HENNESSY INDUSTRIES Coats XR 1850 Series User manual

1601 J. P. Hennessy Drive, LaVergne, TN USA 37086-3565 615/641-7533 800/688-6359 www.ammcoats.com Manual Part No.: 8113423 07
HENNESSY INDUSTRIES INC. Manufacturer of AMMCO®, COATS®and BADA®Automotive Service Equipment and Tools. Revision: 01/07
®
READ these instructions before placing unit in
service KEEP these and other materials delivered
with the unit in a binder near the machine for
ease of reference by supervisors and operators.
See
Balancing
Your First Tire
on page 2.
XR 1800/1850 Series
Wheel Balancer
Installation Instructions
Operating Instructions
Safety Instructions
Maintenance Instructions

ii • Important: Always read and follow the on-screen operating instructions.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
READ ALL INSTRUCTIONS
1. Eye and face protection recommendations:
“Protective eye and face equipment is required to
be used where there is a reasonable probability of
injury that can be prevented by the use of such
equipment.” O.S.H.A. 1910.133(a) Protective gog-
gles, safety glasses, or a face shield must be pro-
vided by the owner and worn by the operator of
the equipment. Care should be taken to see that
all eye and face safety precautions are followed by
the operator. ALWAYS WEAR SAFETY GLASSES.
Everyday glasses only have impact resistant
lenses, they are not safety glasses.
2. Do not disable hood safety interlock system, or in
any way shortcut safety controls and operations.
3. Be sure that wheels are mounted properly, the hub
nut engages the arbor for not less than four (4)
turns, and the hub nut is firmly tightened before
spinning the wheel.
4. Read and understand this manual before operat-
ing. Abuse and misuse will shorten the functional
life.
5. Be sure the balancer is properly connected to the
power supply and electrically grounded.
6. Do not operate equipment with a damaged cord or
if the equipment has been dropped or damaged –
until it has been examined and repaired by a quali-
fied serviceman.
7. Do not let cord hang over edge of table, bench, or
counter or come in contact with hot manifolds or
moving fan blades.
8. If an extension cord is necessary, a cord with a cur-
rent rating equal to or more than that of the equip-
ment should be used. Cords rated for less current
than the equipment may overheat. Care should be
taken to arrange the cord so that it will not be
tripped over or pulled.
9. Keep guards and safety features in place and in
working order.
10. Wear proper clothing. Safety toe, non-slip
footwear and protective hair covering to contain
hair is recommended. Do not wear jewelry, loose
clothing, neckties, or gloves when operating the
balancer.
11. Keep work area clean and well lighted. Cluttered
and/or dark areas invite accidents.
12. Avoid dangerous environments. Do not use power
tools or electrical equipment in damp or wet loca-
tions, or expose them to rain.
13. Avoid unintentional starting. Be sure the balancer
is turned off and power disconnected before serv-
icing.
14. Disconnect the balancer before servicing.
15. Use only manufacturer’s recommended acces-
sories. Improper accessories may result in per-
sonal injury or property damage.
16. Repair or replace any part that is damaged or worn
and that may cause unsafe balancer operation. Do
not operate damaged equipment until it has been
examined by a qualified service technician.
17. Never overload or stand on the weight tray or any
part of the balancer.
18. Do not allow untrained persons to operate machin-
ery.
19. To reduce the risk of fire, do not operate equip-
ment in the vicinity of open containers or flamma-
ble liquids (gasoline).
20. Adequate ventilation should be provided when
working on or operating internal combustion
engines.
21. Keep hair, loose clothing, fingers, and all parts of
body away from moving parts.
22. Use equipment only as described in this manual.
23. Use only manufacturer’s recommended attach-
ments and accessories.
Safety

