Harbor Breeze DUBOIS DM52BCP5CS User manual

Federal regulations require ceiling fans with light kits manufactured or imported after
January 1, 2009, to limit total wattage consumed by the light kit to 190W. Therefore,
this fan is equipped with a wattage limiting device. If you lamp this fan's light kit with
bulbs totaling more than 190W, the wattage limiting device will reduce the watts
consumed to 190W.
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
EB14489 1
Lowes.com/harborbreeze
E192641
LISTED
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. -
5 p.m., EST, Friday.
Harbor Breeze® is a registered trademark
of LF, LLC.All Rights Reserved.
Español p. 21
DUBOIS CEILING FAN
MODEL #DM52BCP5CS
ITEM #0125519
Español p. 22

Safety Information ....…………………………………………………………………………...……....... 2
Package Contents ........…………………………………………………………………..……..…..….. 4
Hardware Contents ......................................................................................................................... 5
Preparation .......................….…………………..……………………….…………….………………..... 5
Initial Installation ............................……………………...…………………………………................... 6
Downrod-Style Fan Mounting .....…………………………....……………....……................................ 7
Closemount-Style Fan Mounting ..........…....................…...............…....……………………............ 10
Wiring ......................................................................................………………………....................... 11
Final Installation .............................……………………….……….................................................... 13
Operating Instructions..............................................................………………………....................... 17
Care and Maintenance ....………………………………………………………………......................... 18
Troubleshooting ........................………...………………………….……………..……........................ 19
Limited Lifetime Warranty ……….…………………………………………..….................................... 20
Replacement Parts List ................................................................................................................. 21
TABLE OF CONTENTS
2Lowes.com/harborbreeze
SAFETY INFORMATION
READ AND SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, install or operate the
product.
• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for
repairs, it must be shipped in its original packaging to ensure proper protection against damage
that might exceed the initial cause for return.
• Make sure all electrical connections comply with local codes, ordinances, the National Electrical
Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring
handbook if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to
the floor and at least 30 in. from the end of the blades to any obstruction.
• After you install the fan, make sure all connections are secure to prevent the fan from falling.
• The net weight of this fan, including the light kit, is: 22.9 lbs.

SAFETY INFORMATION
To reduce the risk of fire, electrical shock or personal injury, mount fan to outlet box
marked "ACCEPTABLE FOR FAN SUPPORT OF 35 LBS. (15.9 KG) OR LESS" and use
mounting screws provided with the outlet box. Most outlet boxes commonly used for the
support of lighting fixtures are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
When mounting fan to a ceiling outlet box, use a METAL octagonal outlet box. Secure the outlet
box directly to the building structure. The outlet box and its support must be able to support the
moving weight of the fan (at least 35 lbs.). Do NOT use a plastic outlet box.
To avoid personal injury, the use of gloves may be necessary while handling fan parts with
sharp edges.
To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan
are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your
house wire is larger than 12-gauge or there is more than one house wire to connect to the
corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.
To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed control
device or control fan speed with a full range dimmer switch.
To reduce the risk of fire, electrical shock or personal injury, do not bend the blade arms when
installing them, balancing the blades or cleaning the fan. Do not insert objects between the
rotating fan blades.
To reduce the risk of personal injury, use only parts provided with this fan. The use of parts
OTHER than those provided with this fan will void the warranty.
WARNING
CAUTION
Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid
electrical shock.
Read all instructions and safety information before installing your new fan. Review the
accompanying assembly diagrams.
3
Lowes.com/harborbreeze

4
PACKAGE CONTENTS
Lowes.com/harborbreeze
DESCRIPTIONPART QUANTITY
IMPORTANT REMINDER: You must use the
parts provided with this fan for proper installation
and safety.
A Downrod 1
B Canopy 1
C Mounting Bracket 1
D Motor Housing 1
E Fitter Plate Screw 3
(preassembled)
F Yoke Cover 1
G Light Kit Fitter 1
H Blade Arm 5
I Blade 5
J Glass Shade 4
DESCRIPTIONPART QUANTITY
K Motor Screw 10
(preassembled)
L Lock Washer 10
(preassembled)
M Canopy Mounting Screw 4
(preassembled)
N Pin (preassembled) 1
O Clip (preassembled) 1
P Pull Chain Extension 2
Q Socket Ring 4
(preassembled)
R Switch Housing 1
S Bulb 4
T Balancing Kit 1
G
P
H
E
N
I
L
D
R
O
K
S
J
Q
T
C
F
B
A
M

HARDWARE CONTENTS (shown actual size)
AA
Blade
Screw
Qty. 15
+ 1 extra
5
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble the product.
Estimated Assembly Time: 120 minutes
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety
Glasses, Stepladder and Wire Strippers
Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself Wiring Handbook
(available at Lowe’s) and Wire Cutters
DANGER: When using an existing outlet box, make sure the outlet box is securely attached to
the building structure and can support the full weight of the fan. Failure to do this can result in serious
injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan
after installation is complete.
CAUTION: Be sure outlet box is properly grounded and that a ground wire (green or bare) is
present.
After opening top of carton, remove mounting hardware package from foam inserts. Remove motor
from packing and place on carpet or on foam to avoid damage to finish.
CAUTION: Carefully check all screws, bolts and nuts on fan motor assembly to ensure they are
secured.
PREPARATION
CC
E3 Wire
Connector
Qty. 4
BB
Fiber
Blade
Washer
Qty. 15
+ 1 extra
Lowes.com/harborbreeze
Hex
Nut
Qty. 1
Lock
Washer
Qty. 1
DD EE

