Harvest TEC 695 User manual

1
695-19-OPR
6/20
Operation Manual
Model 695
100 Gallon Preservative Applicator for Claas 5300
Forage Harvester

2
DECLARATION OF INCORPORATION
MANUFACTURER: Harvest Tec Inc.
2821 Harvey St.
P.O. Box 63
Hudson, WI 54016, U.S.A.
REPRESENTATIVE ESTABLISHED IN COMMUNITY: Profitable Farming Company
Middle Barlington, Roborough
Winkleigh, Devon, EX19 8AG
ENGLAND
The person above certifies and declares that:
VIRTUAL MACHINE: Equipment mounted on a farm press and for the application of innoculants onto forage crops.
MODEL: 695-19-OPR
BRAND: Harvest Tec
SERIAL NUMBER:
This application preservatives for hay Harvest Tec system meets the Directive 2006/42/EC of the European Parliment and
the Council of 17 May 2006 and other applicable European Directives including Directive 2004/108/EC on the
Electromagnetic compatability.
The application of preservatives for hay Harvest Tec system will be turned on after being installed on a farm press has
been declard in conformity with the Machinery Directive.
Person in the community authorized to provide information on the partly completed machinery and making this statement:
Richard Snell, President, Profitable Farming Company
Signed on May 21, 2011: Middle Barlington, Roborough
Winkleigh, Devon, EX19 8AG
ENGLAND

3
Harvest Tec Model 695 Operations Table of Contents
PAGE
Introduction
4
System Requirements
4
Tools Needed
4
Safety
4
Safety Decals
5
Preparing the Applicator for Operation
6-9
Filling the tank
6
Operation
7-18
Downloading the Harvest Tec App
7
Shutting Down the Hay App
8
iPad Integration Control Module
9
Bluetooth Receiver Lights
9
Device Selection
10
Manual Selection & Recommended Preservative
11-12
Tab Descriptions
12
Screen Menus
13-17
Setup Mode
14-17
Software Versions
17
Job Records
18-19
First time and Annual Startup
20
Setting up System for Operation
21-29
Application Rate
21
Baling Rate
22
Bailing Rate Settings –Baler Sensors
22
RFV Setup
23
Operation Instructions
24
Manual Mode
25
Job Records
26
Download Job Records
27
Export Job Records
28-29
Wiring Diagram
30
Maintenance
31-32
Winter Storage
33
Status Alerts
33
Pin Outs
34-36
Common Questions
37
Troubleshooting
38-39
Parts Breakdown
40-
Tank, Saddle & Legs
40
Pump Manifold
41
Star Wheel Moisture Sensors
42
Bale Rate Sensors & Harness
42
Control and Harnesses
43
Hose and Drain Fill Line
44
Optional iPad Mini Mounting Kit
45
Optional iPad Display Kit
46
4537B Installation Kit
47
Notes
48-50
Warranty statement
51

4
Introduction
Thank you for purchasing a Harvest Tec Model 695 Hay Preservative Applicator. This 695 applicator system
has been designed to be operated through an Apple iPad (not included) using the Hay App. As well as the
option to plug directly into most tractors that have an ISOBUS Monitor. The 695 Applicator System offers these
advantages by operating through an Apple iPad:
1. Large bright, clear, colorful display
2. More durable and can be read in bright sunlight
3. Wireless connection in cab
4. Can be used for multiple other uses than just the applicator display
5. Option to tie-into the tractor ISOBUS system
The 695 Hay Preservative Applicator System is designed to apply buffered propionic acid to the forage crop as
it is baled and will adjust the rate of application based on moisture and tonnage of the crop being harvested.
The model 695 base kit includes: tank, frame, pumps, hose, and the Dual Channel Processor (DCP). This
manual will take you through the steps for installing the applicator. If you are unsure about installing the system
after consulting this manual, contact your local authorized dealership for additional assistance. If you are in
need of parts for the system please see the parts breakdown in the back of this manual and contact your local
authorized dealer to order the parts. This applicator is designed to apply Harvest Tec buffered propionic acid.
Right and Left sides are determined by facing in the direction of forward travel.
*Made for iPad®(3rd through Pro 2nd generation), running the current i4OS operating system
or one version previous required for iPad option
*iPad is a trademark of Apple Inc., registered in the U.S. and other countries.
**600 Series Applicators with serial number before DCP27000 will require the DCP to be sent to Harvest
Tec for a required update in order to use the iPad Integration Module (030-6672C).
*Hay App version must be at least 2.7.1 (or higher) to operate with the iPad Integration Module
Tools Needed:
- Standard wrench set
- Standard nut driver set
- Electric drill and bits
- Standard socket set
- Side cutter
- Hammer
- Crescent wrench
- Metal cutting tools
- Standard screwdriver
- Hose cutter
- Center punch
Safety
Carefully read all the safety signs in this manual and on the applicator before use. Keep signs clean and
visible. Replace missing or damaged safety signs. Replacement signs are available from your local authorized
dealer. See your installation manual under the replacement parts section for the correct part numbers.
Keep your applicator in proper working condition. Unauthorized modifications to the applicator may impair the
function and/or safety of the machine.
Carefully read and understand all of the baler safety signs before installing or servicing the baler. Always use
the supplied safety equipment on the baler to service the applicator.