Important: Always read and follow the on-screen operating instructions. • iii
Owner’s Responsibility
To maintain machine and user safety, the responsibil-
ity of the owner is to read and follow these instruc-
tions:
• Follow all installation instructions.
• Make sure installation conforms to all applicable
Local, State, and Federal Codes, Rules, and
Regulations; such as State and Federal OSHA
Regulations and Electrical Codes.
• Carefully check the unit for correct initial function.
• Read and follow the safety instructions. Keep them
readily available for machine operators.
• Make certain all operators are properly trained,
know how to safely and correctly operate the unit,
and are properly supervised.
• Allow unit operation only with all parts in place and
operating safely.
• Carefully inspect the unit on a regular basis and
perform all maintenance as required.
• Service and maintain the unit only with authorized
or approved replacement parts.
• Keep all instructions permanently with the unit and
all decals/labels/notices on the unit clean and visi-
ble.
• Do not override safety features.
Operator Protective Equipment
Personal protective equipment helps make tire serv-
icing safer. However, equipment does not take the
place of safe operating practices. Always wear durable
work clothing during tire service activity. Loose fitting
clothing should be avoided. Tight fitting leather gloves
are recommended to protect operator’s hands when
handling worn tires and wheels. Sturdy leather work
shoes with steel toes and oil resistant soles should be
used by tire service personnel to help prevent injury in
typical shop activities. Eye protection is essential dur-
ing tire service activity. Safety glasses with side
shields, goggles, or face shields are acceptable. Back
belts provide support during lifting activities and are
also helpful in providing operator protection.
Consideration should also be given to the use of hear-
ing protection if tire service activity is performed in an
enclosed area, or if noise levels are high.
Definitions of Hazard Levels
Identify the hazard levels used in this manual with the
following definitions and signal words:
DANGER
Watch for this symbol:
It Means: Immediate hazards, which will result in
severe personal injury or death.
WARNING
Watch for this symbol:
It Means: Hazards or unsafe practices, which could
result in severe personal injury or death.
CAUTION
Watch for this symbol:
It Means: Hazards or unsafe practices, which may
result in minor personal injury or product or property
damage.
Watch for this symbol! It means BE ALERT! Your
safety, or the safety of others, is involved!
CAUTION
WARNING
DANGER
Safety

iv • Important: Always read and follow the on-screen operating instructions.
Safety
Safety Notices and Decals
Failure to follow danger, warning, and caution
instructions may lead to serious personal
injury or death to operator or bystander or
damage to property. Do not operate this
machine until you read and understand all the
dangers, warnings and cautions in this man-
ual. For additional copies of either, or further
information, contact:
Hennessy Industries, Inc.
1601 J.P. Hennessy Drive
LaVergne, TN 37086-3565
[phone] or [phone]
www.ammcoats.com
The Lateral Runout unit of this machine contains a
Class IIIa laser with a maximum output less than 5mW
at a wave length of 650-670 nm. Avoid Exposure -
Laser radiation is emitted from its aperture.
Use of controls, adjustments or performance
of procedures other than those specified
herein may result in hazardous radiation
exposure.
There are NO service procedures or adjust-
ments which can be performed on the laser
in this product.
In case of failure, the entire lateral runout unit
(part no. 80180126) must be replaced.
CAUTION
WARNING

Important: Always read and follow the on-screen operating instructions. • v
Standard Safety Devices
• Stop key for stopping the wheel under emergency
conditions.
• A hood guard of high impact plastic that is designed
to prevent the counterweights from flying out in any
direction except towards the floor.
• A hood switch interlock system that prevents the
machine from starting if the guard is not lowered and
stops the wheel whenever the guard is raised.
Safety

NOTICE
Read entire manual before assembling,
installing, operating, or servicing this
equipment.
vi • Important: Always read and follow the on-screen operating instructions.
Safety

