Haws H1001.8HPSHO User manual

model H1001.8HPSHO
FEATURES & BENEFITS
Rugged ADA accessible 18 gauge Type 304 high polished
Stainless Steel swirl design bowl, 14 gauge Type
304 high polished Stainless Steel bracket, and a
vandal-resistant bottom plate provides a long lasting
unit with added peace of mind.
QUALITY CONTROL
Pre-built fountain is pressure tested to ensure no leaks and
proper functionality.
MOUNTING
Heavy-duty 16-gauge galvanized steel mounting frame
with welded-in heavy-duty 10 gauge mounting plate with
pre-punched mounting holes. Further convenience is given
to the chiller with the integral fold-out shelf.
BUBBLER HEAD
Polished chrome-plated brass bubbler head with integral
laminar flow prevents splashing while providing a superior
flow pattern. The integral 11/16" dia. basin shank and
stainless anti-rotation roll pin for vandal resistance strength.
Shielded, angled stream opening provides a steady source
of drinking water at .45 gpm.
DRINKING FOUNTAIN VALVE
Fountain incorporates a touchless sensor operated stainless
steel solenoid valve controlled by a transformer for hands-
free operation. A pressure regulator is used to adjust the
bubbler flow according to incoming water pressures.
OPTIONS
Bottle Filler: Model 1920HOHPS, touchless bottle filler
can be a stand-alone station, or mounted above
Haws 1001HPS and 1011HPS series drinking fountain
models.
Back Panel: Model BP15HPS, high polished stainless
steel 15 inch back panel for Model 1920.
Water Filter: Model 6426, 10" x 2" (25.4 x 5.1 cm), in-line lead
removal element that reduces lead from incoming
water supply.
For more information, visit www.hawsco.com or call (888)
640-4297.
SPECIFICATIONS
Model H1001.8HPSHO vandal-resistant electric ADA wall
mounted motion-activated drinking fountain shall include an 18
gauge Type 304 polished stainless steel basin with integral
swirl design, 14 gauge Type 304 polished stainless steel wall
bracket, 100% lead-free waterways, touchless sensor
operated stainless steel solenoid valve with 30-second
obstruction time-out controlled by a transformer, polished
chrome-plated brass vandal-resistant bubbler head with
integral laminar anti-squirt flow, chrome-plated brass vandal
resistant waste strainer, vandal-resistant bottom plate,
polished stainless steel back panel and louvered
intrusion-proof grill, and 1-1/4" O.D. (3.2 cm) waste pipe.
The R-134a refrigeration system is hermetically sealed
and delivers a minimum of 8 gph (30.3 L) of water at 50° F
(10° C) cooled from 80° F (26.7° C) inlet water at 90° F (32.2° C)
ambient. 115 Volts, 60Hz, rated watts: 370, full load amps: 5
REQUIRES MODEL HCR8 AND MTGFR.SM PRICED SEPARATELY.
APPLICATIONS
This series is precisely mounted, making it a nice addition to
any surrounding. Specifically, this type fountain may be
placed in settings such as: schools, office buildings, shopping
malls, and other indoor environments where there is a
demand for a chilled water source and/or wheelchair
access. Electric water coolers are not recommended or
designed for outdoor applications or enclosed pool areas
(chlorine). These conditions may void warranty. Model meets
all current Federal Regulations for the disabled including those
in the Americans with Disabilities Act. Haws manufactures
drinking fountains, faucets and electric water coolers to be
lead-free by all known definitions including NSF/ANSI/CAN 61-
Section 9, NSF/ANSI/CAN 372, California Proposition 65, and
the Federal Safe Drinking Water Act. Product is compliant to
California Health and Safety Code 116875 (AB 1953-2006),
and NSF/ANSI/CAN 61: Q ≤ 1. Haws electric water coolers
comply with ARI Standard 1010 and ANSI A117.1, and are
listed by Underwriter Laboratories to U.S. and Canadian
standards.
1455 Kleppe Lane :: Sparks, NV 89431 :: p. 775.359.4712 :: f. 775.359.7424 :: e. [email protected] :: www.hawsco.com :: 20 July, 2022
DISCLAIMER: Continued product improvements make specifications subject to change without notice. Check www.hawsco.com for the latest product information and updates.
