Haws 3150 Guide

09/14 Model 3150 Page 1 of 5
1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]
E-mail: [email protected] website: www.hawsco.com
Model 3150
Drinking Fountain
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
No. 2077070(24)
LIMITED WARRANTY
HAWS warrants that this specific product is guaranteed against defective material or
poor workmanship for a period of one year from date of shipment. HAWS liability
under this warranty shall be discharged by furnishing without charge F.O.B. HAWS
Factory any goods, or part thereof, which shall appear to the Company upon
inspection to be of defective material or not of first class workmanship, provided that
claim is made in writing to Haws within a reasonable period after receipt of the
product. Where claims for defects are made, the defective part or parts shall be
delivered to the Company, prepaid, for inspection. HAWS will not be liable for the
cost of repairs, alterations or replacements, or for any expense connected therewith
made by the owner or his agents, except upon written authority from HAWS, Sparks,
Nevada. HAWS will not be liable for any damages caused by defective materials or
poor workmanship, except for replacements, as provided above. Buyer agrees that
HAWS shall not be liable for general, special, or consequential damages claimed to
arise under the contract of sale. The drinking fountain manufactured by HAWS is
warranted to function if installation and maintenance instructions provided are
adhered to. The units also must be used for the purpose for which they were
intended.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297

09/14 Model 3150 Page 2 of 5
RECOMMENDED TOOLS: Hack saw, pipe joint sealant, screwdriver, level, 12" adjustable
wrench, 10" pipe wrench, 5/64” hex key wrench, 9/16”, 1/2", 7/16” socket wrench or open
end wrench.
LOCATION OF UNIT: The Model 3150 Drinking Fountain is a wheelchair accessible
drinking water facility. The height dimensions shown, meet current ADA requirements.
When installing this unit, local, state or federal codes should be adhered to. If height other
than shown is required, then dimensions must be adjusted accordingly.
SUPPLY LINE: The minimum recommended line size is 1/2“IPS with 30-90 psi (2-6 ATM)
flowing pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.
PLUMBING CONNECTIONS: Inlet is 1/4" IPS male fitting. Waste outlet is female 1-1/2”
Slip PVC.
MAINTENANCE: Periodically clean the strainer. Refer to 5874SS Valve Operation and
Maintenance Sheet for more information.
TROUBLESHOOTING
PROBLEM REPAIR CHECKLIST
1. Insufficient bubbler flow. 1a. Check that inlet screwdriver stop
valve is wide open. Turn
counterclockwise.
b. Verify minimum 30 psi flowing supply
pressure.
c. Clean strainer. See 5874SS Valve
Manual.
d. Adjust valve to increase flow. Use
front adjust screw or see 5874SS
Valve Manual.
General Notes:
Before tightening nut and ferrule assembly, push tubing into fitting until it bottoms out
to ensure correct engagement with O-Ring.
For more information on Haws Products, please see our website: www.hawsco.com
© 2014 Haws Corporation – All Rights Reserved
HAWS® and other trademarks usedin these materials are the exclusive property of Haws Corporation.

1
2BOTTOM PLATE
3STRAINER ASSY
4
BUBBLER HEAD
5PUSH BTN ASS'Y
6VALVE
4
5
1
3
7
ACCES PLATE SST W/HOLE (OPTIONAL)
4
5
3
7
OPTIONAL
2
ROTATED 90° INTO VIEW
DETAIL OF ITEM 3
DETAIL A
A
PBM1047
6466
5703M
PBA7
5874SS
0004499489
6
BIB FAUCET, SELF CLOSING (OPTIONAL) 6250LF
*
*
ITEM 7 (ACCESS PLATE W/HOLE)
MUST BE USED WITH ITEM 8
(BIB FAUCET, SELF CLOSING).
OPTIONAL
** (OPTIONAL)
FOR REMOVAL OF
NOZZLE WITH TUBE
3/8" OD TUBING IS PART
OF BUBBLER HEAD AND
IS NOT REMOVABLE
** ENSURE TUBE IS DISCONNECTED FROM VALVE
BODY PRIOR TO REMOVAL. APPLY A DROP OF
LOCTITE 222MS ON NOZZLE THREADS PRIOR TO
REASSEMBLING BACK ONTO BUBBLER HEAD.
REATTACH TUBE TO VALVE BODY.
8
8
DRIVER, NOZZLE .25 HEX 0002082253
APPROVED
DRAWN
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BYECN NO.
PAGE
DATE
DATE
ECN:
REVISED PER
CHKD
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [e-mail]
WEBSITE: WWW.HAWSCO.COM
ITEM DESCRIPTION
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
PART NO.
D. OLLOM 11/25/95
24
0002077070
3150
1:4
11
FV 10/21/14
FV
3 of 5
PARTS BREAKDOWN
4933
2014
HM