Important: Always read and follow the on-screen operating instructions. • 1
Contents
TTaabblleeooffCCoonntteennttss
IImmppoorrttaannttSSaaffeettyyIInnssttrruuccttiioonnss........................iiii
Owner’s Responsibility . . . . . . . . . . . . . . . . . . . . . .iii
Operator Protective Equipment . . . . . . . . . . . . . . . .iii
Definitions of Hazard Levels . . . . . . . . . . . . . . . . . .iii
Safety Notices and Decals . . . . . . . . . . . . . . . . .iv - v
Standard Safety Devices . . . . . . . . . . . . . . . . . . . . .v
BBaallaanncciinnggYYoouurrFFiirrssttTTiirree........................22--33
PPrriinncciipplleeOOppeerraattiinnggPPaarrttss..................
..........44--99
Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Air Gauge Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Positioning Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Using the Offset Arm . . . . . . . . . . . . . . . . . . . . . . .7
Sensor Measuring Systems . . . . . . . . . . . . . . . . . . .8
Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
UUnnddeerrssttaannddiinnggtthhee
VViiddeeooDDiissppllaayySSccrreeeennss............................1100--1133
Monitor and Initial Screen Feature Reference . . . .11
Menu Screen Flowchart . . . . . . . . . . . . . . . . .12 - 13
BBaallaanncceerrFFuunnccttiioonn
SSeett--uuppaannddRReevviieeww..................................1144--1166
General Set-up . . . . . . . . . . . . . . . . . . . . . . . .14 - 15
Balancing Set-up . . . . . . . . . . . . . . . . . . . . . . . . .15
Special Functions . . . . . . . . . . . . . . . . . . . . . . . . . .15
Additional Functions . . . . . . . . . . . . . . . . . . . . . . . .16
AAddvvaanncceeddBBaallaanncciinnggFFuunnccttiioonnss..............1166--1199
Initial Screen Options . . . . . . . . . . . . . . . . . . .16 - 17
Dynamic Modes . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Static Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Special Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Additional Options . . . . . . . . . . . . . . . . . . . . . . . . .19
MMaattcchhiinngg..................................................2200--2222
Automatic Runout Detection . . . . . . . . . . . . . . . . .20
Optimization (Match Balance) . . . . . . . . . . . . . . . .21
Runout (Runout Match) . . . . . . . . . . . . . . . . . . . . .22
MMaannuuaallllyySSeettttiinnggWWhheeeell
DDiimmeennssiioonnss((DDIIMM))..........................................2233
MMoouunnttiinnggWWhheeeello
onnSSppiinnddlleeSShhaafftt........2244--2255
Standard Back Cone Mounting . . . . . . . . . . . . . . .24
Standard Front Cone Mounting . . . . . . . . . . . . . . .25
Alternate Mounting . . . . . . . . . . . . . . . . . . . . . . . .25
MMaacchhiinneeSSeellff--ccaalliibbrraattiioonnaanndd
SSeerrvviicceeAAddjjuussttmmeennttss..............................2266--2299
Machine Self-calibration . . . . . . . . . . . . . . . . . . . . .26
Service Adjustments . . . . . . . . . . . . . . . . . . . . . . .27
Distance Arm Calibration . . . . . . . . . . . . . . . . . . . .27
Width Sonar Calibration (If equipped) . . . . . . .27 - 28
Diameter Arm Calibration (Plastic) . . . . . . . . . . . . .28
Diameter Arm Calibration (Metal) . . . . . . . . . . . . .29
DDiiaaggnnoossttiiccPPrroocceedduurreess............................2299--3344
After Balance Vibration Problems . . . . . . . . . . . . .29
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .30 - 33
Machine Self-Test “Green Screen” . . . . . . . . . . . .34
MMaaiinntteennaanncceeIInnssttrruuccttiioonnss..............................3355
Monitor Screen Adjustment . . . . . . . . . . . . . . . . .35
IInnssttaallllaattiioonnIInnssttrruuccttiioonnss..........................3366--3377
Receiving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Electrical Requirements . . . . . . . . . . . . . . . . . . . . .36
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Air Supply Connection . . . . . . . . . . . . . . . . . . . . . .36
Connect to Power . . . . . . . . . . . . . . . . . . . . . . . . .36
Floor and Space Requirements . . . . . . . . . . . . . . .37
SSppeecciiffiiccaattiioonnss..................................................3388
FFeeaattuurreess........................
..................................3388
RReeqquuiirreeddAAcccceessssoorriieess....................................3399
OOppttiio
onnaallAAcccceessssoorriieess......................................3399
GGlloossssaarryyooffTTeerrmmss..........................
................4411
11775500//11880000FFuunnccttiioonnaallCChheecckkffoorr
CCaalliibbrraattiioonn.......................................
.BBaacckkCCoovveerr