5
Safety Decals
Number 1
Spraying hazard. Disconnect power before servicing the
applicator
Part no. DCL-8007
Number 2
Falling hazard. Do not step in this area.
Part no. DCL-8002
Number 3
Use caution when working around chemicals. Wear all
protective equipment according to the label of the
product.
Part no. DCL-8006
Number 4
Read and understand the operator’s manual before using
or working around the equipment.
Part no. DCL-8000
Number 5
Open (unlocked) and closed (locked) position of the ball
valve.
Part no. DCL-8004

6
Preparing the Applicator for Operation
After the Applicator has been installed on the baler, please follow the steps below to prepare for operating the
applicator both safely and correctly.
Filling the tank:
Read the label of the product you choose to fill the tank to determine individual protective measures you the
operator should take. Locate the drain/fill line on the right side of the baler. Open the cam-couplers (A) and
remove the protective plug (B).
Insert the male coupler (found on transfer pump) into the female cam and close the cams (A). To open the ball
valve (C) turn the handle so it is vertical. After the ball valve has been turned on switch the pump to the On
position. Monitor the level on the tank visually and shut off the pump before over filling. Once the pump is
turned off, close the ball valve and remove the male coupler.
The handle of the ball valve (C) will be horizontal when closed. Reinstall the protective plug and close the
cams. The Harvest Tec model 9212 and 9215 transfer pumps are recommended for this process.
Water is recommended for first time and annual start up procedures.
Drain/Fill line on right side of baler
Enlarged view of the drain/fill line valve
and cam-coupler assembly.
A
B
C

7
Hay App
Operation
Turn On / Off iPad using the Sleep/Wake button
*(Info from Apple User’s Guide)
Turn iPad on. Hold down the Sleep/Wake button until Apple logo appears. iPad will take a moment to load.
You can lock iPad and put it to sleep when you’re not using it. Locking
iPad puts the display to sleep, saves the battery, and prevents
anything from happening if you touch the screen.
When you are not going to use the iPad for an extended period of time put the unit into sleep mode by pressing
the Sleep/Wake button. Press Sleep/Wake button to wake iPad and then unlock iPad by entering passcode.
Turn iPad off. Hold down the Sleep/Wake button for a few seconds until the slider appears onscreen, then drag
the slider to the right.
Downloading Harvest Tec App
1. If iPad does not have Wi-Fi turned on, select the Settings tab then select the Wi-Fi tab (below).
4. Select an available network when detected by the iPad, shown in area above that currently says ‘Other.’
5. Select App Store icon (below) and open. *You will need a Wi-Fi connection available to view App Store.
Download the Hay App in the App Store by searching for
‘Hay App’ in the search bar in the top right corner of screen (right):
*The advertisements displayed on the App Store screen will change.
The app will have the icon as shown:
Note: Made for iPad®(3rd through Pro 2nd generation), running the current iOS operating system
or one version previous required for iPad option
Sleep/Wake Button
2. Turn Wi-Fi on by sliding button to the right.
*Green bar indicates ON
3. Use same process to turn on Bluetooth function
**The Harvest Tec system WILL NOT
appear under the Bluetooth tab in the
Setting App. Open the Hay App to
connect.

