Hantek DPO6000 Series User manual

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
DPO6000,MPO6000 Series
Digital Phosphor Oscilloscope
V 1.1

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 1 -
Copyright Statement
Copyright
Qingdao Hantek Electronic Co.,Ltd.
Statement
Qingdao Hantek Electronic Co., Ltd. reserves the right to amend this document without
prior notice. Qingdao Hantek Electronic Co., Ltd. promises that the information provided is
correct and reliable, but does not guarantee that this document is infallible. Please make
sure that the specifications of relevant technical documents used are the latest and valid
version by yourself before using this product.If you require the cooperation of products,
patents or works of a third party when your company use the documents or products of
Qingdao Hantek Electronic Co., Ltd., your company shall be responsible for obtaining the
consent and authorization of the third party. The aforesaid consent and authorization is
not the responsibility of our company to guarantee.

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 2 -
Technical Support
If you have any question or ambiguity in the process of using products of Qingdao Hantek
Electronic Co., Ltd., you can get the service and support through the following ways:
A: Please contact the local distributor of Qingdao Hantek Electronic Co., Ltd.;
B: Please contact the local office directly under Qingdao Hantek Electronic Co., Ltd.
C: Please contact the headquarters of Qingdao Hantek Electronic Co., Ltd.
Contact Method of our company:
Qingdao Hantek Electronic Co., Ltd.
http://www.Hantek.com
Address:35# Building No.780 Baoyuan Road,High-tech District,Qingdao China
Zip Code:266114
Telephone: [phone]
Fax: [phone]
Email: [e-mail]
Technical Support:
Telephone:[phone]
Email: [e-mail]

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 3 -
Summary of general safety matters
General Safety Summary
Please review the following safety precautions carefully before putting the instrument into
operation so as to avoid any personal injury or damage to the instrument and any product
connected to it. To prevent potential hazards, please follow the instructions specified in
this manual to use the instrument properly.
Avoid fire and personal injury.
Only authorized personnel can perform maintenance.
Use Proper Power Cord.
Only the exclusive power cord designed for the instrument and authorized for use within
the local country could be used.
Connect and disconnect correctly.
Connect the probe to the oscilloscope before connecting it to the circuit being
measured;Disconnect the probe and the circuit measured before disconnecting the probe
from the oscilloscope.
Ground the Instrument.
To avoid electric shock, the instrument is grounded through the Earth lead of the power
cord. The earth lead must be connected to the ground.This product must be grounded
before connecting any input or output terminals.
Connect the probe correctly.
If a probe is used, the probe ground lead must be connected to earth ground. Do not
connect the ground lead to high voltage. Improper way of connection could result in
dangerous voltages being present on the connectors, controls or other surfaces of the
oscilloscope and probes, which will cause potential hazards for operators.
Observe All Terminal Ratings.
To avoid fire or shock hazard, observe all ratings and markers on the instrument and
check your manual for more information about ratings before connecting the instrument.
Use Proper Overvoltage Protection.
Ensure that no overvoltage (such as that caused by a bolt of lightning) can reach the
product. Otherwise, the operator might be exposed to the danger of an electric shock.
Do Not Operate Without Covers.
Do not operate the instrument with covers or panels removed.
Provide Adequate Ventilation.
Inadequate ventilation may cause an increase of temperature in the instrument,which
would cause damage to the instrument. So please keep the instrument well ventilated and
inspect the air outlet and the fan regularly.
Use Proper Fuse.
Please use the specified fuses.
Avoid Circuit or Wire Exposure.
Do not touch exposed junctions and components when the unit is powered on.

