GST DI-9204E User manual

30309264Issue 1.03
Features
Electronically addressed. The address can be
modified in field.
Alarm by pressing, reset by a special key.
Plug-in structure.
Standard: EN 54-11.
Description
Connecting to the loop of GST fire alarm system,
DI-9204E Digital Manual Call Point (MCP) is suitable
for public places. When there is a fire, pressing the
frangible element on this MCP can send fire signal to
fire alarm control panel. After receiving the signal, the
control panel will show address information of the
MCP and generate alarm sound.
Connection and Cabling
Terminals on the MCP base are shown as Fig. 1（unit:
mm）.
Z1 Z2 Z1 Z2
Fig. 1
Z1, Z2: Connecting with loop of the control panel,
polarity-insensitive.
Recommended Cabling
0.5mm2or above fire cable, subject to local codes.
Installation
The MCP can be mounted in two ways: conduit
embedded and surface mounting.
Surface Mounting: First install the back box into the
wall using 4 screws, and then install the base onto the
back box. Connect cables to corresponding terminals
as described above. Hook the juts of the MCP body to
the base, and then press the part below the frangible
element to combine them completely, and then screw
the lock screw as shown in Fig. 2.
Conduit Embedded: First install the base onto the
back box, then connect the MCP body and the base
followed instructions above, then screw the lock screw
as shown in Fig. 3.
Back Box
Base
MCP Body
Lock Screw
Fig. 2
DI-9204E
Digital Manual Call Point
548g/08
0832-CPR-F0130
GST-0011-01
13

30309264Issue 1.03
Base MCP Body
Embedded Box
Lock Screw
Fig. 3
Application
The MCP should be programmed using P-9910B
programmer. Please refer to P-9910B Hand Held
Programmer Installation and Operation Manual.
Z1 and Z2 are to be connected with the loop of
fire alarm control panel. If it’s correct, the FACP
can register the MCP.
Usage of the key
Vertically insert the key into the key-hole, and
turn it clockwise, then push it with force. Turn the
key back and pull it out when the frangible
element is rebounded.
Compatible equipment
It can be used with GST control panels such as
GST200, GST200-2, GST200N,GST-IFP8.
Accessories and Tools
Model
Name
Remarks
P-9910B
Handheld
Programmer
Order
separately
WEEE Information
2012/19/EU (WEEE directive):
Products marked with this symbol cannot
be disposed of as unsorted municipal
waste in the European Union. For proper
recycling, return this product to your local
supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points.
Specification
Operating Voltage
Loop 24V（16V～28V）
Standby Current
≤0.6mA
Alarm Current
≤1.8mA
Indicator
Red. Flashes every 3s normally.
Illuminates after alarming.
Type of Initiating
Part
Reusable
Initiating Mode
Pressing the frangible element
manually
Resuming Mode
Manually resumed by a special
key
Programming
Mode
Electronically addressed
Address Range
One address within 1～242.
Wiring
Polarity-insensitive two-wire
Class
Type A, indoors.
Ingress Protection
Rating
IP43
Environmental
Temperature
-10℃～+55℃
Relative Humidity
≤95%, non condensing
Material of
Enclosure
ABS, red
Dimension
(L×W×H)
87.1mm×87.1mm×58.5mm (with
back box)
87.1mm×87.1mm×23.5mm
(without back box)
Mounting Hole
Distance
60mm
Weight
About 160g (with back box)
About 107g (without back box)
Limited Warranty
GST warrants that the product will be free from defects
in design, materials and workmanship during the
warranty period. This warranty shall not apply to any
product that is found to have been improperly installed
or used in any way not in accordance with the
instructions supplied with the product. Anybody,
including the agents, distributors or employees, is not
in the position to amend the contents of this warranty.
Please contact your local distributor for products not
covered by this warranty.
This Data Sheet is subject to change without notice. Please contact GST for more information or questions.
Gulf Security Technology Co., Ltd.
No. 80, Changjiang East Road, QETDZ, Qinhuangdao, Hebei, P. R. China 066004
Tel: [phone] Fax: [phone]
[e-mail] www.gst.com.cn