Hachette ALIEN spectacular Product information sheet

spectacular
1:2
scale
ALIEN
BUILD THE
TERRIFYING
XENOMORPH
FROM
ALIEN
EASY
ASSEMBLY
PACK 5
KITS 29 - 36
Non contractual visual

Hachette Partworks Ltd, 4 t h F l o o r , J o r d a n H o u s e ,
47 Brunswick Place, London N1 6EB
www.hachettepartworks.com
© 2023/2024 Hachette Partworks Ltd.
© 2023 20th Century Studios.
ALL RIGHTS RESERVED
All parts belong to a kit. Collectors item for adults.
Not suitable for children under 14.
PACK 5 | BUILD INSTRUCTIONS
ALIEN
WARNING: Some parts are assembled using magnets. These magnets can cause serious
injury if they are swallowed. Keep away from children. If you suspect a magnet has been
swallowed, seek medical help straight away.
Some parts may have sharp edges, please handle them with care.
The installation of electronic parts must always be carried out by an adult. When replacing batteries,
use the same type of batteries.
Please ensure that the battery compartment is securely fastened before you use the model.
Used batteries should be recycled.
Please make sure to check with your local council how batteries should be disposed of in your area.
Batteries can present a choking danger to small children and may cause serious harm if ingested. Do
not leave them lying around and keep any spare batteries locked away at all times.
KIT 29
THE RIGHT RIBS
AND THE RIGHT THIGH (I)
KIT 30
THE RIGHT RIBS
AND THE RIGHT THIGH (II)
KIT 31
THE RIGHT THIGH
KIT 32
THE LEFT RIBS AND
THE RIGHT FEMUR (I)
KIT 33
THE LEFT RIBS AND
THE RIGHT FEMUR (II)
STEPS & TIPS ONLINE
KIT 34
THE LEFT RIBS AND
THE RIGHT FEMUR (III)
KIT 35
THE LEFT RIBS AND
THE RIGHT FEMUR (IV)
KIT 36
THE LEFT RIBS AND
THE RIGHT THIGH (I)

11
ASSEMBLY GUIDE
In this kit you will continue to work on the Xenomorph’s right ribs and begin
assembly of the right thigh and its attachments.
KIT 29:THE RIGHT RIBS
AND THE RIGHT THIGH (I)
29-1 29-2
29-3 29-4 29-5 29-6
PARTS SUPPLIED
Ref. Name Qty.
29 -1 Right Rib 1
29 -2 Right Thigh O u ter Skin 1
29 -3 P ipe B 1 (right thigh) 1
Ref. Name Qty.
29 -4 P ipe B 2 (right thigh) 1
29 -5 Magnets 4
29 -6 2.3x6mm screws (1 spare) 2

2
2
3
Take the rib support assembly
19-3 from the previous kit. Fit
the raised screw socket on the
Rib 29-1 into the hole next to Rib
27-2. Fix in place with a 2.3x6mm
screw 29-6. Put the assembly
aside until the next kit.
Take the Outer Skin 29-2 and
test-fit the Pipe B1 29-3 into
the slots, as shown. There is
also a peg at one end which fits
into a corresponding hole. When
sure of a good fit, glue firmly in
place. Remember to remove the
label on the pipe before fitting.
Test fit the tabs on Pipe
B2 29-4 in the slots on
Skin 29-2, which continue
along from pipe 29-3.
Again, there is a peg at
one end which fits into a
corresponding hole. After
checking the fit, glue firmly
in place.
1
29-3 (B1)
29-4 (B2)
29-2
29-3
29-2
29-6
19-3
27-2
29-1
KIT 29: THE RIGHT RIBS AND THE RIGHT THIGH (I)

3
KIT 29: THE RIGHT RIBS AND THE RIGHT THIGH (I)
KIT 29 IS COMPLETE
Study the diagram carefully and
note the position of the four
Magnets 29-5. Glue the Magnets
29-5 into the circular recesses on
the inside of the Outer Skin 29-2.
It doesn’t matter which way round
the magnets are fitted.
4
29-5
29-5
29-2
ANOTHER RIB HAS BEEN ADDED TO
THE FRAME AND WORK HAS BEGUN
ON THE RIGHT THIGH.

11
ASSEMBLY GUIDE
In this kit you will continue to work on the Xenomorph’s right ribs and thigh.
KIT 30:THE RIGHT RIBS
AND THE RIGHT THIGH (II)
30-1
30-2
30-3 30-4
30-630-5
PARTS SUPPLIED
Ref. Name Qty.
30 -1 Right Rib 1
30 -2 P ipe (right thigh) B 3 1
30 -3 P ipe (right thigh) B 4 1
Ref. Name Qty.
30 -4 P ipe (right thigh) B 5 1
30 -5 Magnets 4
30 -6 2.3x6mm screws (1 spare) 2

22
KIT 30: THE RIGHT RIBS AND THE RIGHT THIGH (II)
1
30-6
19-3
29-1
30-1
Take the rib assembly 19-3 from
the previous kit and fit the raised
screw socket on Rib 30-1 into the
remaining hole. Fix in place with
a 2.3x6mm screw 30-6. Keep the
assembly safely aside.

33
KIT 30: THE RIGHT RIBS AND THE RIGHT THIGH (II)
2
34
30-2 (B3)
30-3 (B4) 30-4 (B5)
29-2
30-3
29-2
29-2
Repeat the previous step to fit
Pipe B4 30-3 onto the Thigh
Outer Skin 29-2. Note that this
pipe is fitted to the middle of
the skin and there is a peg at
each end.
Next, take the Thigh Outer Skin
29-2 which was worked on in the
last kit. The line of pipes continues
with the fitting of Pipe B3 30-2.
After test-fitting the Pipe 30-2,
as shown, apply a little glue to the
tabs and hold firmly in place until
the glue sets.
Pipe B5 30-4 fits next to Pipe
30-3, as shown. Check the fit of
Pipe B5 30-4 on the outer skin
29-2 and glue firmly in place.
Note that there is a peg at one end
of the pipe. Allow the glue to dry
before continuing.

44
KIT 30 IS COMPLETE
5
30-5
30-5
29-2
A RIB AND MORE PIPES HAVE
BEEN FITTED AS WELL AS
FURTHER MAGNETS.
KIT 30: THE RIGHT RIBS AND THE RIGHT THIGH (II)
Turn the outer skin 29-2 over and
glue four Magnets 30-5 into the
remaing four circular recesses. It
doesn’t matter which way round
the magnets are fitted.

11
ASSEMBLY GUIDE
In this kit you will continue to assemble the component
parts of the Xenomorph’s right thigh.
KIT 31:THE RIGHT THIGH
31-1
31-5 31-6
31-2 31-3 31-4
PARTS SUPPLIED
Ref. Name Qty.
31-1 P ipe (right thigh) B 6 1
31-2 P ipe (right thigh) B 7 1
31-3 Skin D etail (right thigh) C 1 1
Ref. Name Qty.
31-4 Skin D etail (right thigh) C 2 1
31-5 Skin D etail (right thigh) C 3 1
31-6 Magnets 8