) 12
switched as the master. All others must be "Slave" Master = OFF. Notice: The
Audio function is only working when no DMX is connected. This function can work
e.g. on small events or as an emergency program.
3.4 Lamp On/Off (LAMP)
LAMP
Use the Up/Down-keys to select lamp On or lamp Off Press Enter to confirm or
Mode to cancel and return to the main menu. (The lamp OFF command is only
working if the shutter is closed at the same time. Use an external controller or the
manual drive mode, see 3.10.1 on page 13.
3.5 Reset (RESE)
RESE
Press the Enter-key to run a reset of all fixture functions (RST is shown in the
display).
3.6 Running time of lamp and unit (TIME)
TIME
By this option can read out three different running times of the fixture.
POWR Running time of the fixture (no destructible).
LA 1 Running time of the lamp (erasable). Push the Up/Down-keys at one
time to delete this running time.
LA 2 Running time of the lamp (no destructible).
3.7 Continuous Color Wheel (FCOL)
FCOL
This function allows you to control the color wheel continuously. If it is switched
off, the color wheel is stepping directly from one to another color.
3.8 Invert Pan Movement (RPAN)
RPAN

GLP German Light Production (V1.42) 13
This function allows you to invert the Pan movement. Use the Up/Down-keys to
select invert On or Off. Press Enter to confirm or Mode to cancel and return to the
main menu.
3.9 Invert Tilt Movement (RTLT)
RTLT
This function allows you to invert the Tilt movement. Use the Up/Down-keys to
select invert On or Off. Press Enter to confirm or Mode to cancel.
3.10 Special Functions (SPEC)
SPEC
This menu allows you to enter further special functions of the Y YP PO OC C 2 25 50 0 C Co ol lo or r. .
In detail they are:
3.10.1 Manual Drive (MANU)
MANU
This function allows you to drive all the fixture functions manually. Select
the desired function with the Up/Down-keys and confirm with Enter. Now
choose the desired value with the Up/Down-keys and confirm again with
Enter or cancel and return to the menu with the Mode-key.
Function Value Remark
PAN 000 - 255 Pan Position
TILT 000 - 255 Tilt Position
CYAN 000 - 255 Cyan color mixing
MAGE 000 - 255 Magenta color mixing
YELL 000 - 255 Yellow color mixing
COLO 000 - 255 Color wheel (fixed colors)
SHUT 000 - 255 Shutter / Strobe function (the lamp strikes at
DMX 255 if dimmer is "open" = DMX 255)
DIMR 000 - 255 Dimmer
BSPR 000 - 255 Beamshape + Frost
SPEC 000 - 255 Lamp Off, Reset, ...

GLP German Light Production (V1.42) 14
3.10.2 Lamp On automatically (LAAU)
LAAU
This function enables to switch On the lamp automatically after switching
On the fixture. Use the Up/Down-keys to select ON if you want to switch on
the lamp automatically after switching on the fixture or Off if you don't want
this function. Press Enter to confirm or Mode to cancel and return to the
menu. If you have chosen off you have the possibility to start the lamp
either via DMX or direct at the Y YP PO OC C 2 25 50 0 C CO OL LO OR R in the Lamp menu.
3.10.3 Lamp Off via DMX (DLOF)
DLOF
This function enables to switch off the lamp via DMX or not. Use the
Up/Down-keys to select ON if you want to switch off the lamp via DMX or
Off if you don't want this function. Press Enter to confirm or Mode to
cancel and return to the menu.
3.10.4 DMX Input (DMXI)
DMXI
Readout DMX values of each channel received by the fixture. Use the
Up/Down-keys to select desired channel and press Enter to read its value.
Function Value Remark
PAN 0 - 255 Pan Position
TILT 0 - 255 Tilt Position
CYAN 0 - 255 Cyan color wheel
MAGE 0 - 255 Magenta color wheel
YELL 0 - 255 Yellow color wheel
COLO 0 - 255 Color wheel (fixed colors)
SHUT 0 - 255 Shutter / Strobe function
DIMR 0 - 255 Dimmer
FOCU 0 - 255 Focus
SPEC 0 - 255 Lamp Off, Reset, ...