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 4 -
Do Not Operate With Suspected Failures.
If you suspect that any damage may occur to the instrument, have it inspected by the
qualified maintenance personnel.
Do Not Operate in Wet Conditions.
To avoid short circuit inside the instrument or electric shock, never operate the instrument
in a humid environment.
Do Not Operate in an Explosive Atmosphere.
To avoid personal injuries or damage to the instrument, never operate the instrument in an
explosive atmosphere.
Keep Instrument Surfaces Clean and Dry.
To avoid dust or moisture from affecting the performance of the instrument, keep the
surfaces of the instrument clean and dry.
Prevent Electrostatic Impact.
Operate the instrument in an electrostatic discharge protective environment to avoid
damage induced by static discharges. Always ground both the internal and external
conductors of cables to release static before making connections.
Handle with Caution.
Please handle with care during transportation to avoid damage to keys, knobs,
interfaces, and other parts on the panels.
Safety Notices and Symbols
Safety Terms on the Product.There may be the following terms on the product:
DANGER It calls attention to an operation, if performed, could result in injury or hazard
immediately.
WARNING It calls attention to an operation, if performed, maybe not result in injury or
hazard immediately.
CAUTION It calls attention to an operation, if performed, could result in damage to the
product or other devices connected to the product.
Safety Symbols on the Product.There may be the following symbols on the product:
Safety Warning Protective Test Ground Shell Earth Terminal
Measurement Category
DPO6000/MPO6000 series digital oscilloscopes can make measurements in
Measurement Category I.

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 5 -
WARNING
This oscilloscope can only be used for measurements within its specified
measurement categories.
Measurement Category Definitions
Measurement category I is for measurements performed on circuits not directly
connected to MAINS. Examples are measurements on circuits not derived from MAINS,
and specially protected (internal) MAINS derived circuits. In the latter case,transient
stresses are variable. For that reason, the transient withstand capability of the equipment
is made known to the user.
Measurement category II is for measurements performed on circuits directly connected
to low voltage installations. Examples are measurements on household appliances,
portable tools and similar equipment.
Measurement category III is for measurements performed in building installations.
Examples are measurements on distribution boards, circuit-breakers, wiring(including
cables, bus-bars, junction boxes, switches and socket-outlets) in fixed installations,
equipment for industrial use and some other equipment. For example,stationary motors
with permanent connection to a fixed installation.
Measurement category IV is for measurements performed at the source of a low-voltage
installation. Examples are electricity meters and measurements on primary overcurrent
protection devices and ripple control units.
Ventilation Requirement
This oscilloscope uses fan to force cooling. Please make sure that the air intake and
exhaust areas are free from obstructions and have free air. When using the oscilloscope
in a bench-top or rack setting, provide at least 10 cm clearance beside,above and behind
the instrument for adequate ventilation.
WARNING
Inadequate ventilation may cause a temperature increase which can damage
the instrument.So please keep the instrument well ventilated during operation
and inspect the intake and fan regularly.
Working Environment
Temperature
Operating: 0℃to +50℃
Non-operating: -40℃to +70℃
Humidity
0℃to +30℃: ≤95% relative humidity
+30℃to +40℃: ≤75% relative humidity
+40℃to +50℃: ≤45% relative humidity
WARNING
To avoid short circuits inside the instrument or electric shocks, please do not
operate in humid environment.
Altitude
Operating: below 3 km
Non-operating: below 15 km
Care and Cleaning
Care

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 6 -
Do not store or leave the instrument where its LCD may be exposed to direct sunlight for
long periods of time.
CAUTION
To avoid damage to the oscilloscope or probe, do not expose it to fog,liquids
or solvent.
Cleaning
Check the oscilloscope and probe regularly according to its operating conditions. Please
follow these steps to clean the external surface of the instrument:
Remove dust from outside oscilloscopes and probes with a cloth that doesn’t fluff.Please
be careful not to scratch the bright screen filter material.
Use a soft cloth dampened with water to clean the oscilloscope.For more thorough
cleaning, use 75% isopropanol as an aqueous solvent.
WARNING
To avoid damage to the surface of the oscilloscope or probe, do not use any
corrosive or chemical cleaning reagent
Product End-of-Life Handling
Recycle:
Production of the equipment requires extraction and use of natural resources. If the scrap
of this product is not handled properly,then the substances the equipment contain could
be harmful to the environment or human health. To avoid the release of such substances
into the environment and reduce the use of natural resources, we recommend you to
recycle this product appropriately to ensure that most materials are reused properly.

