Hantek Tablet1000 Series User manual

Tablet1000 series
Tablet oscilloscope
Quick Guide
2022.05

Warranties and Declarations
Copyright
The copyright of this document belongs to Qingdao Hantek Electronics Co., LTD.
Statement
Qingdao Hantek Electronics Co., Ltd. reserves the right to amend this document without prior notice.
Qingdao Hantek Electronics Co., Ltd. promises that the information provided is correct and reliable but
does not guarantee that this document is free from errors. Before using this product, please make sure
that the specifications of relevant technical documents are the latest effective version. If you use
documents or products of Qingdao Hantek Electronics Co., LTD and need products, patents or works
of third parties to cooperate with them, you shall be responsible for obtaining the consent and
authorization of the third parties. The above consent and authorization shall not be the liability of
Hantek.
Product certification
Hantek certified Tablet1000 series oscilloscope to meet China's national industry standards and has
passed the CE certification.
Contact us
If you have any questions when using the products of Qingdao Hantek Electronics Co., LTD., you can
obtain service and support through the following ways:
Email: [e-mail], supp[email protected]
Website: http://www.hantek.com

Safety requirements
EN
Copyright © Qingdao Hantek Electronics Co., LTD Tablet1000 Quick guide 1
1 Safety requirements
1.1 Summary of general safety matters
Read the following safety precautions carefully to avoid injury and to prevent damage to
this product or any product connected. To avoid possible dangers, please use this
product in accordance with the regulations.
⚫Only professionally authorized personnel can perform repairs.
⚫Use the right power cable.
Use the power cable approved by the country in which the product is used only.
⚫Connect and disconnect correctly.
Before connecting the probe to the circuit being measured, please connect the
probe to the oscilloscope first. Before disconnecting the probe from the oscilloscope,
please disconnect the probe and the circuit under test first.
⚫Ground the product.
To avoid electric shocks, the product is grounded through a grounding conductor of
the power cable. The grounding conductor must be connected to the ground before
connecting the input or output terminals of the product. Ensure that the product is
properly grounded.
⚫Connect the probe properly.
The ground wire of the probe is the same as the ground potential. Do not connect
the ground wire to high voltage.
⚫View all terminal rating values.
To avoid fire or excessive current, please check all rating values and signs on the
product. Please consult the product manual for details of the rating values before
connecting the product.
⚫Do not operate with the cover open.
Do not run the product with the cover or panel open.
⚫Avoid circuit exposure.
Do not touch exposed connectors and components after power is switched on.
⚫Do not operate if the product is suspected to be faulty.
If you suspect that the product has been damaged, please ask qualified
maintenance personnel to check it.

Safety requirements
EN
Tablet1000 Quick guide Copyright © Qingdao Hantek Electronics Co., LTD
2
⚫Maintain proper ventilation.
⚫Do not operate in a humid environment.
⚫Do not operate in inflammable or explosive environment.
⚫Please keep the product surface clean and dry.
Warning:
Equipment that meets Class A requirements may not provide adequate protection
for broadcast services in residential environments.
1.2 Security terms and signs
Security terms in this manual:
Warning:
Indicates that the operation may not cause immediate damage to you.
Note:
Indicates that the operation may cause damage to the product or other property.
Safety terms on products:
Warning:
Indicates a potential hazard may be caused to you if you do not perform this
operation.
Safety signs on the product:
1.3 Measurement category
Measurement category

Safety requirements
EN
Copyright © Qingdao Hantek Electronics Co., LTD Tablet1000 Quick guide 3
This instrument can be used for measurement under class I.
Warning:
This instrument is only allowed to be used in the specified measurement class.
Measurement class definition
⚫Class I refers to measurements taken on a circuit not directly connected to
the main power supply. For example, measurements made on circuits that are not
exported from a main power supply, especially from a protected (internal) main
power supply. In the latter case, the instantaneous stress will change. Therefore,
the user should understand the instantaneous capacity of the instrument.
⚫Class II refers to measurements taken on a circuit directly connected to
low-voltage instruments. For example, measurements made on household
appliances, portable tools, and similar equipment.
⚫Class III refers to measurements taken on construction equipment. For
example, measurements made on switchboards, circuit breakers, circuits (including
cables, busbars, junction boxes, switches, sockets) in fixed equipment, as well as
equipment for industrial use and certain other equipment (for example, fixed motors
permanently connected to fixed instruments).
⚫Class IV refers to measurements taken at the source of low-voltage
equipment. For example, measurements made on electricity meters, primary
overcurrent protection equipment, and pulse control units.
1.4 Working conditions
Temperature
Operating temperature: 0°C -50°C
Storage temperature: -20°C -70°C
Humidity
≤+104℉(≤+40°C): Rh≤90%
106℉to 122℉(+41°C to 50°C ): Humidity≤60%
Warning:
To avoid short circuit or electric shock, do not operate the instrument in a humid
environment.
Altitude
Operating and not operating: 3,000m (10,000 ft).
Random vibration: 0.31g RMS at 50Hz to 500Hz, 10 minutes per axial direction.
Not operating: 2.46g RMS from 5Hz to 500Hz, 10 minutes per axial direction.

