Haws 1311 Guide

11/17 Model 1311 Page 1 of 5
No. 0510000046 (4)
1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]
E-mail: [e-mail]  website: www.hawsco.com
Model 1311
Drinking Fountain
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
LIMITED WARRANTY
HAWS
warrants that this specific product is guaranteed against defective material
or poor workmanship for a period of one year from date of shipment. HAWS
liability unde
r this warranty shall be discharged by furnishing without charge F.O.B.
HAWS Factory any goods, or part thereof, which shall appear to the Company upon
inspection to be of defective material or not of first class workmanship, provided that
claim is made in
writing to Haws within a reasonable period after receipt of the
product. Where claims for defects are made, the defective part or parts shall be
delivered to the Company, prepaid, for inspection. HAWS will not be liable for the
cost of repairs, alterations or replacements, or for any expense connected therewith
made by the owner or his agents, except upon written authority from HAWS,
Sparks, Nevada. HAWS will not be liable for any damages caused by defective
materials or poor workmanship, except for replacements, as provided above. Buyer
agrees that HAWS shall not be liable for general, special, or consequential
damages claimed to arise under the contract of sale. The drinking fountain
manufactured by HAWS is warranted to function if installation and maintenance
instructions provided are adhered to. The units also must be used for the purpose
for which they were intended.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297

11/17 Model 1311 Page 2 of 5
RECOMMENDED TOOLS: Hack saw, pipe joint sealant, screwdriver, level, 12" adjustable
wrench, 10" pipe wrench, 5/64” hex key wrench, 9/16”, 1/2”, 7/16” socket wrench or open
end wrench.
LOCATION OF UNIT: The Model 1311 Drinking Fountain is a wheelchair accessible
drinking water facility. The height dimensions shown, meet current ADA requirements.
When installing this unit, local, state or federal codes should be adhered to. If height other
than shown is required, then dimensions must be adjusted accordingly.
SUPPLY LINE: The minimum recommended line size is 1/2“IPS with 30-90 psi (2-6 ATM)
flowing pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.
PLUMBING CONNECTIONS: Inlet is 3/8” O.D. tubing fitting. Waste trap outlet is
1-1/4” IPS.
MAINTENANCE: Periodically clean the strainer. Refer to 5874 Series Valve Manual for
more information.
INSTALLATION PROCEDURE
GENERAL NOTES:
1. For all plastic push-in type fitting connections, only connect NSF-61 copper or
plastic tubing. Stainless steel or glass tubing is not recommended. The
following assembly instructions must be followed to ensure a watertight
connection:
a. Cut tubing square and clean.
b. Mark from end of tube the length of insertion (See table below).
c. Push tube into the fitting until it bottoms out.
d. To remove, depress collet and pull tubing out.
Tube Sizes
O.D.
Tolerance Insertion Depth
1/4”
±.005”
11/16”
3/8”
±.005”
3/4”
1/2”
±.005”
7/8”

11/17 Model 1311 Page 3 of 5
INSTALLATION PROCEDURE
Refer to Installation Drawing for mounting height. For steps below, refer to exploded
view.
STEP 1:Remove hex lock nut and washers from bubbler heads, set aside. Install bubbler
heads through receptor. Install respectively rubber washer, fiber washer, and then
nut onto bubbler shank. Securely tighten nut.
STEP 2:Remove push button assembly from 5874 Series Valve with spanner wrench
provided. Be sure to also remove (chrome plated) ring nut and (chrome plated)
washer from valve. At this point, carefully follow installation instructions shown on
page 5 of 5 of 5874 Series Valve/Push Button Operation and Maintenance
Manual under heading: “INSTALLATION INSTRUCTIONS FOR 5874 Series
Valve W/PBA6”.
STEP 3: Make tubing connections from bubbler to the outlet side of control valve. Follow
instructions for tubing preparation and insertion depths from Step 3.
STEP 4: Place strainer into receptor (using plumber’s putty), secure in place using a fiber
washer and lock nut.
STEP 5: Mount fountain with appropriate hardware as shown on Installation Drawing.
STEP 6: Flush supply line to clear debris. Connect to a 1/2” NPT supply line and tighten.
STEP 7: Make certain that fountain is level and well secured to wall. Connect waste trap to a
1-1/4” IPS waste pipe (to be supplied by customer).
STEP 8: Completely open the screwdriver stop (not supplied) and check for leaks.
STEP 9: Adjust valves for desired flow height. See 5874 Series Valve Manual (supplied).
STEP 10: Attach bottom plate to fountain using #10-24 hardware provided.
TROUBLESHOOTING
PROBLEM
REPAIR CHECKLIST
1.
Insufficient bubbler flow.
1a.
Check that inlet screwdriver stop valve is in
wide-open position.
b.
Verify minimum 30 psi flowing supply pressure.
c.
Clean strainer. See 5874 Series Valve
Manual.
d.
Adjust valve to increase flow. Use front adjust
screw or see 5874 Series Valve Manual.
For more information on Haws Products, please see our website: www.hawsco.com
© 2017 Haws®Corporation – All Rights Reserved
HAWS® and other trademarks usedin these materials are the exclusive property of Haws Corporation.