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 7 -
DPO6000Z/MPO6000 Series Overview
DPO6000/MPO6000 Series is a Oscilloscope featuring extremely high memory depth,
wide dynamic range, clear display,high waveform capture rate and as many as 16 kinds of
triggering functions, 5 kinds of serial decoding functions it is a useful commissioning
instrument for various fields such as communication,aerospace, defense, embedded
systems, computers, research and education.
Main features:
★1 GSa/s real-time sample rate of the analog channels; 64 Mpts standard and 128M
maximum(6000EDU series) memory depth
★1 GSa/s real-time sample rate of the digital channels
★200 MHz, 100 MHz and 80 MHz analog channel bandwidth
★4 analog channels, 16(4*4) digital channels(MPO6000 series;DPO6000 can update to
use digital channels by buying LP104 digital probe)
★2-channel/3-channel signal source(MPO6000EDU is 3-channel ),13 kinds of waveform
inside,4 sets of arbitrary waveform,200M sample rate,8Kpts waveform length
★60,000 wfms/s (dots display)/400,000 wfms/s (dots display quick acquisition mode)
waveform capture rate
★Segmented acquisition function,support to capture up to 80,000 sections
★256 grade color display
★Low base noise, 500 uV/div to 10 V/div ultra-wide vertical dynamic range
★7.0 inch WVGA (800*480) TFT LCD, with ultra-wide screen, vivid picture, low power
consumption and long service life
★7 inch capacitive touch screen,support multi-touch(touch screen is optional)
★Adjustable waveform brightness and display brightness
★Up to 16 kinds of trigger functions, including 5 kinds of protocol triggers
★Supply 5 serial decoding options
★Auto measurement of 42 kinds of waveform parameters (with statistics)
★5 bits digital voltage meter and 6 bits hardware frequency indicator function
★Bode diagram function(the oscilloscopes with signal source function can use)
★Event search function
★2-window display function
★Built-in FFT function
★Multiple waveform math operation functions【MATH】
★Standard interfaces: USB Device, USB Host, LAN
★Wifi(MPO6000EDU/DPO6000EDU can use Wifi)
★Optional interfaces: HDMI,UART,AUX
★Pass_fail /trig_out(EDU standard,non-EDU optional)
★Conform to LXI CORE 2011 DEVICE class instrument standards; enable quick,
economic and efficient creation and reconfiguration of test system
★Supports remote command control
★Built-in help to facilitate information acquisition
★Supports multiple languages
★Novel and delicate industrial design and easy operation

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 8 -
This list of product models
MPO6000/DPO6000 series include the following modes. Unless otherwise specified, this
manual takes MPO6204EDU as an example to illustrate the functions and operation
methods of MPO6000/DPO6000 series.
Modes
channel
Analog
bandwidth
Signal
generator
Logic
analyzer
Wifi
DPO608XB
2/4
80MHz
-
-
-
DPO610XB
2/4
100MHz
-
-
-
DPO620XB
2/4
200MHz
-
-
-
DPO608XC
2/4
80MHz
25MHz*2
-
-
DPO610XC
2/4
100MHz
25MHz*2
-
-
DPO620XC
2/4
200MHz
25MHz*2
-
-
MPO608XD
2/4
80MHz
25MHz*2
4*4 LA
-
MPO610XD
2/4
100MHz
25MHz*2
4*4 LA
-
MPO620XD
2/4
200MHz
25MHz*2
4*4 LA
-
DPO608XEDU
2/4
80MHz
-
-
Yes
DPO610XEDU
2/4
100MHz
-
-
Yes
DPO620XEDU
2/4
200MHz
-
-
Yes
MPO608XEDU
2/4
80MHz
25MHz*3
4*4 LA
Yes
MPO610XEDU
2/4
100MHz
25MHz*3
4*4 LA
Yes
MPO620XEDU
2/4
200MHz
25MHz*3
4*4 LA
Yes

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 9 -
1.Quick Start
This chapter introduces the precautions when using the oscilloscope for the first time,the
front/rear panels of the oscilloscope, the user interface and the using method of the
built-in help system.
1.1.General Inspection
1.1.1.Inspect the packaging
If the packaging or foam plastic cushioning has been damaged, do not dispose it until the
machine and accessories have passed both electrical and mechanical tests.
1.1.2.Inspect the instrument
In case of any appearance damage, not working normally, or failure in passing the
electrical and mechanical tests, contact the representative in charge of this business.
1.1.3.Check the accessories
Please check the accessories according to’’ Appendix A:Accessories’’ after the manual. If
the accessories are damaged or incomplete, please contact the representative in charge
of this business.
1.2.Appearance and Dimensions
Front View
Top View
1.3.To Prepare the Oscilloscope for Use
1.3.1.To Adjust the Supporting Legs