2 • Important: Always read and follow the on-screen operating instructions.
Video Balancer
BBaallaanncciinnggYYoouurrFFiirrssttTTiirree
Important: Always read and follow the on-screen
operating instructions.
1. Turn the machine OFF then ON
(resets machine).
The initial screen is in dynamic mode using standard
clip-on wheel weight locations and wheel dimensions.
2. Mount a tire/wheel on the
balancer that will use standard clip-
on wheel weights.
Use the most appropriate mounting method.
3. Always remove any weights
already attached to the wheel.
Use the most appropriate mounting method. Always
remove any weights attached to the wheel.
4. Enter A & D wheel dimensions
using offset arm.
For Automatic Measurement — pull the offset arm
out to the wheel, hold it still at clip-on weight position
against the wheel flange, and wait for the BEEP.
Clip-on Weight Location — viewed on a cut-away rim
for clarification.
5. Enter Width wheel dimension.
Enter Width at DIM screen or, if equipped with the
Hood Sensor System, lower the hood to automatically
measure tire width.
6. The wheel spins and unbalances
are measured and displayed.
The corrective weight amount appears on the video
display screen for the left and the right planes of the
wheel, see figure 3.
7. Raise hood after tire stops
rotating.
Note: If the hood is raised before the end of the spin,
an error screen will appear. Wait for the weight
amounts to display before raising the hood.
8. Rotate wheel to position left side
placement arrow at the center bar.
As illustrated in figure 3, rotate the wheel to position
the left side placement arrow at the center red bar.
Step on the positioning pedal to hold the tire in place.
9. Attach left side corrective weight
amount at top-dead center on the
inside flange of the wheel.
Attach specified corrective weight amount (0.25 oz in
figure 3) at top-dead-center on inside flange of wheel.
10. Rotate wheel to position right
side placement arrow at center bar.
Rotate the wheel to position the right side placement
arrow at the center red bar. Step on the positioning
pedal to hold the tire in place.
11. Attach the right side corrective
weight.
Attach specified weight amount (0.75 oz in figure 3) at
top-dead-center on the outside flange of the wheel.
12. Lower the hood to respin the
tire/wheel and check balance.
Your weight readings should now be 0.00.
Note: Throughout this manual tire dimensions are
referred to as A, W, and D, see figure 2.
Figure 2 - A, W, and D Tire Dimensions
Figure 1 - Automatic Measurement
Metal Offset Arm Plastic Offset Arm

Note: To reset the mode back to the initial screen at
any time, press the DYNAMIC option or press the
key, or turn the machine OFF then ON. Note that
if an operator is in a balance mode, it may be neces-
sary to finish the balance cycle first.
MENU
2
Figure 3 - Weight Placement Screen Using Clip-on Weights
in Dynamic Mode
Important: Always read and follow the on-screen operating instructions. • 3
Video Balancer
Important: Always
read and follow the
on-screen operating
instructions.

4 • Important: Always read and follow the on-screen operating instructions.
PPrriinncciipplleeOOppeerraattiinnggPPaarrttss
Video Balancer
Monitor
Portable Sliding
Storage Tray
Sensor Target Bracket
(for calibration)
40 MM Shaft
Radial Runout
Sensor (adjustable
to center of tread)
Clip-on Air
Chuck for
Tire Inflation
Adjustment
Lateral Runout
Sensor (adjustable
to sidewall of tire)
ON/OFF and
Circuit Breaker
(back of machine)
115 V UL
Approved Plug
(back of machine)
Offset Arm with
Tape-A-Weight™
Feature,
Measures A&D
of Tire/Wheel
(shown in home
position)
Touch Panel

Important: Always read and follow the on-screen operating instructions. • 5
Video Balancer
Tool Accessory
Storage
Captured
Cone Spring
Printer
Protected Side
Storage Pegs for
Accessories
Positioning Pedal -
Holds Position for
Weight Application
Tilting Monitor
Adjustment Knobs
Adjustable
Air Gauge
Manual Tire
Bleed Valve
Inflate Button
Weight Tray with
Dual Pockets for
Weights thru 2 oz.
- Deep Pockets
thru 4 oz.
Tire Width Sensor
(measures when
hood is lowered)