Chilled Vandal-Resistant ADA Motion-Activated High Polished Fountain
HANDS FREE
Touchless operation for safety and peace of mind.
CONSTRUCTION
FOR INDOOR USE ONLY
TAMPER RESISTANT
30-second obstruction time-out to reduce tampering of
sensor.
VANDAL-RESISTANT
The bubbler head, push button, round bowl, drain strainer
and bottom plate are locked in place, discouraging
unwanted vandal tampering.

FRAME FLANGE BUTTS BE INSTALLED SO THAT MOUNTING FRAME MUST IMPORTANT:
PANEL
BACK
FLANGE
FRAME
FACE WALL
473mm
18-5/8"
76mm
3"
27"
686mm
864mm
34"
LINE
FLOOR
15"
381mm
REINSTALL VALVE & ADJUST
FLOW.
WASTE ELBOW IS INSTALLED, REMOVE VALVE FROM PUSH BUTTON TO INSTALL WASTE ELBOW ONTO BOWL. AFTER
PANEL
BACK
(SUPPLIED)
SCREW
SHEET METAL
2X
INSIDE OF FRAME
(SUPPLIED)
MOUNTING CLIP
2X
GRILLE
(SUPPLIED)
FRAME
MOUNTING
SCREW
(SUPPLIED)
MACHINE
2X
15.9mm
5/8"
864mm
34"
(SUPPLIED)
GRILLE
CHILLER SUPPORT TRAY
ELECTRICAL
MOUNTING
WIDTH
FRAME
101.6mm
4"
WASTE BEND
(SUPPLIED)
ACCESS
708mm
27-7/8"
1-1/4" IPS TRAP
SUPPLY STOP &
3/8" O.D. TUBING
(NOT SUPPLIED)
FRAME
MOUNTING
13mm
1/2"
3/8" O.D.
TUBING,
INSULATION & FITTINGS
2X
MOUNTING
(SUPPLIED)
CLIP
(SUPPLIED)
Ø14-1/8"
359mm
(NOT SUPPLIED)
WASTE BEND
1-1/4" O.D.
44mm
1-3/4"
28-11/16"
729mm
FOUNTAIN
WASTE
SUPPLY
FOUNTAIN
MTGFR.SM
1. HOLD ROUGH-IN DIMENSIONS ±1/8" (3.2mm).
2. WHEN INSTALLING THIS UNIT, LOCAL, STATE, OR FEDERAL CODES SHOULD BE
ADHERED TO. FOR DIMENSIONS (LOCATIONS), WASTE AND SUPPLY REQUIREMENTS OTHER THAN SHOWN, DIMENSIONS MARKED (*) MUST BE ADJUSTED ACCORDINGLY.
3. INSTALLER MUST PROVIDE TRAP FOR PROPER INSTALLATION.
4 REFER TO 5874SS OPERATION AND MAINTENANCE MANUAL FOR
PUSH BUTTON AND VALVE INSTALLATION/MAINTENANCE INSTRUCTIONS.
5 REFER TO MTGFR.SM INSTALLATION DRAWING FOR ROUGH-IN DIMENSIONS. 6 INSERT 5/16"-18 PANEL INSERTS FROM OPPOSITE SIDE AT LOCATIONS SHOWN BY
DARKENED HOLES.
7 FOUNTAIN REMOVAL: FIRST REMOVE SCREWS AND THEN SQUEEZE CLIPS ON NUT
RETAINER TO POP OUT. INSTALL IS REVERSE OF REMOVAL.
8 ALIGN HOLES IN CHILLER SUPPORT TRAY WITH HOLES IN FRAME AND FASTEN WITH
#10 SHEET METAL SCREWS.
NOTES:
4
5
5
AGAINST FINISHED WALL FACE.
