Herman Miller Locale T-Desk User manual

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
1
LOCALE HEIGHT ADJUSTABLE DESK OPERATING INSTRUCTIONS
CAUTION: WHEN OPERATING THIS DESK,
MAKE SURE TO REMOVE ANY OBJECTS OR
OBSTRUCTIONS THAT COULD BE IN THE WAY OF
THE MOVING DESK TOP. The rated load For the desk
is 200 lbs. maximum.
1) To operate the height adjustable desk, press the up or
down arrows on the control switch located under the
front edge of the desk top.
2) Press the up arrow to move the desk top higher.
3) Press the down arrow to move the desk top lower.
PARAMÈTRES RÉGIONAUX RÉGLABLE EN HAUTEUR BUREAU
INSTRUCTION DE FONCTIONNEMENT
ATTENTION : LORS DE L’UTILISATION DE CE BUREAU, ASSUREZ-VOUS DE RETIRER
TOUT OBJESCTS OU OBSTRUCTIONS QUI POURRAIENT ÊTRE DANS LA FACON DE LE
DEPLACER DESSUS DE BUREAU. LA CHARGE NOMINAL POUR LE BUREAU EST DE
90.7 KG MAXIMUM.
1) Pour faire fonctionner la hauteur réglable de bureau, appuyez sur les èches
vers le haut ou le bassur le commutateur de commande situé sous le bord du
bureau.
2) Appuyez sur la èche vers le haut pour déplacer le desk top supérieur.
3) Appuyez sur la èche vers le bas pour déplacer le bureau inférieur le plus
haut.
Control Switch
YLocaleTM L-Desk and T-Desk Installation

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
2
L-Desk
T-Desk
(Shown throughout instructions)

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
3
Parts Included:
Base Assembly Upper Case
M8 x 16 Hex Socket
Head Machine
Screw (4)
M8 x 30 Socket Flat Head
Machine Screw(12)
Work Surface
Support
Column
End Column
Rail
AB
M
L
D
J
K
M6 x 20 Socket
Flange Head Screw(8)
F
Base Top
C
Column Shroud
GWire Guide
H
E
Control Switch
N

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
4
Work Surface
V
Control Box
W
M5 x 12 Socket Button
Head Cap Screw(4)
M5 x 16 Socket Button
Head Flange Screw(6)
M5 x 12 Socket Button
Flange Head Machine
Screw(22)
X
AJ
Z
Mushroom Fastener(6)
Y
Service Chain
U
Cable Tray
Wire Tray
AA
AB
Shelf Pins(8)
AD
Shelf(2)
AC
Cable Clamp
Motor Cable Power Cable T
P R
Grommet Clamp(2)
AE M3.5 x 12 Plastite
Pozi Pan Head
Screw
AF Clamping Screw
AG

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
5
1. Place Base at desired location.
2. Open or remove Doors.
3. Remove Access Panels by pulling out at top of panel, then lifting up and out.
Access Panel
Access Panel
Door
Door
A
Tools Needed:
Power Driver #2 Phillips Bit Level
Dowel Pin
Column Leg Leg Glide
AH
AL AM
AN
M5 x 10 Flange Head
Screw(3)
AK
3mm Metric
Hex Bit 4mm Metric Hex Bit 5mm Metric
Hex Bit 6mm Metric Hex Bit
M8 x 25 Hex Socket
Head Machine
Screw (4)

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
6
6. If More than one unit are to be
installeded in a run; position adjoining
unit next to one already in position.
7. Level and align that unit to mate with
other.
8. Connect bases with 4 Clamping
Screws (C) and 1 Dowel Pin (D).
(Note: View shown with top panel
removed for clarity.)
C
D
4. Remove Bottom Shelves from Base.
5. Level base by adjusting Outside Glides rst. Then adjust Inside Glides down
to touch oor.
Outside Glide
Inside Glide
Bottom Shelf

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
7
Break Out
11. Break out opening in Access Covers if required.
12. Return Access covers to Base.
9. Remove Access Covers from Base End Panels.
10. Install Electrical Harnesses to Base.
Access Cover

