Harvest TEC 547C User manual

#010-547C-14-INST
5/22
Installation Manual
MODEL 547C
55 Gallon Automatic Preservative Applicators
Forage Harvester

2
(intentionally blank)

3
Harvest Tec 547C Installation Table of Contents
Page
Introduction
4
Tools Needed
4
Installation of Applicator
5-29
1. Installation of Tank and Saddle
4 x 5
4 x 6
5 x 5
5 x 6
5-10
7
8
9
10
2. Mounting Front Pumping Plate Support
11
3. Mounting Rear Pump Plate Support
4 x 5
4 x 6
5 x 5
5 x 6
12-20
13-14
15-16
17-18
19-20
4. Installation of Spray Nozzles
21
5. Installation of Drain Fill Kit
22
6. Installation of Plumbing
23
7. Installation of Moisture Sensor Pads and Disks
24-25
8. Installation of the Controls
26
9. Installation of the Bale Rate Sensor
10. Installation of the Power Cable and Main Wiring Harnesses
27
28-30
System Wiring Diagram
28
Pin Outs
29-30
Parts Breakdowns
31-37
Tank and Saddle
31
Drain Fill Kit
32
Pump Manifold
33
Moisture Sensors and Hoses
34
Control Box and Wiring Harnesses
35
Model 547C Installation Kit
36
Warranty Statement

4
Introduction
Thank you for purchasing this 547C Hay Preservative Applicator System for your Round Baler. Please read
this manual carefully to ensure correct steps are followed when attaching the applicator to the baler. This
applicator is designed to apply Harvest Tec buffered propionic acid. The model 547C base kit includes the
following parts: Tank, Frame, Pumps, Hose, Baler Mounted Processor, Touchscreen Display, Moisture
Sensors, and Miscellaneous Hardware. The applicator can be installed on the Round Balers with the proper
installation kit. Before installing the unit on the baler, make sure you have the proper installation kit. (See the
chart below.) If you are unsure about your installation kit please contact your local authorized dealer for
specifications. For your convenience we have included a parts break down for the model 547C Hay
Preservative Applicator System.
Left and Right sides are determined by facing in the direction of forward travel.
Tools Needed
Standard wrench set
Side cutter
Standard screw driver or 5/16” nut driver
Hose cutter
SAE sock set
Hammer
Drill bit set
Crescent wrench
Center punch
Level

5
Installation of the Applicator
1. Installation of Tank and Saddle
a. Locate the left saddle leg, 001-4703XL, and mount to left side sheet of baler using two ½” x 1-1/2”
hex bolts, ½” lock washers, and ½” flat washers. Do not fully tighten.
b. Locate the right saddle leg, 001-4703XR, and mount to right side sheet of baler using two ½” x 1-
1/2” hex bolts, ½” lock washers, and ½” flat washers. Do not fully tighten.
c. Roll Belt 180/460 and RB465 Installation only! Locate the two anchor extension brackets, 001-
4703XAX, and attach one extension bracket to the outside of each leg with two ½” x 1-1/2” hex
bolts, ½” lock washers, and ½” flat washers.
d. Locate the anchor bracket, 001-4703XA, and attach to the side of the extension bracket, 001-
4703XAX for 4 X 6 balers (or 001-4703XR and 001-4703XL for other balers) using two ½” x 1-
1/2” hex bolts, ½” flat washers, ½” lock washers, and ½” hex nuts. Do not fully tighten. Note that
001-4703XA should be positioned so it is angled toward the round pipe that runs across the width
of the baler behind the legs. Repeat procedure for the opposite side.
e. Locate the u-bolts, 001-4703XAB, and attach the 001-4703XA brackets to the round pipe running
across the baler. Tighten the u-bolts evenly. **Due to minimal clearance between the anchor
bracket and the side sheet, use a deep socket and long extension on a ratchet to tighten the u-
bolts.
f. With the u-bolts, 001-4703XAB, securely tightened around the round pipe, tighten the bolts
connecting the anchor brackets, 001-4703XA, to the saddle legs, 001-4703XL & 001-4703XR.
g. Tighten the hardware attaching the saddle legs, 001-4703XL & 001-4703XR, to the side sheets of
the baler.
h. Install the tank assembly (tanks, straps, handrail, and saddle pan) on the legs. Secure the saddle
pan, 001-4703X, to the saddle legs with ½” flat washer, ½” lock washer, and ½” hex nut from the
bottom side in four locations. Tighten hardware.
The following pages contain additional illustration for mounting on your baler
4 X 5 pg 7
4 X 6 pg 8
5 X 5 pg 9
5 X 6 pg 10