8
Shutting Down the Hay App
To shut down the Hay App double click the home button (Figure A). This will show the open apps that are
running on your iPad (Figure B).
*Note: By pressing the home button one time to return to the home screen, the Hay App does not shut down.
The system will however, stop applying preservative after 10 seconds.
Slide the app you want to shut down by sliding the app toward the top of the iPad, until the app is no longer
visible (Figure C).
Figure A
Figure B
Figure C

9
iPad Integration Control Module
To operate the applicator, connect the iPad cord to the iPad
Integration Control in the port indicated by:
iPad Integration Control Light Signals
Green Slow Blink –Power supplied to the applicator system and the unit is going through its
startup process. This will take approximately 25-35 seconds.
Green Double Blink –Indicating the iPad module recognizes the iPad but the app is not open or connected.
Green Solid Light –Module is connected to the app and is ready to operate.
*Recommended to use the USB cable included with the applicator kit (006-6672USBC)
Bluetooth Receiver Lights
Pre-2020 applcaitors equipped with Bluetooth receivers (030-6672B)
are now equipped with lights to indicate both power and Hay App
connection on the Apple iPad. Clean light regularly
Blinking Lights –System is waiting for the processor to connect, which
could take up to 35 seconds.
Red Light –The Bluetooth receiver has power
Green Light –The Bluetooth receiver is connected to the Hay App.
**600 Series Applicators with serial number before DCP27000 will require the DCP to be sent to Harvest
Tec for a required update in order to use the iPad Integration Module (030-6672C).
Hay App version must be at least 2.7.1 (or higher) to operate with the iPad Integration Module
*Made for Apple iPad badge
Use of the Made for Apple iPad badge means that an accessory has been designed to connect specifically to
the Apple product(s) identified in the badge and has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the operation of this device or its compliance with safety
and regulatory standards.
Please note that the use of this accessory with an Apple product may affect wireless performance.
030-6672C

10
Operating the Harvest Tec iPad App (continued)
When ready to operate your applicator system, open the Hay App on the iPad by selecting the Hay App icon.
Device Selection
The app will open to the Device Menu screen as shown below.
Pre-2020 applicators which are equipped with the Bluetooth receiver (030-6672B) that are within range (20’) of
the iPad and have power going to them, will be shown under the Active Connections section (below) after the
initial startup of the system (35-45 seconds).
Production year 2020 applicator systems and beyond will include the iPad Integration Module 030-6672C.
When plugging in the iPad cord to the module the app will change to the applicator Main Menu for immediate
operation. Unplug the cord to return to the Device Menu page.
*Hay App version must be at least 2.7.1 (or higher) to operate with the iPad Integration Module (030-6672C)
The In-Active Connections section will show applicator systems that have been connected in the past, but are
not within range of the iPad or do not currently have power going to them (bottom left).
To remove a baler from the In-Active list, slide the bar displaying the baler name to the left, and select the
Delete button that will appear (bottom right).
After the iPad connects to
the Bluetooth receiver,
select the applicator you
want to connect with.

11
Operating the Harvest Tec iPad App (continued)
Manual Selection
Selecting the Manual button (below) displayed to the right of the baler name will open the operation manual for
your baler.
*Use the following information for Large Square Balers.
*You do not need to be connected to a baler to open the manual after a baler has been connected.
When finished reviewing the manual, press the Done button in the top left corner to return to the Device Menu.
Recommended Preservative
To view recommended preservative information, application rates, and frequently asked preservative
questions, select Recommended Preservative (below).
*You do not need to be connected to a baler to open the recommended preservative page.

12
Operating the Harvest Tec iPad App (continued)
Once you have selected the baler you want to connect with from the Device Menu, the applicator main menu
will display (below).
Tab Descriptions
Automatic Mode: This mode allows you to use all of the applicator features such as adjusting preservative
application on the go and counting total pounds of product used.
Manual Mode: Allows operator to manually turn pumps on and off. This mode also has moisture content
displayed. Use this mode to prime pumps.
Software Versions: Selecting this tab will display the software currently installed.
Setup Mode: This mode allows the operator to adjust bale rate, application rate settings and select tip output.
Job Records: Keep track of up to 300 jobs with total product used, average moisture content, tons baled, and
baling date.

13
Screen Menus
Use the screen shots below to navigate through the operation screens.
Automatic Mode
Manual Mode
Operation Note:
Pressing the Home Button on the iPad WILL NOT immediately stop application of the System (see below):
Select or to stop application
*To close app see the Shutting Down Hay App Section
**When the app is not displayed for 10 seconds,
preservative application will stop.
Bluetooth Connection Indicator
Green
-DCP is connected
Yellow
-DCP connecting
Red
-DCP not connected
Bluetooth Connection Indicator
Green
-DCP is connected
Yellow
-DCP connecting
Red
-DCP not connected
X
-Pump is OFF
-Pump is ON

