GST DI-9204E Owner's manual

This document is subject to change without notice. Please contact GST for more information or questions.
Gulf Security Technology Co., Ltd.
No. 80,Changjiang East Road, QETDZ, Qinhuangdao, Hebei, P. R. China 066004
www.gst.com.cn www.utcfireandsecurity.com [e-mail]
DS1054854-1 Page 1
Connecting to the loop of GST fire alarm system,
DI-9204E Digital Manual Call Point (the MCP) is
suitable for public places. When there is fire,
pressing the action plate on the MCP can send
the alarm signal to fire alarm control panel. After
receiving the signal, the control panel will show
address information of the MCP and generate
alarm sound.
Features
Electronically addressed by programmer
Non-break-glass. Reset by a special key.
Plug-in structure.
Designed to comply with EN 54-11.
LPCB/CPD approved.
Wiring
Terminals on the MCP are shown as Fig. 1
Z1, Z2: Connecting to the loop of control panel,
polarity-insensitive.
Recommended Cabling
1.0mm2 or above fire cable, subject to local
codes.
Z1 Z2 Z1 Z2
Fig. 1
DI-9204E
Digital Manual Call Point
Application
1. Application of the MCP is shown in Fig. 2
Z2
Z1
Fire Alarm
Control Panel
MCP
to the next device
Z1 Z2 Z1 Z2
Fig. 2
2. The MCP should be programmed using
P-9910B programmer, shows in Fig.3. Please
refer to P-9910B Hand Held Programmer
Installation and Operation Manual.


Z2Z1 Z2Z1
Fig. 3
3. Usage of the key for reset
Vertically insert the key into the key-hole, push
in and turn clockwise. Turn the key back and
pull it out when the glass is rebounded, as
shown in Fig.4.

This document is subject to change without notice. Please contact GST for more information or questions.
Gulf Security Technology Co., Ltd.
No. 80,Changjiang East Road, QETDZ, Qinhuangdao, Hebei, P. R. China 066004
www.gst.com.cn www.utcfireandsecurity.com [e-mail]
DS1054854-1 Page 2
60
1
2
Fig.4
4. Usage of the key for unlocking
Insert the forked key and push in hardly, the
MCP body will be separated from the base or
the back box, as shown in Fig.5.
Fig.5
5. Usage of the test tool
The test tool is used to keep the continuity of
the loop during commissioning or maintenance
when MCP is not installed, so that cable test
can be carried out easily and make the circuit
completed.
6. Compatible Equipment
This MCP can be used together with control
panels such as GST100, GST200-2, GST5000
and GST-IFP8.
Specification
Operating Voltage
Loop 24V (16V～28V)
Standby Current
≤0.6mA
Alarm Current
≤1.8mA
Type of Initiating
Part
Reusable
Initiating Mode
Pressing the action plate manually
Resuming Mode
Manually resumed by a special key
Programming
Mode
Electronically addressed
Code Range
One address within 1～242
Wiring
Two-wire, polarity-insensitive
Class
TypeA, indoor use
Ingress Protection
Rating
IP43
Ambient
Temperature
-10℃～+55℃
Relative Humidity
≤95%, non condensing
Material of
Enclosure
ABS
Dimension
(L×W×H)
87.1mm×87.1mm×58mm (with
back box)
87.1mm×87.1mm×23mm (without
back box)
Mounting Hole
Distance
60mm
Weight
About 160g (with back box)
About 107g (without back box)
Accessories and Tools
Model
Name
Remark
P-9910B
Hand Held Programmer
Order separately
Back box 1 piece
within same
package
Test tool 1 piece
within same
package
Reset key 1 piece
within same
package
Please contact with GSTsales for compatible devices.