Herman Miller Prospect Media Space Installation instructions

Parts Included
Tools Required
HermanMiller
Prospect™Media Space Installation and
Disassembly for Recycling Instructions
How to assemble your Prospect Media
Space.
Power Driver
Foot Assembly
Toe Rail
LH Ledge
RH Ledge
Side Panel
RH End Rail
Mid Rail
LH End Rail
LH Toe Rail end Cap
Bottom Panel Clip
Top Panel Clip
RH Toe Rail End Cap
Glide
Step 1 Step 2
Phillips Bit Allen Wrench Level
Safety Glass
. Assemble Glides Fully into Foot Assemblies.
Toe Rail Mounting
Bracket
RH Toe Rail Endcap
LH Toe Rail Endcap
Long Side
Long Side
M x  Flathead
Hex Socket Screws
Hex Socket Button
Head Screws
Hex Socket Button
Head Screws
Glide
Foot Assembly
. Assemble Toe Rail Mounting Brackets to inner Foot Assemblies with M x
 Flathead Hex Socket Screws.
. Attach Toe Rail Endcaps to outer Foot Assemblies with Hex Socket Button
Head Screws. Note: Endcaps are Right and Le Handed.
Wire Trough
Peninsula Surface Connector Plate
Toe Rail Mounting
Bracket
M8 x  Flat Head
Socket Screw M8 x  Flat Head
Socket Screw
M8 x  Flat Head
Socket Screw
M x  Flathead
Socket Screw
Hex Socket Button
Head Screw
Hex Socket Button
Head Screw
Phillips Button
Head WoodScrew
M x  Hex Socket
Head Cap Screw
Spider
Foot Column
Bag Hook
Table Clamp Cup
HermanMiller Assembly Instructions1BJZTY rev B

HermanMiller Assembly Instructions2BJZTY rev B
Step 3 Step 4
Step 6
Step 5
. Align Bag Hook Brackets as square as possible to feet. Attach Bag Hook
Brackets with M x  Flathead Hex Socket Screw on each foot assembly.
. Position Connector Plates onto Peninsula surface.
. Secure plates to surface with M x  flathead socket screws.
. Arrange inverted Foot assemblies in proper positions.
. Assemble Toe Rails to mounting brackets and endcaps on foot assemblies
with M x  Hex Socket Flathead Screws. Tighten screws aer all have been
started. Make sure all Toe Rails are pushed tight together, with no gaps,
before tightening.
Bag Hook
Bag Hook
Toe Rail
Toe Rail
Toe Rail
Bag Hook
M x  Flathead
Hex Socket Screw
M x  Flathead
Hex Socket Screw
M x  Flathead
Hex Socket Screw
M x  Flathead
Hex Socket Screw
M x  Flathead
Hex Socket Screw
M x  Flathead
Hex Socket Screw
M x  Flathead
Hex Socket Screw
M x  Flathead
Hex Socket Screw
Inner Foot RH End Foot LH End Foot
Wire Trough
Connector Plate
M x  Flathead
Socket Screw
. Set Worksurface upside down on clean padded surface.
. Position Wire Trough onto Peninsula Surface.
. Secure Wire Trough to Peninsula Surface with Phillips Button Head Wood
Screws. Be cautious not to strip out holes.
No Gap

HermanMiller Assembly Instructions3BJZTY rev B
Step 9
Step 8
Step 7
. Spin Glides into feet.
. Set Peninsula Assembly onto Cove Leg Assembly. Top of Bag Hooks t
into pockets in Peninsula Surface.
. Secure surface to legs with M x  flathead socket screws.
. Secure Spider to Column with hex socket button head screw.
. Position Foot onto column.
. Capture foot inside of column with Table Clamp.
. Secure clamp with M x  Flathead socket screw.
. Repeat process for other  feet.
. Attach Peninsula Leg Assembly to surface assembly with M x  hex
socket head cap screws.
M x  Flathead
Hex Socket Screws
Hex Socket Button
Head Screws
Foot
Table Clamp
Peninsula Assembly
Cove Leg Assembly
Spider
Glide
Glide
Glide
Glide
Column
Peninsula Leg
Assembly
M x  Hex Socket
Head Cap Screw
M x  Flathead
Socket Screw

HermanMiller Assembly Instructions4BJZTY rev B
Step 10
. Position LH and RH Ledges onto assembly.
. Secure ledges to assembly with M x  flathead socket screws.
RH Ledge
LH Ledge
M x  Flathead
Socket Screw
M x  Flathead
Socket Screw
M x  Flathead
Socket Screw
Slot
Dovetail
Groove
Step 11
. Slide Rails onto dovetail on back of legs. Slots on side of rails should
always be at bottom. There are right and le hand end rails. Grooves must
face inward toward toe rail.
Inside Rail
Inside Rail
RH End Rail
LH End Rail
Side Panel
Step 12
. Peel protective lm from side panels. Long sweeping pull helps remove
faster. Be sure to hold panel rmly, pushing down into carpet while a partner
pulls.
. Assemble Bottom Panel Clips to inside surface of each panel at bottom
corners.
. Assemble Top Panel Clips to inside surface of panels at top corners.
Bottom Panel Clips Bottom Panel Clips
Top Panel Clips
Top Panel Clips

HermanMiller Assembly Instructions5BJZTY rev B
. Insert bottom panel clips into slots. Pull down on panel until bottom
panel clips are positioned into slots in bottom of rails.
Step 13
Step 14
. Insert bottom panel clips into slots. Pull down on panel until bottom
panel clips are positioned into slots in bottom of rails. May need to push in
on panel from outside to keep clips fully engaged inside of grooves.
. Turn glides as needed to make wall assembly level.
. Turn glides on peninsula leg to make peninsula surface level.
Grooves
Side Panel
Glide
Glide Glide
Glide
Glide
Side Panel
Side Panel
Slot
Rail
Bottom
Panel
Clip
Step 15
. Insert flange on Cup into groove in rail. Turn Cup downward to lock in
place.
Rail
Flange Cup
Groove

HermanMiller Assembly Instructions6BJZTY rev B
Disassembly and Recycling:
Materials Identication and Segregation:
Where possible, plastic components are marked with ASTM recycling
codes. Use these codes to identify material type for recycling. Non marked
components should be treated as mixed plastic. Ferrous metals can be
identied using a small magnet for recycling. Non-ferrous metals should be
separated and recycled separately.
To disassemble product, reverse the above installation steps.