Goldmedal P-60 User manual

P-60 and 60 Special
Popcorn MachineInstruction Manual
Model #2085JX and Model #2086JX
PartNo.49064EX
RevisedJune 1996
Cincinnati, OH 45241-4807 USA
Model #2086JX
Model #2085JX
BACK TO INDEX

SAFETY PRECAUTIONS
NOTE
The information, specifications and illustrations contained in this manual represent
the latest data available at time of publication. Right is reserved to make changes as
required at the discretion of Gold Medal Products Company without notice.
Any alterations to this equipment will void the warranty and
may cause a dangerous situation. NEVER make alterations
to the equipment.
Make sure all machine switches are in the OFF position
before plugging the equipment into a receptacle.
Always wear safety glasses when servicing this equipment.
Machine must be properly grounded to prevent electrical shock
to personnel.
Do NOT immerse the kettle, warmer, or any other part of this
equipment in water.
Always unplug the equipment before cleaning or servicing.
This equipment is designed and sold for commercial use only. This
equipment is not to be used by the consumer in home use. Do not allow
direct contact of this equipment by the public when used in food service
locations. Only personnel trained and experienced in the equipment
operation may operate this equipment.
Carefully read all installation instructions before operating the equipment.
To avoid serious burns, do NOT touch the kettle while it is hot.

1
60 Special and P-60
ALL EXPORT MODELS #1866, #2085, #2086AND #2656
INSTALLATION INSTRUCTIONS
INSTALLATION
Your new 60 Special or P-60 Popcorn Machine is completely assembled. Remove all packing
material and tape before starting operation.
OPERATING INSTRUCTIONS
CONTROLS AND THEIR FUNCTIONS
There are three switches on the popper.
LIGHT AND WARMER SWITCH
Turns on the heat to the bottom corn pan and heat light.
KETTLE MOTOR SWITCH
Turns on the motor which drives kettle agitator shaft.
KETTLE HEAT SWITCH
Turns on the heat element
AMOUNT OF POPCORN AND OIL
Your new popper is equipped with a six ounce (177 ml) corn measure cup. We recommend
flavored and colored coconut oil. Popcorn popped in coconut oil stays fresh longer. Coconut
oil does not leave black deposits in your kettle like other oils.
Corn charge - 6 oz. (177 ml)
Oil charge - 1.6 to 2.0 oz. (60 ml)
Flavacol - 1 tablespoon (8 cc)
POPPING INSTRUCTIONS
1. Turn KETTLE HEAT and KETTLE MOTOR switch ON.
2. Make test pop with 3 kernels of corn and 1 oz. (30 ml) of oil.
3. Load pre-measured popcorn and oil pouch into kettle.
4. When corn has popped, dump kettle.
5. Repeat cycle starting with Item #3; always pop 3-5 batches for best
popcorn.
To avoid
serious
burns, do
NOT touch
the kettle
while it is hot!

2
60 Special and P-60
ALL EXPORT MODELS #1866, #2085, #2086AND #2656
CARE AND CLEANING
Each time you finish a series of poppings, wipe the outside of the kettle with a soft cloth to remove
any oil drippage on the outside of the kettle. After you finish popping for the day, allow kettle to
cool until it is not too hot to handle, but still warm. Unplug kettle and remove it from the machine.
With a cloth, wipe out the inside of the kettle, kettle lid, crossbar, outside and underneath of the
kettle.
Cleaning the cabinet of your machine is easy. Take a clean cloth and wipe excess grease from
the glass. Wipe the outside of the machine also. NOTE: Never use a glass or plastic cleaner that
contains ammonia. It will crack the plastic on the machine.
Unplug your machine bofore cleaning glass panel and case.
Never immerse the kettle in water. This will ruin the electrical
components and automatically void the guarantee.

3
60 Special and P-60
ALL EXPORT MODELS #1866, #2085, #2086AND #2656
ACCESSORIES
MAINTENANCE INSTRUCTIONS
THE FOLLOWING SECTIONS OF THIS MANUAL ARE IN-
TENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO
ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE
NOT INTENDED FOR THE OPERATOR.
Adequate eye protection must be used when servicing this
equipment to prevent the possibility of injury.
Do NOT immerse the kettle, warmer, or any other part of this
equipment in water.
Unplug your machine before servicing.
Description Part Number
Shipping Carton 49026
Corn Measure Cup 49049
A-Scoop 47145
Flavacol Cup 47678
Popper Cleaning Towel 47660

4
60 Special and P-60
ALL EXPORTMODELS#1866, #2085, #2086AND #2656
ORDERING SPARE PARTS
1.Identify the desired part by checking it against the photos, illustrations, and/or the parts list.
2.When ordering, please include part number, part name, and quantity desired.
3.Please include your model name and machine serial number (located on the machine
nameplate) with your order.
4.Address all parts orders to: Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
or, place orders at:
[phone]
Fax: [phone]
E-mail: [email protected]

