Herman Miller Vivo Installation instructions

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Action Office, Abak and Vivo are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu, Traverse and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
1b5ydk Rev H.
1
YVivo® Interiors Frameless Glass Screen Installation
and Disassembly for Recycling Instructions
Parts Included:
For Standard Trim
Tools Required:
Screen Glass
Torque Wrench
Clamp Filler Clamp Plate
Hex Head Screw Hex Nut
Clamp
A
B
EF
CD
Top Cap Clip
H
Top Cap
GShim Spanner
(Between 2
Top Caps)
JK
Ratchet Wrench 1/2 Hex Socket Safety Glasses

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Action Office, Abak and Vivo are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu, Traverse and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
1b5ydk Rev H.
2
Screen Glass
A
Top Cap (2)
G
Clamp
Landscape
Support Finished End Clip
B
HL
Clamp Filler
CClamp Plate
D
Hex Head Screw
Spanner Clip
E
K
Hex Nut
F
Shim (2 or 4)J
Ratchet Wrench Torque Wrench 1/2” Hex Socket Safety Glasses
Parts Included:
Tools Required:
For Architectural Trim

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Action Office, Abak and Vivo are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu, Traverse and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
1b5ydk Rev H.
3
B
C
E
2. Place Clamp assemblies into cutouts in top
rail of Frame.
3. Position Clamp Plates (D) into Cutouts in
underside of frame top rail.
4. Install Hex Nut (F). Do not tighten.
Clamp Assembly
Cutout
Clamp Assembly
Cutout
D
F
D
F
1. Insert Hex Head Screws (E) into
underside of Clamps.
Clamp Assembly Instructions:
Glass Assembly Instructions:
1. Firmly push Glass into Clamps.
Note: Wire channels and landscape support (H)
should be installed prior to glass.
Wire
Channel
Wire Channel
A2. Center Glass on Frame or
between Frames.
3. Center Clamps on rail front to
back and tighten Clamps.
Torque Nuts on Clamp Assemblies
to 75 in/lbs.
Note : To align glass in panel run
insert supplied Shim (J) between
Clamp and Frame. Shim can be
folded to increase thickness.
J

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Action Office, Abak and Vivo are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu, Traverse and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
1b5ydk Rev H.
4
H
G
HOrientation of clip when
snapped in place
Orientation of clip
when sliding
Tile
1a. Slide Top Cap Clips at an angle (H) onto Top Caps (G). One on each end, 3” to 4”
from end of Top Cap. The other Clip in the middle of Top Cap.
1b. Push down into place to engage clip.
2. Install Tiles onto Frames.
For Standard Trim Only
3” - 4”

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Action Office, Abak and Vivo are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu, Traverse and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
1b5ydk Rev H.
5
Standard Trim Application Frame to Frame
3. Add spanner clip (K) between glass panels.
4. Slide top cap onto and past spanner clip.
5. Slide top cap in opposite direction.
6. Engage top cap with connector cover cap or finished end.
Repeat step 3-6 from one end of run to the opposite end of run.
7. Press top caps firmly onto hook rails.
KG

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Action Office, Abak and Vivo are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu, Traverse and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
1b5ydk Rev H.
6
For Architectural Trim Only
Landscape Architectural to Cap Support Assembly
1. Align pins on support with holes in wire channel.
2. Install Glass - (Refer to Glass Assembly Instructions)
3. Install Cladding onto Frame.
H
Cladding
H

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Action Office, Abak and Vivo are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu, Traverse and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
1b5ydk Rev H.
7
Spanning 2 Architectural Top Caps - Spanner Clip (K)
Architectural Finished End Clip Assembly (L)
3. Lower center clip between wire channels
4. Slide top caps over spanner clip and into position.
5. Slide finished end clip into top caps.
6. Start clips on finished end into frame. Push down on finished end
while pulling out on top. Pins on finished end will engage with top caps.
K
L
Finished
end

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Action Office, Abak and Vivo are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu, Traverse and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
1b5ydk Rev H.
8
Disassembly for Recycling:
Materials Identification and Segregation:
Where possible, plastic components are marked with ASTM recycling codes. Use these
codes to identify material type for recycling. Non marked components should be treated
as mixed plastic. Ferrous metals can be identified using a small magnet for recycling.
Non-ferrous metals should be separated and recycled separately.
To disassemble product, reverse the above installation steps.