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 10 -
Adjust the supporting legs properly to use them as stands to tilt the oscilloscope upwards
for stable placement of the oscilloscope as well as better operation and
observation.
To Adjust the Supporting Legs
1.3.2.To Connect to Power Cord According to your Demand
The power requirements of the oscilloscope are AC 100-120 V, 50/60/400 Hz or AC
100-240 V, 50/60Hz,50W max. Please use the power cord supplied with the accessories
to connect the oscilloscope to the AC power source as shown in the figure below
To Connect to Power Supply
1.3.3.Power-on Inspection
When the oscilloscope is energized, pressing the power key at the lower-left corner of
the front panel can start the oscilloscope. During the start-up process, the oscilloscope
performs a series of self-tests.In the process of self-test, the keyboard indicator light will
be lit in a certain order.After the self-test, the welcome screen is displayed.
1.3.4.Probe Check
1.3.4.1.Safety
When using the probe, keep your fingers behind the guard on the probe body to avoid
electric shock. Do not touch metallic portions of the probe head while it is connected to a
voltage source.Connect the probe to the oscilloscope and connect the ground terminal to
ground before you start any measurements.
Power

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 11 -
1.3.4.2.Probe Attenuation Setting
Probes are of various attenuation factors which affect the vertical scale of the signal. The
Probe Check function is used to verify if the Probe attenuation option matches the
attenuation of the probe.
Press a vertical menu button (such as the CH1 MENU button) and select the Probe option
that matches the attenuation factor of your probe.
Make sure that the Attenuation switch on the probe matches the Probe option in the
oscilloscope.Switch settings are 1X and 10X.When the Attenuation switch is set to 1X, the
probe limits the bandwidth of the oscilloscope to 6MHz. To use the full bandwidth of the
oscilloscope, be sure to set the switch to 10X.
1.3.5.To Connect the Probe
DPO6000 series oscilloscope standard equipped passive probe,MPO6000 series
standard equipped passive probe and digital probe.
1.3.5.1.Connect the passive probe:
1.Connect the BNC terminal of the probe to an analog channel input terminal of the
oscilloscope at the front panel.
2.Connect the ground alligator clip or spring of the probe to the circuit ground terminal and
connect the probe tip to the circuit to be tested.
1.3.5.2.Connect the logic probe:
1.Connect one terminal of the logic probe to the digital channel input terminal at the front
panel of the oscilloscope correctly(digital probe doesn’t have directions).
2.Connect the signal under test to the other terminal of the logic probe. MPO 6000 series
is equipped with 4 LP104 digital probes(standard).
1.3.6.Use of Probe Check Wizard
Every time you connect a probe to an input channel, you should use the probe check
wizard to verify that this probe is operating correctly.Use the vertical menu (for example,
push the CH1 MENU button) to set the Probe option attenuation factor.
1.3.7.Manual Probe Compensation
Upon the first connection of a probe and an input channel, you should manually perform
this adjustment to match the probe to the input channel. Uncompensated or
miscompensated probes may lead to errors or faults in measurement. To adjust the probe
compensation, follow the steps below:

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 12 -
1.Set the Probe option attenuation in the channel menu to 10X. Set the switch on the
probe to 10X and connect the probe to Channel 1 on the oscilloscope. If you use the
probe hook-tip, ensure it is firmly inserted onto the probe. Attach the probe tip to the
PROBE COMP ~2V@1KHz connector and the reference lead to the PROBE COMP
Ground connector.Display the channel and then press the ‘‘Auto Scale’’ button.
2.Check the shape of the displayed waveform.
Compensated correctly
Overcompensated
Undercompensated
3.If necessary, use a nonmetallic screwdriver to adjust the variable capacity of your probe
until the shape of the waveform turns to be the same as the above figure. Repeat this step
as necessary. See the figure below for the way of adjustment.
1.4.Front Panel Overview
The following content briefly describes and introduces the front panel of this series of
oscilloscopes, so that you can be familiar with this series of digital oscilloscopes in the
shortest time.
Front Panel Descriptions
No.
Description
No.
Description
1
LCD
9
Vertical control system