5
60 Special and P-60
ALL EXPORT MODELS #1866, #2085, #2086AND #2656
60 SPECIAL & P-60 POPPER ASSEMBLY

6
60 Special and P-60
ALL EXPORT MODELS #1866, #2085, #2086AND #2656
PARTS LIST - HANGER ASSEMBLY
Item No. Part No. Description
1-0 49336JX Complete Hanger Assembly
1-1 41033 Red Pilot Light
1-2 41671 Reflector Flood Light
1-3 41742 Set Screw #10-32 x 3/16" (4,8mm)
46544 ¼" (6,4mm) Faston #18-16 AWG.
47004 Pop Rivet, Closed End
1-4 47047 Lamp Holder
1-5 47065 Gear Box w/ Bushing
1-6 47058 Flange Bushing
47153 ¼" (6,4mm) Faston #14-10 AWG.
1-7 47059 Spur Gear
1-8 47201 Switch
1-9 49010 Front Hanger Arm
1-10 49009 Rear Hanger Arm
1-11 49480 Light Shield
1-12 47799 Light Shield Angle
1-13 49099 Switch Box
1-14 47121 Kettle Drive Motor
1-15 49116 Label, Switches
49133 Dead-end Splice
49130 Nut, Flexlock #10-24 THD.
1-16 41452 Warning, Max Lamp 75W
1-17 49330 Receptacle Assembly
49341 Black Receptacle Wire Assembly
49342 White Receptacle Wire Assembly
49343 Green Receptacle Wire Assembly
1-18 49484 Motor Spacer
1-19 49322 #10-24 x 1" (25,4mm) Hex Machine Screw
1-20 74146 Hex Nut #8-32 Eslok
1-21 89125 Screw #8-32 x ½" (12,7mm) Panhead
1-22 74150 Washer #8 Internal Tooth
1-23 74149 Hex Nut #8-32
1-24 74141 Screw #8-32 x 3/8" (9,5mm) RD HD PH
1-25 87087 Label, Caution Hot
1-26 14821 Bolt ¼-20 x ½" (12,7mm) Hex HD
1-27 74133 ¼-20 Hex Nut
1-28 47001 Pop Rivet
1-29 49331 Motor Plate

7
60 Special and P-60
ALL EXPORT MODELS #1866, #2085, #2086AND #2656
PARTS LIST - CABINET ASSEMBLY
Model Model
#2085JX #2086JX
Item No. Part No. Part No. Description
2-0 49155 49114 Complete Cabinet Assembly
2-1 22038 22038 Lead-In Cord
2-2 49440 49440 Heat Element 50 Watt
2-3 47328 47328 Glide Delrin Foot
2-4 47561 47561 Magnetic Catch
2-5 49020 49020 Door
2-6 76097 76097 Label, Unplug to Clean
2-7 49052 49052 Screw w/ Washer Taptite
2-8 49058 49058 Front Glass
2-9 49059 49059 Side Glass
2-10 49146 49146 Bottom Corn Pan
2-11 49091 49091 Wire Duct
2-12 49452 49453 Top Pan - O/S
2-13 49145 49145 Drop Panel
2-14 49157 49097 Bottom Pan
2-15 49100 49100 Old Maid Pan
2-16 49425 49425 Strip Heater Bracket
2-17 49104 49104 Cover, Corner Cover
2-18 49105 49105 Corner Cover
2-19 49464 49460 Right Rear Corner Post
2-20 49465 49461 Left Rear Corner Post
2-21 49467 49462 Left Front Corner Post
2-22 40068 49109 Side Extrusion
2-23 49004 49110 Front Extrusion
2-24 76026 76026 Strain Relief #SR-6P3-4
2-25 49158 77056 Decal, Front Glass
2-26 49123 49123 Crutch Tip
2-27 49466 49463 Right Front Corner Post
2-28 49138 49138 Left Female Hinge
2-29 49141 49141 Left Male Hinge
49139 49139 Right Female Hinge
49140 49140 Right Male Hinge
2-30 47702 47702 #8-32 Acorn Nut
2-31 74142 74142 #8-32 x ¼" Panhead Phillips
2-32 74141 74141 #8-32 x 3/8" Panhead Phillips
2-33 74149 74149 #8-32 Hex Nut
2-34 74150 74150 #8 Internal Tooth Washer
2-35 47663 47663 Label, 6 Steps to Pop
2-36 74141 74124 Screw #8-32 x 3/8" Brown
2-37 75267 75267 Tee Bolt
2-38 47120 47120 Knob

8
60 Special and P-60
ALL EXPORT MODELS #1866, #2085, #2086AND #2656
6 oz. KETTLE ASSEMBLY