HiB Novum N18DU60MWH User manual

Fitting Instructions
Thank you for purchasing this HiB product.
Please read through these instructions carefully and refer back to
them during installation to ensure that your product is fitted safely
and that it retains its high quality finish.
BLEND DRAWER UNIT
60cm Matt White: Art No N18DU60MWH / 60cm Greystone: Art No N18DU60GST
60cm Sherwood Oak: Art No N18DU60SWO / 80cm Matt White: Art No N18DU80MWH
80cm Greystone: Art No N18DU80GST /80cm Sherwood Oak: Art No N18DU80SWO
Blend 60cm Drawer Unit
Blend 80cm Drawer Unit
FI#03 015 R201013 Ver 1.0 Jan 2021

2
• Please read the instructions and warnings carefully before installing the
product and ensure this document is kept with the product for future
reference to ensure product longevity and in the interest of safety.
• This product is intended for domestic use only.
• Not for use in saunas, steam rooms.
• It is recommended that this product is installed by 2 people who are able
to meet the level of competence required in order to comply with relevant
regulations.
• This product is designed for installation into a brick or masonry block wall. If
mounting onto other substrate, ensure appropriate fixing and batons are used
(if required) and the load bearing of the wall is sufficient.
• When drilling use appropriate eye protection.
• Take care when using power tools near water - the use of a residual current
device (RCD) is advised.
• Beware of hidden cables or pipes. Take care if drilling on tiled surfaces in case
the drill slips.
• Do not overload shelves or unit.
• Do not sit or stand on the unit.
• Ensure that excessive standing and surface water is removed from the product
to avoid long term damage and spoiling.
Warnings for Safe Use

3
hib.co.uk
What’s in the Box?
Tools Required
• Drawer Unit
• Fitting pack
• Connecting bolts
Pencil
Drill Drillbit
Tape
Measure
Spirit Level Silicone Screwdriver

4
Figures
Fig. 1
Fig. 3
Fig. 2
aa

5
hib.co.uk
Installation
Please ensure that the wall is suitable for wall hung furniture. For stud wall
installations, add an extra timber support into the stud wall prior to finishing
the wall to improve strength.
1. HiB recommends removing the drawer(s) prior to installation. See Fig. 4,
overleaf.
2. Plan the unit position on the wall, ensuring there is sufficient space between the
unit and other items of furniture in the room.
3. Measure the spacing on the back of the unit, between the two inner sides of the
carcass (Fig. 1, A) this is the maximum bracket spacing. Determine the required
mounting point height.
4. Transfer measurements onto wall using a spirit level to ensure that they are
straight and level, and spaced correctly as per Fig. 1.
5. Drill holes for wall brackets and fix into position with suitable fixings.
6. Position the unit(s) onto the wall brackets.
7. Use furniture hangers to adjust alignment of furniture unit(s) (Fig. 6, screw B,
overleaf), ensuring that they are level.
8. If installing multiple units side by side, once they are both in the correct
position, clamp them together using speed clamps and fix together using the
fixings provided, as per Fig. 2.
9. Once the unit(s) are in position, adjust the screw on the furniture hanger (Fig. 6,
Screw A, overleaf) to bring the furniture tightly against the wall.
10. Refit the drawers.
11. Silicone along back edge of the drawer unit where the drawer meets the wall,
as per Fig. 3. Allow to set fully before use.

6
Adjustment & Removal
+
+
a
b
Fig. 6
Fig. 4 - Removal Fig. 5 - Adjustment

7
hib.co.uk
Care
Aftercare
In the unlikely event that this product should fail please contact the retailer from
which the item was purchased.
To preserve the high quality finish of your HiB product, please ensure you regard
the following care and cleaning recommendations:
• Use only a so damp cloth.
• Wipe off all water spillages as soon as possible.
• Do not use any abrasives or solvents.

©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try
and make sure they are as accurate as possible. In the interest of continuous product development, HiB reserves the right to alter specifications as necessary.
E & OE.
T: [phone] F: [phone] E: [e-mail] hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN