GST DC-9204 User manual

30306359 Issue 1.04
Features
Alarming by pressing, reset by a special key.
Plug-in structure.
Designed to comply with EN 54-11.
Description
DC-9204 Innovation Manual Call Point (MCP) is
non-addressable. It alarms by the current caused by
pressing the action plate. It can be simply connected
to compatible conventional fire alarm system from
various manufacturers. This MCP is suitable for public
places.When there is fire, pressing the action plate on
this MCP can send alarm signal to compatible
conventional fire alarm control panel.
Connection and Cabling
Terminals on the MCP base are shown as Fig. 1.
I+ I- O+O-
60mm
Fig. 1
I+, I-: Input signal, connecting with compatible control
panel or the previous MCP.
O+, O-: Output signal, connecting with the next MCP.
Recommended Wiring
0.5mm2or above fire cable, subject to local codes.
Installation
The conduit can be surface mounted or flush
mounted.
Surface mounting:
First install the back box onto the wall using 4 screws,
then install the base onto the back box. Connect
cables to corresponding terminals as described above.
Hook the juts of the MCP body to the base, and then
press the part below the action plate to combine them
completely. Fig. 2 shows surfacemounting.
Flush mounting:
Install the base onto the back box. Then combine the
enclosure and base the same as surface mounting.
Fig. 3 shows flush mounting.
Back Box
Base
MCP Body
Fig. 2
Base MCP Body
Back Box
Fig. 3
Application
Application of the MCP is shown in Fig. 4.
Output-
Output+
Compatible Fire Alarm
Control Panel
Alarm Zone O-O+I-I+
To the next device
MCP
Fig. 4
0832-CPD-0789
548g/03
DC-9204
Innovation Manual Call Point

30306359 Issue 1.04
Usage of the key
Vertically insert the key into the key-hole, then push it
with force and turn it clockwise. Turn the key back and
pull it out when the action plate is rebounded.
Usage of the test tool
The test tool is used to keep continuity during
commissioning or maintenance when MCP is not
installed, so that cable test can be carried out easily
and make the circuit completed.
Limited Warranty
GST warrants that the product will be free of charge
for repairing or replacing from defects in design,
materials and workmanship during the warranty period.
This warranty doesn’t cover any product that is found
to have been improperly installed or used in any way
not in accordance with the instructions supplied with
the product. Anybody, including the agents,
distributors or employees, is not in the position to
amend the contents of this warranty. Please contact
your local distributor for products not covered by this
warranty.
Specification
Operating Voltage
24VDC (12VDC ～28VDC)
Standby Current
0mA
Alarm Current
≤30mA(equivalent
resistance is 470/1W)
Indicator
Red. Illuminates after
alarming.
Type of Initiating
Part
Reusable
Initiating Mode
Pressing the action plate
manually
Resuming Mode
Manually resumed by a
special key
Wiring
two-wire
Class
Type A, indoor use
Ingress Protection
Rating
IP43
Ambient
Temperature
-10℃～+55℃
Relative Humidity
≤95%, non-condensing
Material of
Enclosure
ABS
Dimensions
(L×W×H)
87.1mm×87.1mm×58mm
(with back box)
87.1mm×87.1mm×23mm
(without back box)
Mounting Hole
Distance
60mm
Weight
About 160g (with back box)
About 107g (without back
box)
This Data Sheet is subject to change without notice. Please contact GST for more information or questions.
Gulf Security Technology Co., Ltd.
No. 80, Changjiang East Road, QETDZ, Qinhuangdao, Hebei, P. R. China 066004
Tel: [phone] Fax: [phone]
service.gs[email protected]tc.com www.gst.com.cn