6 • Important: Always read and follow the on-screen operating instructions.
Video Balancer
Power Switch
The ON/OFF decal, see figure 4, indicates the loca-
tion of the ON/OFF switch at the back of the balancer.
The circuit breaker reset button is also at this location.
Air Gauge Panel
NEVER exceed tire manufacturer’s recom-
mended air pressure. Tires can explode,
especially if inflated beyond these limits.
Keep hands, arms, and entire body back
from inflating tire. Avoid distraction during
inflation. Check tire pressure frequently to
avoid over inflation. Excessive pressure can
cause tires to explode, causing serious
injury or death to operator or bystander.
Do not lower the hood with the clip-on air
chuck attached to the tire’s valve stem.With
the hood start feature ON, the tire will start
rotation causing damage to the wheel and
balancer and possible personal injury.
As shown, the wheel balancer is equipped with the
capability to adjust the air pressure of the tire. The
INFLATE push button supplies air through the hose
and clip-on air chuck located at the wheel guard. When
the chuck is attached to the valve stem, air pressure is
indicated on the gauge. Excess pressure can be
reduced using the MANUAL TIRE BLEED VALVE. See
figure 4.
Figure 4 - Air Gauge Panel and ON/OFF switch decal that
indicates ON/OFF switch location at the back of
the balancer.
Positioning Pedal
Use the positioning pedal to hold the wheel position
during weight application, as shown in figure 5.
Do not actuate the positioning pedal during
the measurement cycle. Do not use the
positioning pedal as a brake.
Figure 5 - Positioning Pedal
CAUTION
CAUTION
WARNING
Air Gauge
Inflate
Button
Manual Tire
Bleed Valve
Press Positioning Pedal with
Foot to Hold Wheel Position

Important: Always read and follow the on-screen operating instructions. • 7
Video Balancer
Using the Offset Arm
When prompted by the on-screen instructions, use
the offset arm, see figure 6, to enter A & D measure-
ments automatically.
Figure 6 - Offset Arm
To measure for a clip-on weight location, place the
offset arm at the wheel flange as shown in figure 7A
(metal arm) or figure 7B (plastic arm).
Figure 7A - Clip-on Weight Location Using Metal Offset Arm
Viewed on a Cut-Away Rim for Clarification.
Figure 7B - Clip-on Weight Location Using Plastic Offset Arm
Viewed on a Cut-Away Rim for Clarification.
To measure for a hidden weight location, place the
offset arm at a hidden weight placement location as
shown in figure 8.
Figure 8 - Hidden Weight Location Viewed on a Cut-Away
Rim for Clarification.
Use the offset arm Tape-A-Weight™ feature for accu-
rate placement of hidden weights. See figure 9.
Figure 9 - Hidden Weight Placement Location Viewed on a
Cut-Away Rim for Clarification.
Note: Throughout this manual wheel weights are
referred to as Clip-on or Tape-A-Weight™ (Hidden
Weight). Figure 10 shows an example of each weight.
Figure 10 - Corrective Weight Examples. For Best Results,
use BADA®Brand Wheel Weights.
Wheel Flange
Wheel Flange
Hidden Weight
Placement Location
Location for
Hidden Weight
Clip-on Weight Tape-A-Weight™

8 • Important: Always read and follow the on-screen operating instructions.
Video Balancer
Sensor Measuring Systems
By lowering the hood, measure wheel width auto-
matically using the Tire Width Sensor. See figures 10
and 11.
Figure 10 - Tire Width Sensor
Figure 11 - Screen with Width Sensor Icon
The sensor, shown in figure 12, is mounted on an
adjustable slide at rear of machine and is used to
measure radial runout of the tire when the eye of the
sensor is centered on the tread width.
Important: To activate the radial runout function,
press the button, select the GENERAL SET-UP
option , and set the RUNOUT UNLOADED 
option to SONAR.
Figure 12 - Radial Runout Sensor
The sensor, on especially equipped models, (shown
in figure 13) is mounted on an adjustable slide and is
used to measure lateral runout of the tire when the eye
of the sensor is centered on the flat of the tire side-
wall.
Important: To activate the lateral runout function,
press the button, select the GENERAL SET-UP
option , and set the RUNOUT UNLOADED 
option to SONAR.
Figure 13 - Lateral Runout Sensor
6
5
MENU
7
5
MENU
Lateral Runout
Sensor
Tire Width Sensor