14
Setup Mode –Large Square Balers
*Only used if equipped with Tagger
NEEDSTO BEU PDATED
Turn Tagger ON by selecting the X
Indicates tagger is ON
*If RFV Equipped, additional options
will appear on Bale ID Screen (next)
If using RFV Spray Module,
turn ON by selecting the X
Indicates Spray Module is ON
Make sure Knotter/Dye Tip
Distance is correct
Select correct distance

15
Setup Mode –Large Square Baler (continued)
*Select X to turn on options shown
Indicates Crop Eyes are ON
*Only used if equipped with GPS
*Select grey area to change
*Select appropriate GPS unit
*Adjust alarm setting and turn on pump
module by selecting X in grey area
indicates Pump Module is on
Select correct tip setting
*High tips are installed from factory
Press OK if correct tip output
has been selected

16
Setup Mode –Large Square Baler (continued)
*Select correct bale weight, length,
and time per bale information
*Turn on Bale Rate sensor,
Green bar indicates sensors are ON
*Ensure all baler sensors are turned OFF
*If using a scale kit, turn sensor ON

17
Setup Mode –Large Square Baler (If RFV Equipped)
*Select correct bale weight, length,
and time per bale inforation
*Turn on Bale Rate sensor,
Green bar indicates sensors are ON
*Select correct bale size
Software Versions
*Versions shown are examples
(will not match your applicator)

18
Job Records
Type desired Field Name, select Create Job
*When RFV Equipped, Average RFV, Ave
TDN/CA90% info will be added
For Bale details select Bale
Button
Use arrows to change jobs shown

19
Job Records (continued)
Select Download when wanting to
download job records to USB Stick
Use arrows to change jobs shown.
Indicates selected jobs
Pressing the Select or Select All tab to
choose which job to download or delete
The Export allows you to send an email a
file with selected job records
When the Export page is opened the bale
information in each job will be retrieved.
When all bales have been retrived, Export
tab will activate, select a job(s) to export
If choosing one job to email, select the
Mail tab. Mulitple jobs can be selected
Email will appear w/file attached, enter address
*If two or more jobs selected, email will appear
Press the Send button in top right corner,
(your iPad notification sound will play)
If choosing to view job on iPad,
recommended to download Excel app to
view job records information
After Excel app is selected, the job
record spreadsheet will open
*iPad can only view 1 job at a time.
To save the job, select Name
from the drop down tab
Enter desired name in center of page and
press Save on the top right corner
After selecting Save, the list of saved files in
Excel will appear. Select any job to view
You also can view the jobs saved by selecting
Open tab after opening the Excel app

20
First Time and Annual Startup Instructions –Large Square Balers
THE UNIT MUST BE CHECKED OUT BEFORE FIELD OPERATION!
Check and Prime the Pumps
1. Put 10 gal (5L) of water in tank and turn main ball valve on.
2. Inspect for any leaks or drips at this time. If any are found tighten or replace area or fitting.
3. Press the SETUP MODE key. Turn bale rate sensors off (Figure 1). Make sure the AVG Bale Weight is
1500 lbs (680kg) and the AVG Baler Length is 96” (243cm), Time per bale is 60 seconds, and press the
MAIN MENU key to return to the opening screen.
4. Press the MANUAL MODE key and the screen will appear.
If RFV Equipped
Figure 1
Figure 2
Figure 3
Note: The system comes with the tips already installed on the spray shield or nozzle tubes.
Pump
Low Output
(Lbs / Ton) (L/MT)
High Output
(Lbs / Ton) (L/MT)
1
1.1 –1.5 (.5 - .7L)
1.9 –2.6 (.9 - 1.2L)
2
1.9 –2.6 (.9 - 1.2L)
2.9 –3.9 (1.3 - 1.8L)
3
2.9 –3.9 (1.3 - 1.8L)
5.7 –7.7 (2.6 - 3.5L)
5. Turn pump 1 on (P1). To turn the pump on, select the colored box next to P1 and change the
‘X’ to a check mark. Repeat the process for pumps 2 and 3 (P2 and P3).
6. This process will also be used to prime the pumps whenever needed.
7. While running pumps check for a good spray pattern out of the respective tips and verify that
no parts of the system are leaking.
8. While doing these tests the Volume Used on the bottom of the screen will be increasing, this
verifies that the flow meter is functioning.
9. The DCP button displays your connection signal with the Bluetooth receiver. Green –DCP is
connected, Yellow –DCP is connecting, Red –DCP not connected. Pressing MAIN MENU key
to return to the initial startup screen.
10.If your applicator is RFV equipped (figure 3), the RFV value of the last bale will be displayed
next to the last bale moisture reading.
8
9
5
10