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 13 -
2
To turn on/off the menu
10
Signal source 1 output channel
3
Signal source function(only the
oscilloscopes with signal source
function)
11
CH1~CH4 signal input channel
4
Multifunction knob
12
Signal source 2 output channel
5
The functions buttons of menu
13
LA1~LA4 signal input channel
(only MPO series oscilloscopes)
6
Horizontal control system
14
Probe compensation signal
output terminal/ground terminal
7
Trigger control system
15
USB Host port
8
Shortcut key(Run/Stop,Single,Auto
Scale)
16
Power on/off
1.5.Rear Panel Overview
1.Handle
Pull up the handle vertically for easy carry of the instrument. When you do not need the
handle, press it down.
2.AC Power Socket
AC power input terminal. The power requirements of this oscilloscope are 100-120 V,
50/60/400 Hz or 100-240 V, 50/60 Hz,50W max. Use the power cord provided with the
accessories to connect the instrument to AC power. Then, you can press the power key at
the front panel to start the instrument.
3.AUX Trigger Out and Pass/Fail(optional terminal)
Trigger Out:
The oscilloscope can output a pulse at each trigger via this interface,which is the current
signal the oscilloscope capture. Connect the signal to a waveform display device and
measure the frequency of the signal. The measurement result is the same with the current
capture rate.
Pass/Fail:
The instrument can output a pulse via this connector when a failed waveform is detected
during the pass/fail test. The instrument continuously outputs a low level via this connector
when no failed waveform is detected.
4.Signal Source 3 Output(EDU series)
Signal 3 output only the build-in 3-channel signal source When source 3 is enabled,the
signal can be output through signal terminal according to the current setting.
5.USB Device

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 14 -
You can connect the oscilloscope to a PictBridge printer or PC via this interface.When a
PC is connected, users can send SCPI commands using the PC software or control the
oscilloscope via user-defined programming. When a printer is connected, users can print
the waveform displayed on the screen using the printer.
6.LAN/UART
LAN
Connect the instrument to network via this interface for remote control. This oscilloscope
conforms to the LXI CORE 2011 DEVICE class instrument standards and can quickly
build test system.
UART(optional interface)
Connect the instrument to control system via this interface for remote control.
7.HDMI(optional interface)
Connect the instrument to the screen with HDMI display via this interface for greater
display.

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 15 -
2.Front Panel Function Overview
2.1.Main keys introduction
2.1.1.HORIZONTAL
Horizontal Offset :
Modify the horizontal position. The trigger point would move left or right
relative to the center of the screen when you turn the knob.During the
modification,waveform of all the channels would move left or right and the
horizontal position message at the upper-right corner of the screen would
change accordingly. Press down this knob to quickly reset the horizontal
position.
HORIZONTAL Time Base:
Modify the horizontal time base. Turn clockwise to reduce the time base
and turn counterclockwise to increase the time base. During the
modification, waveform of all the channels will be displayed in expanded
or compressed mode and the time base message at the upper side of the
screen would change accordingly. Press down this knob to quickly switch
single-window or dual-window display modes.
2.1.2.VERTICAL
analog channel setting keys. Press any key to open the corresponding
channel menu and press again to turn off the channel.
Math:
Press this key to open the math operation menu,press again to close the
math function
VERTICAL Offset:
modify the vertical position of the current channel waveform. Turn
clockwise to increase the position and turn counterclockwise to decrease.
During the modification, the waveform would move up and down and the
position message at the lower-left corner of the screen would change
accordingly. Press down this knob to quickly reset the vertical position to
zero.
VERTICAL Voltage:
modify the vertical scale of the current channel. Turn clockwise to
decrease the scale and turn counterclockwise to increase. During the
modification, the display amplitude of the waveform would enlarge or
reduce. The scale information at the lower side of the screen would
change accordingly. Press down this knob to quickly switch the vertical
scale adjustment mode between "Coarse" and "Fine".
2.1.3.Signal Source