6
001-4402
(x2)
001-6707HR
(x1)
001-4703XR
(x1)
001-4703XAB
(x2)
001-4703XAX
(x2)
001-4703XA
(x2)
001-4703XL
(x1)
001-9203SQ
**001-4703XAX (x2) are ONLY used on 4x6 models

7
4x5 Baler
4x5 Baler Exploded
4x5 Baler

8
4x6 Baler
4x6 Baler Exploded
4x6 Baler

9
5x5 Baler
5x5 Baler Exploded
5x5 Baler

10
5x6 Baler
5x6 Baler Exploded
5x6 Baler

11
2. Mounting Front Pump Plate Support
a. Open right side door of baler.
b. Locate mounting holes for your size baler in bracket (001-4703XE). Mount bracket to pre-
stamped square holes on diagonal support structure of baler. Note pictures on following pages will
help in locating the pre-stamped holes on your baler. Secure with two M8 x 25mm carriage bolts
and flanged nuts.
c. Disconnect pump mounting bracket (001-4646C) from pump plate by removing four 3/8” x 3/8”
flange bolts. Attach right top corner of pump mounting bracket to bracket (001-4703XE) with two
3/8” x 1” hex bolts, flat washers, lock washers, and nuts. Note: top of both brackets should be
flush.
001-4646C Pump
Mounting Plate Holes
4x6 and 5x6
Baler
Mounting Holes
4x5 and 5x5
Baler
Mounting Holes
001-4703XE
Figure 1

12
3. Mounting Rear Pump Plate Support
Mounting bracket (001-4703XF) will be used to mount the pump mounting bracket to the door support bracket.
However each size baler uses a different set of holes in the rear mounting bracket (001-4703XR). Follow the
guidance provided below as well as the additional instructions on the next few pages for mounting on your
size baler.
Figure 2

13
Mounting Rear Pump Plate Support for 4 X 5 Baler
1. Locate the baler door support bracket. This will be to the left of the Mounting Plate (001-4646C).
2. Use two 3/8” x 1” hex bolts, flat washers, lock washers, and nuts to secure Pump Plate Bracket
(001-4703XF) to back side of Pump Mounting Bracket (001-4646C). Use holes 1 and 2 as
designated in Figure 2 on the Pump Plate Bracket (001-4703XF). Slide the Pump Plate Bracket
(001-4703XF) so it touches the door support bracket.
3. Place a level on top of the Mounting Plate (001-4646C) to make sure it is level. Using the Pump
Plate Bracket (001-4703XF) as a guide mark holes (D and E) on the door support bracket.
Remove brackets (001-4703XF and 001-4646C) for drilling. Center punch holes and drill with a
7/16” drill bit.
4. Once holes are drilled secure (001-4703XF) to door support bracket with two 3/8” x 1” hex bolts,
flat washers, lock washers, and nuts.
5. Attach pump mounting bracket back onto brackets (001-4703XF and 001-4703XE) with 3/8”
hardware.
6. Attach pump plate with pumps onto Mounting Plate (001-4646C) bracket with 3/8” x ¾” flange bolts
removed earlier.
7. Install pump controller (006-5672) into pump plate using 5/16” flat washers, lock washers, and
nuts.
The Pump Controller and pump heads must be pointing down. Failure to mount the pump plate
assembly in this specified direction will void all warranty of the Pump Controller and pumps.
1.