Important: Always read and follow the on-screen operating instructions. • 9
Printer
Use the printer, on especially equipped models,
(shown in figure 14) to provide a BALANCER CERTIFI-
CATE for the wheel balance service.
Figure 14 - Printer
Important: The soft-
ware will not recognize
the printer unless there
is paper in the printer.
This is also the case if
the paper is threaded
between the paper roller
and the printer top cover.
The flashing LED on front of printer indicates power
to the printer, but the printer could still be incorrectly
connected or out of paper.
Important: To activate the printer function, press the
button, select the GENERAL SET-UP option
select the PRINTER option , and set the PRINTER
option to ON.
Also, toggle ON or OFF the following printer options
for the printout (default is ON for all these options):
Option OWNER ADDRESS - prints the owner’s
address (see page 15 to customize to the machine).
Option SPIN NO. - records the spin no. from
CYCLE HISTORY (see page 16 for more information).
Option OPERATOR NO. - indicates the operator
number and name (see page 17 to customize to the
machine).
Option VEHICLE TAG NO. - provides a space for
the operator to write in the vehicle tag number.
Option LOC. ON VEHICLE - operator uses this
diagram to manually check the wheel location that was
serviced.
Option CORRECTED - operator uses this area to
manually check either YES if runout was corrected or
N.R. if not required.
On selected screens, to print the BALANCER CER-
TIFICATE press option . Note that the printout
option CORRECTED is only available for RUNOUT
DIAGNOSTIC (see MATCHING on page 20 for more
information).
Figure 15 - Completed Printer Balancer Certificate
7
6
7
6
5
4
3
2
1
5
5MENU
Video Balancer
Printer
Install Roll of
Thermal Paper

10 • Important: Always read and follow the on-screen operating instructions.
Video Balancer
UUnnddeerrssttaannddiinnggtthhee
VViiddeeooDDiissppllaayySSccrreeeennss
The video display screens provide access to func-
tions, options, and on-screen instructions for the oper-
ator. See figure 19 for the Monitor and Initial Screen
Feature Reference.
1. Access additional functions by pressing one of the
following four keys, at the bottom of the monitor.
-brings up a menu screen. Press MENU again
(toggle) to return to the previous screen.
-provides on-screen help instructions for the
current screen.
-begins a measurement cycle, if the hood is
lowered.
-stops a measurement cycle or exits a screen
as noted in instructions.
2. To select a screen option, press the numbered key
that corresponds with the key icon along the bottom of
each video display screen. See figure 16.
Figure 16 - Select an Option by Pressing Its Corresponding
Numbered Key
3. Always refer to the screen dialogue area for
important operating instructions.
4. Refer to the Mode Icon in the upper right hand
corner of the screen for mode and weight placement
type.
Mode Icon Examples:
5. An option with the symbolindicates the pres-
ence of additional screens. In the example below,
press key to view the next screen.
Menu Option Example:
6. At the weight placement screen align the weight
placement arrows for correct positioning of hidden
weights. See figures 17 and 18.
Figure 17 - Weight Placement Arrows in 3D Mode.
Figure 18 - Weight Placement Arrows in Profile Mode.
1
STOP
START
HELP
MENU

Important: Always read and follow the on-screen operating instructions. • 11
Video Balancer
On-screen
Instructions
Operator Display
Weight
Display
DIM
Icon
*
Mode
Icon
Static Unbalance Icon
(appears when over
1.1 oz is present)
Econo Balance
Mode Icon
* Profile Tire Image
RO Max.
(Instant Reading of
Wheel Runout)
* On selected
screens, can toggle
to a 3D tire image.
Numbered
Key
Key Icons
Monitor and Initial Screen Feature Reference
Option Key
Screen Option
Weight
Placement
Arrow
Centering Bar
Weight
Location
Icons
Figure 19 - Monitor and Initial Screen Feature Reference
Static-on-Screen™

