Hachette ALIEN spectacular User manual

spectacular
1:2
scale
ALIEN
BUILD THE
TERRIFYING
XENOMORPH
FROM
ALIEN
EASYEASY
ASSEMBLYASSEMBLY
PACK 10
KITS 69 - 76
Non contractual visual

Hachette Partworks Ltd, 4th Floor, Jordan House,
47 Brunswick Place, London N1 6EB
www.hachettepartworks.com
©2023/2024 Hachette Partworks Ltd.
©2023 20th Century Studios.
ALL RIGHTS RESERVED
All parts belong to a kit. Collectors item for adults.
Not suitable for children under 14.
PACK 10 | BUILD INSTRUCTIONS
ALIEN
WARNING: Some parts are assembled using magnets. These magnets can cause serious
injury if they are swallowed. Keep away from children. If you suspect a magnet has been
swallowed, seek medical help straight away.
Some parts may have sharp edges, please handle them with care.
The installation of electronic parts must always be carried out by an adult. When replacing batteries,
use the same type of batteries.
Please ensure that the battery compartment is securely fastened before you use the model.
Used batteries should be recycled.
Please make sure to check with your local council how batteries should be disposed of in your area.
Batteries can present a choking danger to small children and may cause serious harm if ingested. Do
not leave them lying around and keep any spare batteries locked away at all times.
KIT 69
THE LEFT LEG (VIII)
KIT 70
THE LEFT LEG (IX)
KIT 71
THE LEFT LEG (X)
KIT 72
THE LEFT LEG (XI)
STEPS & TIPS ONLINE
KIT 73
THE LEFT LEG (XII)
KIT 74
THE LEFT LEG AND
THE ABDOMEN
KIT 75
THE ABDOMEN (I)
KIT 76
THE ABDOMEN (II)

PB
1
ASSEMBLY GUIDE
In this kit you will continue to work on parts of the Xenomorph’s left leg.
KIT 69: THE LEFT LEG
(VIII)
PARTS SUPPLIED
Ref Name Qty
69-1 Left Femur 7 1
69-2 Left Femur 8 1
69-3 Thigh Skin Appendage B3 1
69-4 Thigh Skin Appendage B4 1
69-5 Thigh Skin Appendage B5 1
Ref Name Qty
69-6 Pipe B6 1
69-7 Pipe B7 1
69-8 Connector 4
69-9 Magnets 8
69-10 2.3x6mm screws (1 spare) 9
69-1
69-3 69-4 69-5 69-6
69-9 69-10
69-7 69-8
69-2

2
3
KIT 69: THE LEFT LEG (VIII)
1
3
2
69-2
69-8
69-2
69-1
68-1
68-2
68-3
69-8
69-10
69-10
69-1
Align Femur 69-1 next to
Femur 69-2, as shown.
Join the two sections of
the Femur 69-1 and
69-2 together using
two Connectors 69-8.
Fit the connectors over
the raised screw sockets
inside the oval recesses
and secure in place with
four 2.3x6mm screws
69-10.
Take the femur assembly
68-1/68-2 which was
worked on in the pack
9 - kit 68, and remove the
Skin 68-3.

2
3
3
KIT 69: THE LEFT LEG (VIII)
5
6
4
69-1
69-2
68-2
68-1
69-10
69-10 69-9
69-9
69-9
69-9
69-8
69-8
69-1
68-1
69-2
68-3
Line up the two femur
assemblies 69-1/69-
2 and 68-1/68-2
ready to join them
together in the next
step.
Fit the remaining two Connectors
69-8 into the oval recesses which
bridge the join between assemblies
69-1/69-2 and 68-1/68-2. Fix
in place with four 2.3x6mm screws
69-10 and put the assembly aside
until it is needed in step 7.
Take the Skin 68-3 and glue
four Magnets 69-9 into the
remaining circular recesses.
It doesn’t matter which way
up they are fitted.

4
5
KIT 69: THE LEFT LEG (VIII)
8
7
69-1
69-2
68-2
68-3
69-969-9
69-2 69-1
68-1
After the Magnets 69-9
have set rmly in place,
t the femur assembly
68-1/68-2/69-1/69-2
inside the Skin 68-3.
The remaining four Magnets 69-
9, from this pack are fitted into
the recesses in the femur parts
69-1 and 69-2. They need to be
orientated so that they are attracted
to the magnets in the skin below.
Once certain of a good fit, glue the
Magnets 69-9 in place and put the
assembly safely aside.

4
5
KIT 69: THE LEFT LEG (VIII)
10
9
67-1
66-1
69-6 (B6)
69-7 (B7)
66-1
67-2
66-2
66-3
Take the skin 66-1 and femur
assembly 66-2/66-3/67-1/67-2
which was worked on in pack 9 - kit
67 and remove the skin 66-1.
Turn the skin
66-1 over and
note the position of
the two recesses shown above in
green. Test-fit Pipe B7 69-7 into
one recess and Pipe B6 69-6 in
the other, as shown. After checking
the fit, glue the pipes in place.

6
PB
KIT 69 IS COMPLETE
11
69-3 (B3)
69-4 (B4)
69-5 (B5)
66-1
Work has continued on the left leg with
femur sections being joined together and
magnets added to the skin.
Finally, the Skin Appendages
B3 69-3, B4 69-4 and B5
69-5 are test-tted onto the
Thigh Skin 66-1, as shown.
They have different shaped
recesses to ensure they t on
the correct peg. When you
are sure of a good t, glue in
place.
KIT 69: THE LEFT LEG (VIII)

PB
1
ASSEMBLY GUIDE
In this kit you will start to build parts of the left pelvis.
KIT 70: THE LEFT
LEG (IX)
70-1 70-2 70-3
70-670-570-4
70-7 70-8 70-9 70-10
PARTS SUPPLIED
Ref Name Qty
70-1 Pelvis Joint 1 1
70-2 Pelvis Joint 2 1
70-3 Ball Joint 1
70-4 Grip 1
70-5 Socket Liner 2
Ref Name Qty
70-6 Pipe A4 1
70-7 Pipe A5 1
70-8 3x22mm screws (1 spare) 3
70-9 Nut 3
70-10 2.3x6mm screws (1 spare) 5

2
3
KIT 70: THE LEFT LEG (IX)
1
70-5
70-2
2
70-5
70-1
Fit the two pegs on one of
the Socket Liners 70-5 into
the holes in the Pelvis Joint
70-2.
Repeat the previous step to t
the other Socket Liner 70-5
into the holes in the Pelvis
Joint 70-1.