GLP German Light Production (V1.42) 15
3.10.5 Display (DISP)
DISP
Use this function to choose between different display indications. Use the
Up/Down-keys to select desired function and press Enter to confirm or
Mode to cancel and return to the menu.
D ON Display On/Off (If you've chosen off, the display will go out
within 15 seconds after the last input. The next key touch will
reactivate the display).
REV Turn around the display
3.10.6 Fixture Temperature (TEMP)
TEMP
This function allows you to read out the actual temperature of the Y YP PO OC C
2
25 50 0 C Co ol lo or r. Press Enter to confirm or Mode to cancel. Inside temperatures
below 80°C are not critical. 80°C and more lead the lamp being switched
off at a critical point. Please note for a save operation that the outside
temperature should not exceed 45°C.
3.10.7 Fan Control (FANS)
FANS
By using this function you can choose between 4 types of fan speed
operations. Use the Up/Down-keys to select desired function and press
Enter to confirm or Mode to cancel and return to the menu.
HIGH The cooling fan works continuously at max. speed.
REG The fan automatically raises its speed in order to control inside
temperature of the fixture.
LOOF The fan keeps the adjusted low speed until the temperature
exceeds max. inside temperature, then the Y YP PO OC C 2 25 50 0 C CO OL LO OR R
automatically switch off the lamp.
LOHI The fan keeps the adjusted low speed until the temperature
exceeds max. inside temperature, then the Y YP PO OC C 2 25 50 0 C CO OL LO OR R
automatically switch from low to high fan speed.

GLP German Light Production (V1.42) 16
3.10.8 Adjustments and Calibrations (ADJU)
ADJU
By this function you can adjust and calibrate the positions of the different
wheels and other motors. This can be necessary after a service or repair
work.
For this function you have to entry the fixture code. This work should be
done only by authorized persons.
Use the Up/Down-keys to select desired function and press Enter to
confirm or Mode to cancel and return to the menu. Use now the Up/Down-
keys to set the adjustment values and confirm once more with the Enter-
key or cancel with the Mode-key.
Function Value Remark
COLO - 99 - + 99 Color wheel
BSPR - 99 - + 99 Beamshape
CLRE Adjustments in the internal circuit.
FACC Must read ON
ARES Adjust- Reset
For authorized
persons only
Æ Service manual
3.10.9 Default Settings (DFSE)
DFSE
Press Enter to reset all fixture personalities (not the adjusted functions) to
the default values. On the display will appear ok to indicate that the
defaults are set.
Function Display Default Settings
DMX Address D001 D001
Pan reverse RPAN ON OFF 9
Tilt reverse RTLT ON OFF 9
Automatic lamp on LAAU ON OFF 9
Lamp on via DMX DLOF ON 9OFF
Display DISP D ON 9
Cooling fan FANS HIGH REG 9LOOF LOHI
Feedback FEED ON 9OFF

GLP German Light Production (V1.42) 17
3.10.10Feedback (FEED)
FEED
The Y YP PO OC C 2 25 50 0 C CO OL LO OR R is provided with a automatic position correction
(feedback) for the Pan and Tilt movement. Use the Up/Down-keys to
select ON if you want to enable the feedback function or Off if you don't
want this function. Press Enter to confirm or Mode to cancel and return to
the menu.
3.10.11Correction of faults (EFLD)
(Function available for authorized persons only)
3.11 Error and Information Messages
HEAt This message appears if you try to switch on the lamp within 5
minutes after having switched off (lamp too hot). The message
will appear on the display if the lamp doesn’t ignite within 20
seconds. The fixture will store this command and automatically
ignite the lamp after 5 minutes.
LaeR After the ignition of the lamp was two times not successful the
display will show LAER. That means the lamp could be damaged
or even missed, the fixture is overheating or there could be a
failure on the igniter or ballast. Switch off the power supply and
solve the possible problem.
OTMP This error message informs you that the fixture was overheating
and that the relay switches off the lamp. Pleas look for possible
reasons (fan faulty, air in/outlets blocked or very dirty, lamp
broken or very old, too high ambient temperature. Switch off the
power supply and solve the possible problem.
RsER This message informs you that one of the fixture function wasn’t
able to do its reset correct (magnetic sensor, stepping motor,
driver on the PCB, cables, etc.). Repair the defect and start the
fixture again.
EFLG

