Herman Miller Vista Installation instructions

Tools Required
Parts Included (DVGT)
HermanMiller
Vista™ Rectangular Table with T-Foot
Leg Kit Installation and Disassembly for
Recycling Instructions
How to assemble Rectangular Table
with T-Foot Leg Kit
Worksurface
(Purchased Separately)
Stiener Socket Screw
Counter Weight
Pan Head
Rolling Screw (4)
Tapping Screw Cable Holder Power Cord
Switch M10 Screw
Rectangle
Control Box
Top Mounting
Plate
T-Foot Leg
Power Driver Phillips Bit Torque Wrench Metric Hex bit Square Drive Bit Torx Drive Bit
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical furnishing, basic precautions should always be followed,
including the following:
Read all instructions before using this furnishing.
DANGER - To reduce the risk of electric shock always unplug this furnishing from
the electrical outlet before cleaning.
WARNING - To reduce the risk of burns, re, electric shock, or injury to persons:
Close supervision is necessary when this furnishing is used by, or near children,
invalids, or disabled persons.
Sitting or standing on product may cause risk of personal injury (use for chairs,
tables consider obvious misuse of product).
Use this furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
Never operate this furnishing if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped into water. Return the
furnishing to a service center for examination and repair.
Failure to fully tighten screws (bolts) may cause injury by causing Vista tables to
collapse. Tighten screws (bolts) until they stop plus a quarter turn.
Periodically check to make sure legs are properly aligned. Failure to do so may
cause risk of personal injury.
If using power drive set on low torque.
Keep the cord away from heated surfaces.
Never drop or insert any object into any opening.
Do not use outdoors.
Do not operate where aerosol (spray) products are being used or where
oxygen is being administered.
This furnishing is intended for commercial use
control box rating: .A, V
Duty cycle:  min on,  min o
1HermanMiller Installation Instructions1BN5FF rev A

2HermanMiller Installation Instructions1BN5FF rev A
WARNING - Risk of Electric Shock – Connect this furnishing to a properly
grounded outlet only. See Grounding Instructions.
For loading always put heavier items in the center and distribute the load.
Risk of Injury - Maximum Load  lbs ( kg).
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This product is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
DANGER – Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. Check with a qualied electrician
or serviceman if you are in doubt as to whether the product is properly
grounded. Do not modify the plug provided with the product. If it will not t
the outlet, have a proper outlet installed by a qualied electrician.
This product is for use on a nominal -volt circuit and has a grounding
plug that looks like the plug illustrated in Sketch A. Make sure that the
product is connected to an outlet having the same conguration as the plug.
No adapter should be used with this product.
GROUNDED
OUTLET
GROUNDED
PIN
(A)
Step 
Top Mounting Plate Installation
. Pick the side on the leg where the power cable runs, face the cable
towards the center of the table.
. Ensure the cable is routed in the cutout.
. Install the Stamping Plate to the leg using  socket screws.
. Torque Screws to  -lbs.
. Do the same for other leg.
Step 
Leg Installation
. Lay the Surface upside down.
. Using the  predrilled holes to locate, install the leg using
 tapping screws.
. Do the same for other leg.
Note: Outbound Leg location shown. Inbound leg location will be
approximately  /” in from the edge of the table. For the condition
where one leg is inbound, one leg is outbound, pre-drilled holes will
locate the inbound leg. The outbound leg will be centered on the
surface front to back and /” in from the edge of the surface to the
edge of the top plate.
Step 
T Foot Installation
. Install the T Foot to the leg using  cap screws.
. Torque Screws to  -lbs.
. Do the same for other leg.
. For ” Table Feet, install counter weight to bottom of foot with
two thread forming screws then install the two M screws. Torque
the M screws to  -lb
/”
Forming Screws
M Screws
WARNING
The counterweight must be installed on 24" deep height adjustable tables. Failure
to do so can result in a reduction of table stability.

3HermanMiller Installation Instructions1BN5FF rev A
Step 
Stiener Installation
. Find the predrilled holes located near legs.
. Attach the Stiener to the rear side of worksurface using
Tapping Screws.
. Install Tapping Screws in every other hole. Alternate back and forth
on each flange.
Note: If worksurface other than Herman Miller’s is being installed.
Center legs front to back.
Distance between legs to be determined by length of stiener.
Step 
Control Box Installation
. Find the predrilled holes which are le of center at the rear
worksurface.
. Install the Control Box using  Tapping Screws.
Step 
. Plug the cables to Control Box.
Step 
Control Box Label
WARNING
Use only components with matching labels. Using table with mismatched controller and legs
can result in leg stage separation causing table to fall resulting in possible personal injury.
Switch Installation
Note: If table is using the LO smart paddle kit, see instruction sheet
BHGK for switch installation details.
. Install the Switch using  Tapping Screws in the predrilled
corner holes in the worksurface.
Note: Switch can be installed either right or le side of table.
Cables will be fastened to surface in step .
Note: If legs are inbound the switch location will
also move inbound.
. Verify that Standard (single stage) “SS” or “HS” or Extended (dual stage)
“DS” Symbol on control box label matches the symbol on the Leg Column’s
Cord Label.

4HermanMiller Installation Instructions1BN5FF rev A
Step 
. Plug the switch cable to Control Box.
Step 
. Plug the Power Cord to Control Box.
Step 
. Fasten the Cable Holders to the work surface with the switch and
leg cables in the Cable Holders.
Step 
. Turn Table upright and plug in power cord to receptacle.
. Cycle worksurface all the way up and down to verify legs are
synchronized.
Note: If legs are not synchronized, synchronize them by running the legs all
the way down and holding for  seconds and then repeat Step .

5HermanMiller Installation Instructions1BN5FF rev A
Disassembly for Recycling:
Disassembly for Reconguration:
Materials Identication and Segregation:
Where possible, plastic components are marked with ASTM recycling
codes. Use these codes to identify material type for recycling. Non-marked
components should be treated as mixed plastic. Ferrous metals can be
identied using a small magnet for recycling. Non-ferrous metals should be
separated and recycled separately.
For instructions on how to disassemble legs, see environmental information
section of Renew product page at hermanmiller.com
WARNING
Risk of fire and shock, use only SJT type 18 AWG cord.
a) Clear full range of motion of the table.
b) Clear any shelf stops.
c) Lower table completely to minimum height.
d) Dissemble table.
e) Do not interchange control boxes between leg sets/tables
when reassembling.
WARNING
Lower legs completely to minimum height before
disassembling table. Failure to do so can result in leg
stage separation causing table to fall, resulting in
possible injury. See instructions for details.
For more information about our products and services please visit us at
hermanmiller.com or call ()  .
© Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A. Part No. BNFF  A