12 • Important: Always read and follow the on-screen operating instructions.
Video Balancer
Runout
Runout Unloaded SONAR
Runout Unloaded SONAR
Runout diagnostic ON
Runout Limits 
4
3
2
1
See page 14
for additional
information.
Menu Screen Flowchart
Press the key for the Menu screen to access
balancer function screens and to set configuration
screens. See the flowchart below.
MENU
Cycle History
Spins between calibrations 1000
Daily Spins Nr.: 34
Spins since Calibration: 75
Total Spins Nr.: 81
1
General Set-up
Language English
Screensave time 0 min.
Clock setting 
Video sleep mode time 60 min.
Excessive static unbalance ON
Printer 
Runout 
7
6
5
4
3
2
1
Clock Setting
Month: 7
Day: 24
Year: 2004
Hour: 15
Minutes: 5
Day: THU
12/24 Hour Clock: 24
7
6
5
4
3
2
1
Balancing Set-up
Display Units oz
Lower Weight Limit 0.25 oz
Calculation Roundoff 0.25
Start by Lowering Hood ON
Sound Signal ON
Econo Bal Lower Wt Limit 0.64 oz
7
6
5
4
3
2
1
Menu
Optimization (Match Balance) 
Runout (Runout Match) 
Cycle History 
Service Adjustments 
General Set-up 
Balancing Set-up 
Special Functions 
7
6
5
4
3
2
1
1
3
4
5
6
7
See 15 for
additional infor-
mation.
See page 14
for additional
information.
See page 16
for additional
information.
2
PASSWORD
PASSWORD
PASSWORD

Important: Always read and follow the on-screen operating instructions. • 13
Video Balancer
Service Adjustments
Distance Arm Calibration 
Width Sonar Calibration 
Diameter Arm Calibration 
Distance/Diameter Arm Type Metal
Temperature 70º F
7
5
3
2
1
Distance Arm Calibration
On-screen Instructions
Width Sonar Calibration
On-screen Instructions
Optimization
(Match Balance)
On-screen Instructions
Alphabet Entry
On-screen Instructions
Alphabet Entry
On-screen Instructions
Self-Test Screen
Diameter Arm Calibration
On-screen Instructions
Machine Self-Calibration
On-screen Instructions
Special Functions
Owner Address 
Operators Name 
Machine Self-Test 
Static Unbalance Displayed ON
Stop On Top OFF
Machine Self-calibration 
6
5
4
3
2
1
See page 27
for additional
information.
See page 21
for additional
information.
See page 15
for additional
information.
Printer
Printer ON
Owner Address ON
Spin No. ON
Operator No. ON
Vehicle Tag No. ON
Loc. on Vehicle ON
Corrected ON
7
6
5
4
3
2
1
See page 14
for additional
information.
Graph Screen
On-screen Instructions
See page 22
for additional
information.
Runout Limits
Max. True Runout Limit 0.050"
Rim Runout Limit 0.010"
Correction Runout Limit 0.030"
3
2
1
PASSWORD

BBaallaanncceerrFFuunnccttiioonnSSeett--
uuppaannddRReevviieeww
See the Menu Screen Flowchart on page 12 and 13 for
screen access information.
Indicates recommended settings.
General Set-up
Press the key and select the GENERAL SET-UP
option for the following menu selections.
Figure 20 -  General Set-up Screen
Language - Toggle to display English, Español, or
Français.
Set to ENGLISH.
Screensave time - Set from 1 to 10 minutes @ 1
minute increments.
Clock setting - Set the month, day, year, hour,
minutes, day, and 12/24 hour clock.
Figure 21 - Clock Setting Screen
Video sleep mode time - Set the range from 0
through 60 minutes.
Set to 60 min.
Excessive Static Unbalance -Toggle ON or OFF to
detect whether the static unbalance limit is
exceeded.
Set to ON.
Printer - Toggle ON or OFF to set the printer,
owner address, spin no., operator no., vehicle tag
no., loc. on vehicle, and corrected options.
See PRINTER on page 9 for further details.
Figure 22 - Printer Screen
Runout - Set runout options from this menu.
Figure 23A - Runout Screen
Runout Unloaded -(lateral) toggle to
OFF or SONAR.
Set to OFF for the XR
1800 Model! Set to ON for the XR
1850 Model!
Runout Unloaded -(radial) toggle to
set to OFF or SONAR.
Set to SONAR.
Runout Diagnostic - Toggle ON or OFF.
See MATCHING pg. 20 for further details.
Runout Limits - Tolerances that indicate
the limit of runout allowed on the
tire/wheel. Set tolerances within the fol-
lowing range:
Note: See MATCHING on page 20 for further details.
4
3
2
1
7
6
5
4
3
2
1
5
MENU
14 • Important: Always read and follow the on-screen operating instructions.
Video Balancer
 Shown with Recommended Settings
 Shown with Recommended Settings