Turn off circuit breakers and wall switch to the fan
supply line leads.
DANGER: Failure to disconnect power supply
prior to installation may result in serious injury or
death.
1.
3. Check to make sure blades (I) will be at least 30 in.
from any obstruction and at least 7 ft. above the
floor.
INITIAL INSTALLATION
ON
OFF
ON
OFF
3
1
Lowes.com/harborbreeze
7 ft.
min.
30 in.
min.
2.
I
6
Determine mounting method to use.
A. Downrod-style (standard or angled ceiling)
B. Closemount-style (standard ceiling only)
IMPORTANT: If using the angle mount, ensure the
ceiling angle is not steeper than 19°.
*Helpful Hint: Downrod-style mounting is best suited
for ceilings 8 ft. high or higher. For taller ceilings you
may want to use a longer downrod (not included).
Angle-style mounting is best suited for angled or
vaulted ceilings. A longer downrod is sometimes
necessary to ensure proper blade clearance.
A
B
2

INITIAL INSTALLATION
4. Secure mounting bracket (C) to outlet box (not
included) using screws, spring washers and flat
washers provided with the outlet box.
*NOTE: It is very important you use the proper
hardware when installing the mounting bracket (C)
as this will support the fan.
IMPORTANT: If using the angle mount, make sure
open end of mounting bracket (C) is installed facing
the higher point of the ceiling.
4
4
5. Remove motor screws (K) and lock washers (L)
from underside of motor housing (D). Set aside for
later use. [If there are plastic motor blocks installed
with the motor screws (K) and lock washers (L),
discard the plastic motor blocks.]
Remove pin (N) and clip (O) from yoke at the top of
motor housing (D) and partially loosen
preassembled set screws and nuts.
1.
DOWNROD-STYLE FAN MOUNTING
7
Lowes.com/harborbreeze
For DOWNROD-STYLE FAN MOUNTING, proceed
to step 1 below. For CLOSEMOUNT-STYLE FAN
MOUNTING, skip to page 10.
Set
Screws
and Nuts
1
D
N
O
Open End
C
C
5
J
K
D
Plastic
Motor
Block
K
L
Yoke
Standard Mount Angle Mount

Slip downrod (A) into yoke, align holes and
re-install pin (N) and clip (O). Tighten set
screws in yoke and then tighten preassembled
nuts on the set screws.
DOWNROD-STYLE FAN MOUNTING
Depending on the length of downrod you use,
you may need to cut the lead wires back to
simplify the wiring. If you decide to cut back the
lead wires, it is suggested you do so in the
following manner:
Take the lead wires and make sure you have
pulled them all the way through the top of the
downrod. Start at the TOP of the ball on the
downrod and measure 8 in. of lead wire, and
then cut the excess wire off with wire cutters (not
included).
NOTE: If you do not cut back the lead wires,
Steps 4 and 5 are not necessary and you may
proceed to Step 6 instead.
4.
2. Insert downrod (A) through canopy (B) and
yoke cover (F). Thread wires from motor
housing (D) up through downrod (A).
3.
2
8
Lowes.com/harborbreeze
F
B
A
D
A
O
N
F
B
3
Ball
4
Set Screws
Set Screws
and Nuts
and Nuts
Sideview
Sideview

9
Lowes.com/harborbreeze
If you decided to cut back the lead wires in Step 4,
strip 1/2 in. of insulation from end of white wire.
Twist stripped ends of each strand of wire within
the insulation with pliers (not included). Repeat
Step 5 for black, blue (if applicable) and green
wires.
5. 5
DOWNROD-STYLE FAN MOUNTING
Install ball end of downrod (A) into opening of
mounting bracket (C). Align slot in ball with tab in
mounting bracket (C).
DANGER: Failure to align slot in ball with tab
may cause the fan to wobble or fall, which could
result in serious injury or death.
Continue to WIRING on page 11.
6.
Slot
Tab
C
A
6

CLOSEMOUNT-STYLE FAN MOUNTING
2.
3.
1. Remove canopy cover from bottom of canopy (B).
[NOTE: It may be necessary to use the handle end
of a screwdriver (not included) to remove the
canopy cover by tapping on the canopy cover from
the inside of the canopy (B).]
*Helpful Hint: Closemount-style mounting is more
suitable for ceilings lower than 8 ft. high. The
downrod (A), hanging ball, yoke cover (F) and
canopy cover are not used in this type of
installation.
D
3
Remove every other screw and lock washer from
top of motor housing (D).
Pull wires up through hole in the middle of the
canopy (B) and attach canopy (B) to motor
housing (D) using the three screws and three lock
washers previously removed. B
10
Lowes.com/harborbreeze
D
Canopy
Cover
B
1
B
D
2
D