14

15
Mounting Rear Pump Plate Support for the 4 x 6 Baler
1. Locate the baler door support bracket. This will be to the left of the Mounting Plate (001-4646C).
2. Use two 3/8” x 1” hex bolts, flat washers, lock washers, and nuts to secure Pump Plate Bracket
(001-4703XF) to back side of Pump Mounting Bracket (001-4646C). Use holes 3 and 4 as
designated in Figure 2 on the Pump Plate Bracket (001-4703XF). Slide the Pump Plate Bracket
(001-4703XF) so it touches the door support bracket.
3. Place a level on top of the Mounting Plate (001-4646C) to make sure it is level. Using the Pump
Plate Bracket (001-4703XF) as a guide mark holes (A and B) on the door support bracket.
Remove brackets (001-4703XF and 001-4646C) for drilling. Center punch holes and drill with a
7/16” drill bit.
4. Once holes are drilled secure (001-4703XF) to door support bracket with two 3/8” x 1” hex bolts,
flat washers, lock washers, and nuts.
5. Attach pump mounting bracket back onto brackets (001-4703XF and 001-4703XE) with 3/8”
hardware.
6. Attach pump plate with pumps onto Mounting Plate (001-4646C) bracket with 3/8” x ¾” flange bolts
removed earlier.
7. Install Pump Controller (006-5672) into pump plate using 5/16” flat washers, lock washers, and
nuts.
The Pump Controller and pump heads must be pointing down. Failure to mount the pump plate
assembly in this specified direction will void all warranty of the Pump Controller and pumps.

16

17
Mounting Rear Pump Plate Support for the 5 x 5 Baler
1. Locate the baler door support bracket. This will be to the left of the Mounting Plate (001-4646C).
2. Use two 3/8” x 1” hex bolts, flat washers, lock washers, and nuts to secure Pump Plate Bracket
(001-4703XF) to back side of Pump Mounting Bracket (001-4646C). Use holes 1 and 2 as
designated in Figure 2 on the Pump Plate Bracket (001-4703XF). Slide the Pump Plate Bracket
(001-4703XF) so it touches the door support bracket.
3. Place a level on top of the Mounting Plate (001-4646C) to make sure it is level. Using the Pump
Plate Bracket (001-4703XF) as a guide mark holes (C and E) on the door support bracket.
Remove brackets (001-4703XF and 001-4646C) for drilling. Center punch holes and drill with a
7/16” drill bit.
4. Once holes are drilled secure (001-4703XF) to door support bracket with two 3/8” x 1” hex bolts,
flat washers, lock washers, and nuts.
5. Attach pump mounting bracket back onto brackets (001-4703XF and 001-4703XE) with 3/8”
hardware.
6. Attach pump plate with pumps onto Mounting Plate (001-4646C) bracket with 3/8” x ¾” flange bolts
removed earlier.
7. Install Pump Controller (006-5672) into pump plate using 5/16” flat washers, lock washers, and
nuts.
The Pump Controller and pump heads must be pointing down. Failure to mount the pump plate
assembly in this specified direction will void all warranty of the Pump Controller and pumps.

18

19
Mounting Rear Pump Plate Support for the 5 x 6 Baler
1. Locate the baler door support bracket. This will be to the left of the Mounting Plate (001-4646C).
2. Use two 3/8” x 1” hex bolts, flat washers, lock washers, and nuts to secure Pump Plate Bracket
(001-4703XF) to back side of Pump Mounting Bracket (001-4646C). Use holes 3 and 4 as
designated in Figure 2 on the Pump Plate Bracket (001-4703XF). Slide the Pump Plate Bracket
(001-4703XF) so it touches the door support bracket.
3. Place a level on top of the Mounting Plate (001-4646C) to make sure it is level. Using the Pump
Plate Bracket (001-4703XF) as a guide mark holes (A and E) on the door support bracket.
Remove brackets (001-4703XF and 001-4646C) for drilling. Center punch holes and drill with a
7/16” drill bit.
4. Once holes are drilled secure (001-4703XF) to door support bracket with two 3/8” x 1” hex bolts,
flat washers, lock washers, and nuts.
5. Attach pump mounting bracket back onto brackets (001-4703XF and 001-4703XE) with 3/8”
hardware.
6. Attach pump plate with pumps onto Mounting Plate (001-4646C) bracket with 3/8” x ¾” flange bolts
removed earlier.
7. Install Pump Controller (006-5672) into pump plate using 5/16” flat washers, lock washers, and
nuts.
The Pump Controller and pump heads must be pointing down. Failure to mount the pump plate
assembly in this specified direction will void all warranty of the Pump Controller and pumps.

20