Safety requirements
EN
Tablet1000 Quick guide Copyright © Qingdao Hantek Electronics Co., LTD
4
Installation (Overvoltage) Class This product is powered by a main power supply
conforming to Installation (overvoltage) Class II.
Warning:
Ensure that no overvoltage (such as voltage caused by lightning) reaches the
product. Otherwise, the operator may suffer electric shocks.
Installation (overvoltage) class definition
Class I refers to the signal level, which is applicable to the measuring terminal of the
instrument connected to the source circuit. Measures have been taken to limit the
instantaneous voltage to the corresponding low level.
Class II refers to the local distribution level, which is applicable to instruments connected
to the mains (AC) supply.
Pollution level
Level 2
Pollution level definition
⚫Level 1: No pollution, or only dry non-conductive pollution. This pollution level has
no impact. For example: clean room or air-conditioned office environment.
⚫Level 2: Generally, only dry non-conductive pollution. Temporary conduction due to
condensation may sometimes occur. For example: general indoor environment.
⚫Level 3: Conductive pollution, or dry non-conductive pollution becoming conductive
due to condensation. For example, an outdoor environment with a canopy.
⚫Level 4: Permanent conductive pollution through conductive dust, rain, or snow.
For example: outdoor places.
Security level
Level 1 - Grounded products
1.5 Maintenance and cleaning
Maintenance:
Do not make the LCD exposed to direct sunlight for a long time when placing the
oscilloscope.
Cleaning:
Regularly check the oscilloscope and probe according to the requirements of the
operating conditions, please follow the following steps to clean the outer surface of the
instrument:
1) Using a lint-free cloth to remove the dust from the outside of the oscilloscope and

Safety requirements
EN
Copyright © Qingdao Hantek Electronics Co., LTD Tablet1000 Quick guide 5
probe. Please be careful to avoid scratching the smooth display filter material.
2) Using a soft cloth soaked with water to clean the oscilloscope. For more thoroughly
clean, use 75% isopropyl alcohol aqueous solvent
Note:
To avoid damage to the oscilloscope or the surface of the probe, please do not
use any corrosive reagent or chemical cleaning reagent.
Warning:
Before repowering, please make sure the instrument is completely dry, to avoid
electrical short circuit or even personal injury caused by moisture.
1.6 Environmental precautions
The following sign indicates that this product conforms to the requirements set out by the
WEEE Directive 2002/96/EC.
Equipment recycling:
Producing the instrument requires the extraction and use of natural resources. Some
substances contained in the instrument may be harmful to the environment or human
health if the product is not disposed of properly. To avoid the release of harmful
substances into the environment and reduce the use of natural resources, it is
recommended that appropriate methods be used to recycle this product to ensure that
most of the materials can be correctly reused.

Document overview
EN
Tablet1000 Quick guide Copyright © Qingdao Hantek Electronics Co., LTD
6
2 Document overview
This document is used to guide the user to quickly understand the front and back panels,
user interfaces, and basic operation methods of the Tablet1000 series digital
oscilloscopes.
Tip:
The latest version of this manual can be downloaded at (http://www.hantek.com).
Document number:
202205
Software version:
Software upgrade may change or increase product functionalities, please pay attention
to Hantek website for the latest version.
Document format conventions:
1 Virtual keys and main interface icons
Use [name] to represent virtual keys and main interface icons. For example, [HOME] is
for , [OSC]is for .
2 Menu
Use "menu text (bold) + color" to represent a label or a menu option. For example, Basic
Settings means to click the "Basic Settings" option on the current operation interface to
enter the function configuration menu of "Basic Settings".
3 Operation steps
Use ">" to represent the next step. For example, Utility>Acquire means click Utility
label before clicking Acquire menu.
Document content conventions:
Tablet1000 series tablet oscilloscope consists of the following models. Unless otherwise
specified, this manual uses TO1254D as an example to describe the Tablet1000 series
and basic operations.
Model
Channel
Bandwidth
Sampling rate
Signal source
Multimeter
TO1112
2
110MHz
250MSa/S
-
-
TO1112C
2
110MHz
250MSa/S
-
Yes
TO1112D
2
110MHz
250MSa/S
25MHz
Yes

Document overview
EN
Copyright © Qingdao Hantek Electronics Co., LTD Tablet1000 Quick guide 7
Model
Channel
Bandwidth
Sampling rate
Signal source
Multimeter
TO1152
2
150MHz
1GSa/S
-
-
TO1202
2
200MHz
1GSa/S
-
-
TO1252
2
250MHz
1GSa/S
-
-
TO1152C
2
150MHz
1GSa/S
-
Yes
TO1202C
2
200MHz
1GSa/S
-
Yes
TO1252C
2
250MHz
1GSa/S
-
Yes
TO1152D
2
150MHz
1GSa/S
25MHz
Yes
TO1202D
2
200MHz
1GSa/S
25MHz
Yes
TO1252D
2
250MHz
1GSa/S
25MHz
Yes
TO1154
4
150MHz
1GSa/S
-
-
TO1204
4
200MHz
1GSa/S
-
-
TO1254
4
250MHz
1GSa/S
-
-
TO1154C
4
150MHz
1GSa/S
-
Yes
TO1204C
4
200MHz
1GSa/S
-
Yes
TO1254C
4
250MHz
1GSa/S
-
Yes
TO1154D
4
150MHz
1GSa/S
25MHz
Yes
TO1204D
4
200MHz
1GSa/S
25MHz
Yes
TO1254D
4
250MHz
1GSa/S
25MHz
Yes
TO1154AUTO
4
150MHz
1GSa/S
25MHz
Yes
TO1204AUTO
4
200MHz
1GSa/S
25MHz
Yes

Document overview
EN
Tablet1000 Quick guide Copyright © Qingdao Hantek Electronics Co., LTD
8
Model
Channel
Bandwidth
Sampling rate
Signal source
Multimeter
TO1254AUTO
4
250MHz
1GSa/S
25MHz
Yes
Table 2.1 Model21