Hachette ALIEN PACK 8 Manual

spectacular
1:2
scale
ALIEN
BUILD THE
TERRIFYING
XENOMORPH
FROM
ALIEN
EASYEASY
ASSEMBLYASSEMBLY
PACK 8
KITS 53 - 60
Non contractual visual

Hachette Partworks Ltd, 4th Floor, Jordan House,
47 Brunswick Place, London N1 6EB
www.hachettepartworks.com
©2023/2024 Hachette Partworks Ltd.
©2023 20th Century Studios.
ALL RIGHTS RESERVED
All parts belong to a kit. Collectors item for adults.
Not suitable for children under 14.
PACK 8 | BUILD INSTRUCTIONS
ALIEN
WARNING: Some parts are assembled using magnets. These magnets can cause serious
injury if they are swallowed. Keep away from children. If you suspect a magnet has been
swallowed, seek medical help straight away.
Some parts may have sharp edges, please handle them with care.
The installation of electronic parts must always be carried out by an adult. When replacing batteries,
use the same type of batteries.
Please ensure that the battery compartment is securely fastened before you use the model.
Used batteries should be recycled.
Please make sure to check with your local council how batteries should be disposed of in your area.
Batteries can present a choking danger to small children and may cause serious harm if ingested. Do
not leave them lying around and keep any spare batteries locked away at all times.
KIT 53
THE LEFT HAND (II)
KIT 54
THE LEFT HAND (III)
KIT 55
THE LEFT RADIUS
KIT 56
THE RADIUS &
THE HUMERUS
STEPS & TIPS ONLINE
KIT 57
THE LEFT HUMERUS
KIT 58
THE LEFT HUMERUS (II)
KIT 59
THE LEFT HUMERUS (III)
KIT 60
THE LEFT ARM (I)

PB 1
ASSEMBLY GUIDE
In this kit you will continue to build the left hand.
KIT 53:THE LEFT HAND (II)
53-1
53-3 53-4 53-5 53-6
53-7 53-8
53-2
PARTS SUPPLIED
Ref. Name Qty.
53-1 Left Radius Skin 1
53-2 Left Hand 1
53-3 Left Finger L4 1
53-4 Left Finger L5 1
Ref. Name Qty.
53-5 Left Finger L6 1
53-6 Connector 1
53-7 Magnets 6
53-8 2.3x6mm screws (1 spare) 4

23
KIT 53: THE LEFT HAND (II)
1
53-1
53-7
53-7
53-7
53-7
53-7
53-7
Glue six magnets 53-7 into the
circular recesses inside the Left
Radius Skin 53-1. It doesn’t matter
which way round the magnets are
tted.

23
KIT 53: THE LEFT HAND (II)
2
3
53-4 (L5)
53-3
(L4)
53-5
(L6)
53-2
53-2
After checking the fit of Left
Finger L5 53-4 on the back
of the Left Hand 53-2, glue
in place.
Repeat the previous step
to add Fingers L4 53-3
and L6 53-5. As before,
glue in place.

4PB
KIT 53 IS COMPLETE
4
53-8
52-1
52-5
53-2
MAGNETS HAVE BEEN FIXED TO
THE RADIUS SKIN AND WORK HAS
CONTINUED ON THE LEFT HAND.
Take the Left Hand 52-1 which was
assembled in pack 7 - kit 52. Fit the
free side of the Connector 52-5
over the raised screw socket on the
back of Hand 53-2 and x in place
with a 2.3x6mm screw 53-8. Whilst
doing this, it may help to temporarily
loosen the previously tted screw.
!Keep the screws and connector in a safe place until they are needed in the next kit.
KIT 53: THE LEFT HAND (II)

PB 1
ASSEMBLY GUIDE
In this kit you will continue to work on the left hand and left radius.
KIT 54: THE LEFT HAND (III)
PARTS SUPPLIED
Ref. Name Qty.
54-1 Left Radius 1
54-2 Left-hand Palm 1
54-3 Wrist Joint 1
54-4 Bracket 1
54-5 Pipe A1 1
Ref. Name Qty.
54-6 Pipe A2 1
54-7 Pin 1
54-8 Magnets 6
54-9 2.3x6mm screws (1 spare) 3
54-1
54-3
54-7 54-8 54-9
54-4 54-5 54-6
54-2

2
1
2
3
54-6 (A2)
54-5
(A1)
53-1
54-1
53-1
54-8
54-1
53-1
54-8
Take the left radius skin 53-1 from
the previous kit. After test-fitting,
glue Pipes A2 54-6 and A1 54-5
into the slots at the side, as shown.
Note the locating peg at one end of
each of the Pipes.
Fit six Magnets 54-8 into the
circular recesses on the inside
of the Left Radius 54-1. Before
glueing in place, make sure that
they are correctly orientated so
that they are attracted to the
corresponding magnets in the skin
53-1 below.
Turn the skin 53-1
over and fit the
Left Radius 54-1
inside.
KIT 54: THE LEFT HAND (III)

3
KIT 54: THE LEFT HAND (III)
4
5
54-3
54-7
54-9
54-4
54-3
54-7
53-2
52-1
54-9
Take the left hand assembly
from the previous kit and fit the
Wrist Joint 54-3 into the slot in
the hand formed by parts 52-1
and 53-2. The ends of the Pin
54-7 should rest in recesses on
the hand parts 52-1 and 53-2.
Orientate the Bracket 54-4, as
shown and fit the screw holes over
the raised screw sockets on parts
52-1 and 52-3. When sure of a
good fit, secure in place with two
2.3x6mm screws 54-9.
Insert the Pin 54-7
into the central
hole in the Wrist
Joint 54-3.

KIT 54 IS COMPLETE
67
53-2
52-1
53-8
53-6
53-2
52-1
53-8
54-2
Magnets have been added to
the radius and the left hand
has been completed.
Test-t the pegs on the underside
of the Left-hand Palm 54-2 into
the remaining holes in the hand
assembly 52-1/53-2. When
certain of a good t, glue in place.
The connector 53-6, supplied with
the previous kit, is tted across parts
52-1 and 53-2, as shown. Using
two of the 2.3x6mm screws 53-8,
again supplied with the previous kit,
x the connector 53-6 in place.
KIT 54: THE LEFT HAND (III)
4