GLP German Light Production (V1.42) 18
4 DMX Channel Selection (DMX Protocol)
Channel Function Time and Value DMX HEX %
1) PAN-coarse 0 .. 530° min. 2.65 s 0..255 00..FF 0..100
2) PAN-fine Low- Pos ... High- Pos + 2.1° (16 Bit) 0..255 00..FF 0..100
3) Tilt-coarse 0 .. 285° min. 1.8 s 0..255 00..FF 0..100
4) Tilt-fine Low- Pos … High- Pos + 1.1° (16 Bit) 0..255 00..FF 0..100
open (fast) 0..3 00..03 0,2
color 1, Brilliant Blue (fast) 4..7 04..07 1,8
color 2, Blue (fast)
Chaser from color to
color max. 140 BPM
Æ0,43 s 8..11 08..0B 3,3
color 3, Blue Purple (fast) 12..15 0C..0F 4,9
color 4, Pink (fast) 16..19 10..13 6,5
color 5, Orange (fast) 20..23 14..17 8,0
color 6, Italian Blue (fast) 24..27 18..1B 9,6
color 7, Turquoise (fast) 28..31 1C..1F 11,2
color 8, Jade (fast) 32..35 20..23 12,7
color 9, CTB 001 (fast) 36..39 24..27 14,3
color 10, CTO 02 (fast) 40..43 28..2B 15,9
color 11, Red (fast) 44..47 2C..2F 17,5
open (fast) 48..63 30..3F 19,0
open (slow) 64..67 40..43 25,3
color 1, Brilliant Blue (slow) 68..71 44..47 26,9
color 2, Blue (slow)
Chaser from color to
color max. 70 BPM
Æ0,86 s 72..75 48..4B 28,4
color 3, Blue Purple (slow) 76..79 4C..4F 30,0
color 4, Pink (slow) 80..83 50..53 31,6
color 5, Orange (slow) 84..87 54..57 33,1
color 6, Italian Blue (slow) 88..91 58..5B 34,7
color 7, Turquoise (slow) 92..95 5C..5F 36,3
color 8, Jade (slow) 96..99 60..63 37,8
color 9, CTB 001 (slow) 100..103 64..67 39,4
color 10, CTO 02 (slow) 104..107 68..6B 41,0
color 11, Red (slow) 108..111 6C..6F 42,5
open (slow) 112.127 70..7F 44,1
color rotation, slow-fast, CW min. 1.4 turns/h 128..191 80..BF 50..75
color rotation, fast-slow, CCW max. 2.9 turns/sec. 192..253 C0..FD 76..98
Audio color chaser slow each 4th sound impulse
Ænew color 254 FE 99
5) Color*
Audio color chaser fast each sound impulse
Ænew color 255 FF 100
6) Cyan Cyan color intensity 0% - 100% 0..255 00..FF 0..100
7) Magenta Magenta color intensity 0% - 100% 0..255 00..FF 0..100
8) Yellow Yellow color intensity 0% - 100% 0..255 00..FF 0..100
Shutter closed 0..15 00..0F 0..6
Random Strobe (different pattern) 16..31 10..1F 7..11,9
Strobe Pulse effect , slow - fast min. frequency 0,7 Hz 32..47 20..2F 12..12,9
Strobe effect , slow - fast max. frequency 10 Hz 48..239 30..EF 13..93
Shutter open 240..255 F0..FF 94..100
9) Shutter
Lamp ON (ignition) 254..255 FE..FF 99..100
Dimmer closed (0%) 0..3 0..3 0..1
Dimmer 1%...99% movement time 0,3 Sek. 4..251 4..FB 2..98
10) Dimmer
Dimmer open (100%) 252..255 FC..FF 99..100
Open 0..15 0..0F 0..5
Shaper 16..239 10..EF 6..94
11) Beam
shape Frost 240..255 F0..FF 95..100