2X 10-24 SCREW
STRAINER ASSEMBLY 6453
(NUTS AND WASHERS
INCLUDED)
1-1/4 X 1/2 X 1/8
RUBBER WASHER
1-1/4 X 11/16 X 1/8
FIBRE WASHER
3/8 HEX LOCK NUT
5703M BUBBLER
4
1-13/16 X 1.73 X .12
NEOPRENE WASHER
1-3/4 X 1-5/16 X 3/32
FIBER WASHER
LOCK NUT 1 REQD
5874PBF VALVE 1
PARTS BREAKDOWN
BUBBLER)
(ASSEMBLED TO
CLEAR POLY TUBING
(ASSEMBLED TO BUBBLER)
5703M BUBBLER INSERT
DETAIL OF 5703M
ROTATED 90° CCW
VIEW A
A
DRIVER, NOZZLE
.25 HEX PN
0002082253
(OPTIONAL) FOR
REMOVAL OF
NOZZLE WITH TUBE
HAWS PN 6700
OPTIONAL MOUNTING PLATE
1-1/4" WASTE TRAP
LOW PROFILE
NOTES:
1 APPLY ONE DOT OF LOCTITE 222MS THREADLOCKER ON FEMALE
THREADS OF PUSH BUTTON. SEE 5874 SERIES OPERATION AND
MAINTENANCE MANUAL (PAGE 5 OF 5) FOR PROPER APPLICATION
PROCEDURE.
2 5874PBF INCLUDES VRK5874 CARTRIDGE ASSEMBLY AND PBA6 FLANGED
PUSHBUTTON.
3 REFER TO 5874 SERIES OPERATION AND MAINTENANCE MANUAL FOR
INSTALLATION INSTRUCTIONS.
4 CONNECT CLEAR "POLYETHYLENE" TUBING ON FREE FLOW SIDE
(VALVE TO BUBBLER HEAD) ONLY.
PBM1311ADA
BOTTOM PLATE
APPROVED
DRAWN
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BYECN NO.
PAGE
DATE
DATE
ECN:
REVISED PER
CHKD
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
HM
08/25/15
4
0510000046
1311
1:4
11
FV 11/23/17
5010 GC
4 of 5
PARTS BREAKDOWN
5258
2017
WAVE WASHER
PBA6 PUSH BUTTON
1
ASSEMBLY
WASHER 1.98 X 1 1/4-18 UNEF X .10
POLISHED CHROME PLATE
2
10-24 HARDWARE)
2X ANCHOR (PART OF
3
(INCLUDES VRK5874
AND PBA6)
2

13 1/4"
337mm
3 1/2"
MTG HOLES
MOUNTING DETAIL
699mm
*27 1/2"
102mm
4"
4X Ø 14mm
9/16"
89mm
3 1/2"
13mm
1/2"
4"
102mm
89mm
7"
MOUNTING PLATE
(HAWS 6700)
178mm
152mm
6"
16"
406mm
FLOOR LINE
(OPTIONAL)
2"
51mm
9.5mm
3/8" 4X Ø
4X 3/8"-16 UNC
FLOOR LINE
WALL STUD
16"
406mm
MOUNTING BOLTS
(NOT SUPPLIED)
UP FTN SIDE
SUPPLY
4X 3/8"-16 MOUNTING HARDWARE
(NOT SUPPLIED)
OPTIONAL 6700
MTG PLATE
686mm
*32 3/4"
832mm
*27"
WALL FACE
FLOOR LINE
LOW PROFILE
1-1/4" TRAP
2 3/4"
70mm
18"
457mm
SUPPLY
*29"
737mm
WASTE
746mm
*29 3/8"
(NOT SUPPLIED)
SCREWDRIVER STOP
3/8" O.D. TUBING &
(SUPPLIED)
3
WASTE
PIPE
SUPPLY
TUBE
1. HOLD ROUGH-IN DIMENSIONS ± 1/4" (6.4MM).
2. WHEN INSTALLING THIS UNIT, LOCAL, STATE, OR FEDERAL CODES SHOULD
BE ADHERED TO. FOR INSTALATION HEIGHTS OTHER THAN SHOWN,
DIMENSIONS MARKED (*) MUST BE ADJUSTED ACCORDINGLY.
3 REFER TO 5874 SERIES VALVE OPERATION AND MAINTENANCE MANUAL FOR
PUSH BUTTON AND VALVE INSTALLATION/MAINTENANCE INSTRUCTIONS.
APPROVED:
DRAWN:
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BY:ECN NO.
PAGE
DATE:
DATE:
ECN:
REVISED PER
CHK'D.:
Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
HM
08/25/15
4
0510000046.D
1311
1:14
11
FV 11/23/17
5010
GC
5 of 5
INSTALLATION
5258
2017
JP
679mm
*26 3/4"
18"
9 1/8"
232 mm
457mm
7"
178mm