BOWL MOUNTING PATTERN DETAIL
7
6
SCREW
7
305mm
12"
359mm
14-1/8"
32-1/8"
816mm
INLINE STRAINER,
1/4" OD TUBE X
3/8" OD TUBE
INLET (SUPPLIED)
35mm
1-3/8"
HCR8
CHILLER
8
*
*
*
*
5
*
*
ROUGH-IN
ROUGH-IN
CLEARANCE
(NOT SUPPLIED)
APPROVED: DRAWN:
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BY:ECN NO.
DATE:
DATE:
ECN:
REVISED PER
CHK'D.:
Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
RTM
07-01-97
20
0002080246.D
H1001.8/H1001.8HPS
1:15
11
FV
04/02/20
.
DP
INSTALLATION
5527
2020
FV
SOLD SEPARATELY
REQUIRED -
Available with hands off sensor in lieu of push button

1. HOLD ROUGH-IN DIMENSIONS ±1/8" (3.2mm).
2. WHEN INSTALLING THIS UNIT, LOCAL, STATE, OR FEDERAL
CODES SHOULD BE ADHERED TO FOR INSTALLATION
DIMENSIONS (LOCATIONS), WASTE AND SUPPLY REQUIREMENTS OTHER THAN SHOWN.
INSTALLER MUST PROVIDE TRAP FOR PROPER INSTALLATION. REFER TO 1RKHO.H OPERATION AND MAINTENANCE
INSTRUCTIONS FOR TRANSFORMER AND SENSOR SETUP.
NOTES:
3
4
BP6 BACK PANEL
(OPTIONAL)
TRAP ACCESS PANEL
MODEL 6603
(OPTIONAL)
Ø3/8" SUPPLY TUBING
(SUPPLIED)
SCREW DRIVER STOP
(NOT SHOWN) IS NOT
SUPPLIED
6700 MOUNTING PLATE
(BEHIND FINISH WALL)
MOUNTING BOLTS
(NOT SUPPLIED)
WASTE BEND AND
1-1/4" IPS TRAP
(NOT SUPPLIED)
A A
1 1/4" OD
WASTE BEND
(SUPPLIED)
6700 MOUNTING PLATE
MUST BE INSTALLED BEFORE FINISH WORK
THIS PLATE IS REQUIRED - SOLD SEPARATELY.
SECTION A-A
ROTATED 90° INTO VIEW
BRACKET MOUNTING
DETAIL
WALL FACE
FLOOR LINE
WALL STUD
WALL FACE
4X 3/8-16 UNC
[359]
ø14 1/8"
[406]
16"
[83]
3 1/4"
[133]
5 1/4"
[76]
3"
[47]
1 27/32"
[76]
3"
[10]
4X ø3/8"
[47]
1 27/32"
[25]
1"
[58]
2 9/32"
[51]
2"
[406]
16"
[457]
18"
[127]
5"
[178]
7"
[729]
28 11/16"
SUPPLY
[714]
28 3/32"
WASTE
[686]
27"
[864]
34"
(TO SPOUT
OUTLET)
[76]
3"
[473]
18 5/8"
[380]
15"
[645]
25 3/8"
11116" [42]
APPROVED: DRAWN:
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BY:ECN NO.
DATE:
DATE:
ECN:
REVISED PER
CHK'D.:
Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
FV
09/28/21
1
0510002020.D
1001HO
1:1
11
FV
09/30/21
BJM
INSTALLATION
5733
2021
FV
LOCATE AND INSTALL ELECTRICAL
9VDC SOLENOID VALVE
TRANSFORMER WITHIN WALL
SENSOR
EYE
4
SUPPLY LINE
SENSOR
FROM SUPPLY
TO
BUBBLER
HEAD
-Vo
+Vo
AC(L)
AC(N)
BLACK WIRE
WHITE WIRE
TRANSFORMER
SENSOR WIRING / SUPPLY PLUMBING
SCHEMATIC
SOLENOID
VALVE
Y-STRAINER
PRESSURE
REGULATOR
(Y-STRAINER NOT SHOWN)
3
100-277VAC-9VDC
TRANSFORMER
AND DC CABLE
(SUPPLIED)
FROM DIRECT
CONTACT WITH WATER
MUST BE PROTECTED
4
Y-STRAINER
(SUPPLIED)
4
9" [228]
REGULATOR
3