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
8
C
J J J
AL AL AL
B
F
AN AN AN
AM AM AM
13. Position Base Top (C) or Upper Case(B) onto Base. Secure to Base with 8
Pan Head Machine Screws (F).
14. Turn Glides (AM) into Column Leg (AL).
15. Attach Column Leg to End Column (J) with 4 Hex Socket Head Machine
Screws (AN) with the torque 130 inch lbs or 15 Nm force.
T-Desk L-Desk, RH L-Desk, LH

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
9
E
D
16. Assemble Column(s) (D) to Base with 4 Socket Head Machine Screws (E).
17. Fully Tighten Top Screws. Loosely tighten Bottom Screws.
18. Move lower end end of column until Level on top casting shows true.
19. Fully tighten Bottom Screws.
Y
Y
AJ AJ
20. Determine which side of Work Surface Wire Cover will be accessed from.
Attach Mushroom Fastener (Y) to Column and End Column with Flange
Screws (AJ) where cover will latch. Image shows correct position for T-Desk.
Level
Top Screws
Bottom
Screws

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
10
21. Place End Column (J) bottom side up.
22. Set Rails (K) onto Column (J).
23. Position Work Surface Support (L) onto Rail.
24. Secure all together with 6 Flat Head Machine Screws (M).
25. Place the assembly onto the Column.
26. Position the other Work Surface Support (K) onto Rail.
27. Secure all in place with 6 Flat Head Machine Screws (L).
M
M
M
K
J
L
L
K

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
11
29. Adjust Positioning of Outboard Leg on L-desk by measuring from edge of
workbase to front glide of column.
30. Adjust Positioning of Outboard Leg on T-desk by measuring from edge of
workbase to front glide of column.
28. Level outboard round column by placing level on top of casting.
68.5” (1739mm)
56” (1425mm)

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
12
32. Connect lift wiring to Control Box (W).
33. Run cycle test on column. Raise column to full height.
W
N
31. For connecting to building power,
refer to BRE01. and BRE02.
installation instructions.

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
13
34. Position Shroud (G) around top of Column. Press down onto Base Top.
35. Secure Shroud in place with 2 Shroud Clamps (AE) and Pan Head Screw (AF).
36. Insert Wire Guide (H) into Column.
Press down to snap into Shroud and
steel bracket.
G
H
AE
AE
AF
AF
37. Lay chain on the oor with the open side of both end links point up. Then use a
Straight / Flat blade screwdriver to open each clasp.

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
14
38. Fully raise the column before installing chain and cords. Feed your cords from the
front all the way through the column and out the back side.
39. Place your cords into the chain, either end of the chain can be the top side. Then
close all but the top 3 or 4 links open for ease of attaching brackets later.

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
15
40. Feed energy chain through the grommet which is even with the work base top and
then through the top of the plate on the leg column making sure the snap open side
is facing towards the desk side of the leg. (Make sure the plastic grommet is installed
before you feed the chain through)
41. Attach top bracket.

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
16
42. After the chain is through the grommet and inside the work base install the
bottom bracket to the chain.

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
17
43. Install the bottom bracket to the upper inner framework hardware that attaches
the leg to the upper part of the work base. The bolt goes through bracket, then the
triangular opening of the leg attachment bracket, with the washer and nut on the
other side. (For a clearer view pictures do not show the chain)
BOLT
BRACKET
LEG BRACKET
WASHER
NUT

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
18
44. At the top of the leg feed the cords into the trough area and close the top clasps
that remained open on both ends of the chain.
45. Push the chain as far forward as possible while keeping the top bracket ush on
the top plate.

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
19
46. Screw bracket down to the top plate using the self-drilling screws. (NOTE: On L and
T desks, only one side of the bracket will screw onto the top plate)

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
TM Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bch5g rev D.
20
47. Wrap Control Switch Cable underneath z rails so it is trapped in gap between
two castings.
48. Press Control Switch cable rmly into cable retaining guides in Work Surface
Supports. Make loop in cable to take up slack in cable.
CARE Point - cable needs to be taught to aid retention.
49. Gather all cabling
and capture with Cable
Clamp (T).
50. Install Flange
Screw (AK).
T
AK
Pulled Taught
Cable Loop