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 16 -
Signal Source key:
Press this key to enter the source setting interface to set the output signal
waveform and parameters
Note: This function is only applicable to digital oscilloscopes with signal source function.
2.1.4.TRIGGER
Trigger level:
modify the trigger level. Turn clockwise to increase the level and turn
counterclockwise to reduce the level. During the modification, the trigger
level line would move up and down and the value in the trigger level
message box at the lower-left corner of the screen would change
accordingly. Press down the knob to quickly reset the trigger level to the
trigger data source zero point.
Trig Menu:
press this key to open the trigger operation menu.This oscilloscope provides
various trigger types. For more details, please refer to “Trigger System”.
Force Trig:
Short press this key to generate a trigger signal forcefully.
Long press this key to turn on history waveform.
2.1.5.AUTO
Auto Scale:
Press this key to enable the waveform auto setting function. The
oscilloscope will automatically adjust the vertical scale,horizontal time base
and trigger mode according to the input signal to realize optimum waveform
display.
2.1.6.RUN/STOP
Run/Stop:
press this key to "RUN" or "STOP" waveform sampling. In the "RUN" state,
the key is illuminated in green. In the "STOP" state, the key is illuminated in
red.
2.1.7.SINGLE
Single:
Press this key to set the trigger mode to "Single". In single trigger mode,
press FORCE to generate a trigger signal immediately.
2.1.8.Multifunctional Knob
V0:
Use this knob can do many settings,such as adjusting waveform
brightness,trigger time,selecting trigger types,selecting trigger source,the
waveform frequency offset and amplitude of signal source; In
non-menu-operation mode, the indicator light of the knob doesn’t go on, In
menu operation, the indicator light of the knob goes on.Turn this knob can
adjust the settings above, Turn clockwise to increase and counterclockwise
to reduce,press down to select this option.
2.1.9.Function Menus

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 17 -
Default:
Short press this key to perform the corresponding settings.
Long press to enter into Default function preset,you can select
factory settings,default settings and user settings.
Help:
Press this key to turn on or off the online help system.
Utility:
press this key to enter the system function setting menu to set the
system-related functions or parameters, such as the interface,
sound and language.Besides, some advanced functions (such as
the pass/fail test) are also supported.
Cursor:
press this key to enter the cursor measurement menu. The
oscilloscope provides two cursor modes.
Meas:
press this key to open the measurement setting menu. You can
set the measurement source, turn on or off the DMM, all
measure, statistic function and etc. Press “all measure” to open
the measurement of 42 waveform parameters. The measurement
result will be displayed at the bottom of the screen.
Save/Recall:
press this key to enter the file save and recall interface. The types
of the file that can be stored include setups, waves,parameters
and CSV. Internal and external storage as well as disk
management are also supported.Long press this key to save
pictures to external storage device(USB disk),the picture format
is .bmp.
Display:
Short press this key to enter the display setting menu to set the
display type,persistence time, wave intensity, screen grid and grid
brightness.
Long press this key to clear persistence then collect or count
again.
2.2.User Interface
This section will let you understand the front operating panel of this series of digital
oscilloscopes before using them.
1.Hantek brand
Open in touch screen is to display QR code,scan to enter download help page quickly.
2.Trigger Status:
Auto:The oscilloscopes work in auto mode,will acquire waveform without trigger.

DPO6000，MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1
- 18 -
READY: All pre-trigger data has been acquired and the oscilloscope is ready to accept the
trigger.
TD:The oscilloscope has been triggered.
Roll:In roll mode,the oscilloscopes will acquire and display waveform data continuously.
Stop:The oscilloscopes will stop acquiring waveform data.
ARM:Pre-trigger state.
3.The main time base of current window
Represents the length of time represented by each grid on the horizontal axis of the
screen.
4.Sampling rate,sampling point
Displays the current sampling rate and storage depth of the analog channel.
The sampling rate and storage depth vary with the horizontal base.
5.Waveform storage
6.Horizontal trigger time
Use the horizontal offset knob to adjust this parameter.Press the knob to quickly reset the
horizontal displacement.
7.Trigger level
Use the trigger level knob to adjust this parameter.Press the knob to quickly reset the
trigger level.
8.Operating menu to display the different information of each function keys
9.The time display of the oscilloscope
10.Wifi status display
11.Display the connection status of LAN
If the icon is lit or activated,the LAN is connected.
12.Display USB device status
If the icon is lit or activated,the USB guest is connected.
13.Display USB host status
If the icon is lit or activated,the USB host is connected.
14.Display LA status
If the icon is lit or activated,the LA channel is connected.
15.Display Gen3 status(some modes)
If the icon is lit or activated,the Gen3 channel is turned on.
16. Display Gen2 status(some modes)