Herman Miller Caper Installation instructions

Z
© 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Caper are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b9rtf rev A.
1
Table of Content
1. Multipurpose Chair Disassembly .......................................................................2
2. Footring Disassembly........................................................................................8
3. Stacking Chair Disassembly............................................................................10
4. Tablet Arm Disassembly..................................................................................12
5. 4 Leg Stool Disassembly.................................................................................13
YCaper®Disassembly for Recycling Instructions

Z
© 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Caper are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b9rtf rev A.
2
YCaper®Disassembly for Recycling Instructions
Multipurpose Chair Disassembly
Power driver Safety Glasses Socket Rubber
Mallet
T-40 Torx
Driver
Flat Screw Driver Hammer Nose Plier
Multipurpose Chair Disassembly:
Tool Required:
1. Invert chair on padded
corner of table top.
Materials Identication and Segregation:
Where possible, plastic components are marked with ASTM recycling codes. Use these codes to
identify material type for recycling. Non marked components should be treated as mixed plastic.
Ferrous metals can be identied using a small magnet for recycling. Non-ferrous metals should be
separated and recycled separately.
2. Hold base and pull hard
to remove caster from base.

Z
© 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Caper are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b9rtf rev A.
3
4. Lift the base from
pneumatic cylinder and pull
off.
5. Remove cylinder from tilt
by hitting bottom of tilt with
mallet.
3. Using a 7/8” dia socket, or
something equivalent, strike
socket to dislodge the base
from the cylinder.
6. Pull out the cylinder from
assembly.

Z
© 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Caper are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b9rtf rev A.
4
7. Using T-20 torx
screwdriver, remove and
properly dispose of set
screws from yoke.
8. Pull arm out of back
frame post.
9. Pull back off frame posts. 10. Remove the back properly.

Z
© 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Caper are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b9rtf rev A.
5
11. Using T-40 torx ratchet
wrench service tool, remove
fasteners from carriage.
13. Cut the pellicle off and
remove foam.
12. Remove the seat
assembly from tilt.
14. Using head screw driver
remove the screws from seat
pan.

Z
© 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Caper are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b9rtf rev A.
6
16. Using T-20 torx head
driver remove torx head
screws from gear retainer.
15. Pull guide bearing from
carriage on seat.
17. Remove gear retainer
and lift knob from tilt
assembly.
18. Remove spring and
drivescrew from tilt
assembly.

Z
© 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Caper are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b9rtf rev A.
7
20. Remove yoke from tilt.
19. Using T-40 torx ratchet
wrench tool, remove fasteners
and bearing securing yoke to
carriage and dispose of
properly.

Z
© 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Caper are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b9rtf rev A.
8
Footring Disassembly:
1. Invert chair on padded
corner of table top. 2. Hold base and pull hard
to remove caster from base.
4. Lift the base from
pneumatic cylinder and pull
off.
3. Using a 7/8” dia socket, or
something equivalent, strike
socket to dislodge the base
from the cylinder.
YCaper®Disassembly for Recycling Instructions
Footring Disassembly

Z
© 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Caper are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b9rtf rev A.
9
5. Lift the footring from
pneumatic cylinder and pull
off.

Z
© 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Caper are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b9rtf rev A.
10
2. View arm of chair from
underside of back. Using
small straight head screw-
driver, depress sping pin
from end of arm.
1. Removing caster or
glides.
Stacking Chair Disassembly:
3. Pull arm out of back
frame post. Repeat the
steps 2 and 3 for other side.
4. Pull back off frame posts.
YCaper®Disassembly for Recycling Instructions
Stacking Chair Disassembly

Z
© 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Caper are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b9rtf rev A.
11
8. Remove the seat.
6. Using 1/8” punch and
hammer, drive post fastener
from push on fastener in
bumper. Repeat procedure
for other post fasteners.
7. Remove bumpers from
bottom of frame.
5. Remove the back properly.

Z
© 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Caper are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b9rtf rev A.
12
3. Takeout the Tablet Arm and Cover.
1. Lay the Chair on side.
Tablet Arm Disassembly:
YCaper®Disassembly for Recycling Instructions
Tablet Arm Disassembly
2. Remove cover to tablet
with 7 pan head screws.

Z
© 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Caper are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b9rtf rev A.
13
4 Leg Stool Disassembly:
2. View arm of chair from
underside of back. Using
small straight head screw-
driver, depress sping pin
from end of arm.
1. Removing caster or
glides.
3. Pull arm out of back
frame post. Repeat the
steps 2 and 3 for other side.
4. Pull back off frame posts.
YCaper®Disassembly for Recycling Instructions
4 Leg Stool Disassembly

Z
© 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Caper are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b9rtf rev A.
14
8. Remove the seat.
6. Using 1/8” punch and
hammer, drive post fastener
from push on fastener in
bumper. Repeat procedure
for other post fasteners.
7. Remove bumpers from
bottom of frame.
5. Remove the back properly.