Herman Miller Setu Lounge Chair Installation instructions

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b5vn8 rev B.
1
YSetu®Disassembly for Recycling
Tools Required:
Power Driver Small Flathead
Screwdriver Safety GlassesT-27 Torx Bit (2.75” or longer)
2 lbs Hammer
Utility Knife Rubber Mallet
T-20 Torx Driver
Materials Identication and Segregation:
Disassembly Steps:
Where possible, plastic components are marked with ASTM recycling codes. Use
these codes to identify material type for recycling. Non marked components should
be treated as mixed plastic. Ferrous metals can be identied using a small magnet for
recycling. Non-ferrous metals should be separated and recycled separately.
2.1 Grasp and pull to remove
Casters from the Base.
1.1 Lay chair on back.
Caster

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b5vn8 rev B.
2
5.1 Use small Flathead
Screwdriver to disengage
black plastic connector of
Height Adjustment Cable
from top of Cylinder.
6.1 Use small Flathead
Screwdriver to disengage
ball of Height Adjustment
Cable from top of Cylinder.
3.1 Hold Base legs rmly and
strike the bottom of cylinder
with rubber mallet until Base
comes loose.
Caution: Do not strike cylinder
directly with metal hammer, use
rubber mallet only!
Height Adjustment
Cable
Screwdriver
Rubber Mallet
4.1 Remove Base.

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b5vn8 rev B.
3
9.1 Use a T-20 Torx Driver to
remove screws. 10.1 Remove Height Adjustment Assembly.
7.1 Place one hand on can of
Cylinder and hit the bottom of
the chair with hammer until
Cylinder seperates from chair.
8.1 Remove Cylinder.
Hit hammer here
T-20 Torx
Driver

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b5vn8 rev B.
4
12.2 Remove Shoulder Bolts.
12.1 Using a Power Driver with a
T-27 bit, remove Shoulder Bolts.
11.1 Using a Utility Knife cut
Seat Fabric in half.
Power Driver

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b5vn8 rev B.
5
13.1 Using a Power Driver
with a T-27 bit, remove Bolts.
14.1 Remove Arms. 15.1 Remove Inner Bushing.

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b5vn8 rev B.
6
18.1 Remove T-Nut from No
Arm Plug.
16.1 Remove T-Nut from Arm. 17.1 Remove No Arm Plug
from opening in Beam.

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b5vn8 rev B.
7
20.1 Remove Inner Bushings.
19.1 Using a Power Driver with a
T-27 bit, remove Shoulder Bolts.

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b5vn8 rev B.
8
23.1 Using a Powerdrill with a
T-27 bit, remove Shoulder Bolts. 24.1 Remove Rear Links.
21.1 Using a Powerdrill with
a T-27 bit, remove Screws. 22.1 Remove TiltAssembly from Seat Assembly.

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b5vn8 rev B.
9
28.1 Using a small shaft or
screwdriver. Remove pressed
T-Nut from both Links.
27.1 Remove Front link.
25.1 Remove Shoulder Bolts
using Power Driver. 26.1 Remove 4 Inner Bushings.

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b5vn8 rev B.
10
30.1 Remove T-Nuts from
Seat frame.
29.1 Pull Fabric out of groove in
Seat frames to remove. Remove
metal clips from fabric.
T-Nut Location