RECESSED
ACCESS PLATES
40"
1016mm
13" 14-1/4"
362mm
WASTE (NOT SUPPLIED)
SCREWDRIVER STOP
(NOT SUPPLIED)
30" SQUARE CONCRETE
SLAB (NOT SUPPLIED)
1/2" IPS SUPPLY (NOT SUPPLIED)
FINISHED GRADE
1/2-13 UNC
ANCHORS
6"
152mm
MIN.
8"
203mm
MOUNTING HOLES FOR
1/2" ANCHOR BOLTS
203mm
8"
TO BUBBLER
VALVE INLET
1/2" IPS INLET
0004499489
(OPTIONAL)
CONCRETE PEDESTAL
SCREWDRIVER STOP, COMPRESSION FITTING,
330mm
MOUNTING PLATE
724mm
28-1/2"
CUT-AWAY VIEW
BRACKET
SEE DETAIL "A"
BOLTS
3/8" LOCK &
BRACKET
3/8-16X1
HEX HEAD
3/8" FLAT
WASHERS
ACCESS PLATE IN CONCRETE SLAB
4X
1/2-13 UNC
MTG BOLTS 4X
(SUPPLIED)
TEMPLATE
PEDESTAL
1-1/2 SLIP PVC
1054mm
41-1/2"
1 REFER TO 5874SS OPERATION AND MAINTENANCE MANUAL FOR
PUSH BUTTON AND VALVE INSTALLATION/MAINTENANCE INSTRUCTIONS.
1
(OPTIONAL)
MODEL 6250LF
(TO SPOUT
OUTLET)
BIB FAUCET
2 L-BRACKETS ARE PRE-ASSEMBLED AND
BE LOOSENED FOR ANY REASON.
NOTES CONTINUED ON SHEET 2 OF 2.
32-3/4"
832mm
18-1/2"
470mm
ADA HEIGHT (SEE
SHEET 2 OF 2 FOR
SHOWN AT ADULT
ACTUAL DIMENSIONS) 203mm
8"
1/2" NPT AND 3/8" O.D. TUBING (NOT SUPPLIED)
1/2" TUBING AND COMPRESSION FITTINGS
(NOT SUPPLIED)
1/2" NPT
ARM
2
23
(SUPPLIED)
2
2
2
(SUPPLIED)
1/2" NPT TEE
(SUPPLIED)
APPROVED: DRAWN:
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BY:ECN NO.
PAGE
DATE:
DATE:
ECN:
REVISED PER
CHK'D.:
Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
CJL
09/92
24
0002077070.D
3150
1:13
12
FV
10/21/14
FV
4 of 5
INSTALLATION
4933
2014
HM

A
B
FINISHED GRADE
TO SPOUT
STEP 1: ATTACH ENTIRE ARM ASSEMBLY TO MOUNTING PLATE ON PEDESTAL USING THE 3/8" -16 X 1" BOLTS AND WASHERS (SUPPLIED) AND TIGHTEN SECURELY IN PLACE. STEP 2: (OPTIONAL) APPLY CAULKING AS NEEDED TO FILL ANY GAP BETWEEN ARM AND PEDESTAL.
3 SIDE ARM IS ADJUSTABLE TO ACCOMODATE EITHER CHILD OR ADULT
HEIGHTS (SEE "AVAILABLE ARM HEIGHTS" CHART). 4 BASED ON DESIRED HEIGHT (CHILD OR ADULT) OF ARM, ORIENT BACKPLATE AS SHOWN IN FIGURE 1 AND USE APPROPRIATE SHADED HOLES.
5 WASTE ASSEMBLY IS SUPPLIED DISASSEMBLED. THE SHORTER OF THE
TWO PIECES IS FOR THE ARM DRAIN, AND MUST BE INSTALLED SO THAT ANY BEND IN THE FLEX TUBING WILL ALLOW WATER TO DRAIN COMPLETELY. THE LONGER IS FOR THE PEDESTAL DRAIN AND IS SUPPLIED AT THE LENGTH REQUIRED TO ASSEMBLE THE UNIT WITH THE ARM AT CHILD HEIGHT. IN ORDER TO ASSEMBLE AT ADULT HEIGHT, 3" MUST BE CUT FROM THE END OF THE FLEX TUBING PRIOR TO ASSEMBLY. TEE IS TO BE GLUED TO THE FLEX TUBING WASTE ARMS USING PVC PIPE CEMENT.
OUTLET
24" / 610mm
27" / 686mm
29-3/4" / 756mm
32-3/4" / 832mm
B
ACHILD ADA
ADULT ADADIM
CHILD ADULT
BACKPLATE
KNEE
CLEARANCE
AVAILABLE ARM HEIGHTS
(8")
4
4
5
APPROVED: DRAWN:
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BY:ECN NO.
PAGE
DATE:
DATE:
ECN:
REVISED PER
CHK'D.:
Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [e-mail]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
CJL
09/92
24
0002077070.D
3150
1:13
22
FV
10/21/14
FV
5 of 5
INSTALLATION
4933
2014
HM