GLP German Light Production (V1.42) 19
Channel Function Time and Value DMX HEX %
No function 0..15 00..0F 0..6
Audio CMY chaser slow 16..23 10..17 7..9
Audio CMY chaser fast 24..31 18..1F 10..12
Rotating color chaser 32..63 20..3F 13..24
Color chaser C / C+1
slow – fast 64..79 40..4F 25..31
Color chaser C / C+2
slow – fast 80..95 50..5F 32..37
PAN/Tilt chaser slow 96..111 60..6F 38..43
PAN/Tilt chaser fast 112..127 70..7F 44..50
Lamp OFF
(only if shutter is closed)! 230..249 E6..F9 92..97
12) Special
Reset 250..255 FA..FF 98..100
No movement 0 00 0
13) Movement Movement Size Phase
PAN 1 0° 01..01 01..01 0,5
1 90° 02..03 02..03 1,0
1 180° 04..05 04..05 1,7
1 270° 06..07 06..07 2,5
PAN 2 0° 08..09 08..09 3,3
2 90° 10..11 0A..0B 4,1
2 180° 12..13 0C..0D 4,9
2 270° 14..15 0E..0F 5,7
PAN 3 0° 16..17 11..11 6,5
3 90° 18..19 12..13 7,3
3 180° 20..21 14..15 8,0
3 270° 22..23 16..17 8,8
PAN 4 0° 24..25 18..19 9,6
4 90° 26..27 1A..1B 10,4
4 180° 28..29 1C..1D 11,2
4 270° 30..31 1E..1F 12
TILT size / phase see also PAN 32..63 20..3F 13..25
PAN / TILT size / phase see also PAN 64..95 40..5F 26..37
PAN / TILT (inverse) size / phase see also PAN 96..127 60..7F 38..50
Circle size / phase see also PAN 128..159 80..9F 51..62
Circle (inverse) size / phase see also PAN 160..191 A0..BF 63..75
lying eight size / phase see also PAN 192..223 C0..DF 76..87
random movement size see also PAN 224..255 E0..FF 88..100
Pan/Tilt relative movement 0..15 00..0F 0..6
14) Speed
Pan/Tilt Pan/Tilt slow – fast
Use this channel 14) also for the
speed of the movements (channel
13).
Pan Min. 530° = 200 s
Pan Max. 530° = 2.65 s
Tilt Min. 285° = 110 s
Tilt Max. 285° = 1.8 s
16..255 10..FF 7..100
Lamp ON Shutter open 254..255 FE..FF 99..100
Lamp OFF Channel 12 ( min. 3 sec. ) (only if
shutter is closed, channel 9 = 0 ..15) 230..249 E6..F9 92..97
*) Set the function “FCOL” ‘ON’ if you want to control the color wheel continuously.

GLP German Light Production (V1.42) 20
5 Change the Lamp
For a frictionless operation pleas read this chapter carefully and follow all instructions.
5.1 Safety Regulations
• Pull out the main plug!
• Wait min. 20 minutes after the last operation to cool down the fixture.
• Don’t touch the bulb of the lamp with bare fingers (this can cause damages.
• Before you put the Y YP PO OC C 2 25 50 0 C CO OL LO OR R into operation close the casing,
otherwise your retina can be hurt!
5.2 Realize the Lamp Change
1. Pull out the main plug!
2. Open the three screws on the backside of the unit.
3. Pull out the lamp sheet together with the lamp holder securely.
4. Remove the old or broken lamp out of the socket. Attention: The glass bulb of
the lamp can splinter. For that reason remove the lamp with safety gloves or
some cloth.
5. Put in the new lamp securely into the socket. Attention: Use only the original
lamp type and do not touch the lamp with bare fingers.
6. Put the lamp sheet back into the unit.
7. Close the three screws.
8. Adjust the optimum light output with the tree adjustment screws on the
backside.
9. The running time of the lamp LA1 can be reseed in the Time Menu.
6
6 Maintenance and Cleaning the Y YP PO OC C 2 25 50 0 C CO OL LO OR R
It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid
residues must not built up on or within the fixture. Otherwise the fixture's light-output will
be significantly reduced. Regular cleaning will not only ensure the maximum light-
output, but will also allow the fixture to function reliable throughout its life.