Herman Miller Tu Installation instructions

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, TU are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 1
Part no. 1b9thv rev A.
YTu®Disassembly for Recycling
Tools Required:
Safety Glasses Ratchet Wrench Sledge Hammer
Flat Screw Driver
Steps:
2. Disengage slide and remove.
3. Repeat step 2 to remove
rest of slides.
1. Pull drawer out. Remove
from drawer slides.
Where possible, plastic components are marked with ASTM recycling codes. Use
these codes to identify material type for recycling. Non marked components should
be treated as mixed plastic. Ferrous metals can be identied using a small magnet
for recycling. Non-ferrous metals should be separated and recycled separately.
Materials Identication and Segregation:

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, TU are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 2
Part no. 1b9thv rev A.
5. Remove shelf from assembly.
6. Using phillips head screw
driver remove screws from
Spreader.
7. Remove top surface from
assembly.
4. Using phillips head screw
driver remove all screws
from shelf.

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, TU are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 3
Part no. 1b9thv rev A.
8. Using phillips head screw
driver remove screws from
inner panel.
9. Slide down and remove
inner panel from assembly.
10. Repeat step 8 and 9
to remove other side inner
panel.
11. Remove leveler.
12. Repeat step 11 to remove
other 3 levelers.
13. Using phillips head screw
driver remove screws from lock
assembly.

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, TU are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 4
Part no. 1b9thv rev A.
14. Remove lock from
assembly.
15. Using phillips head screw
driver remove screws from
end panel.
16. Remove drawer front. 17. Using phillips head
screw driver remove screws
from drawer front.

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, TU are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 5
Part no. 1b9thv rev A.
18. Remove handle from
drawer front.
20. Using Sledge hammer
hit on the concrete counter
weights and break into
pieces.
21. Remove Steel counter
weights from assembly.
19. Pull caster from base
and remove.